MTD 439-305 User Manual

MTD

PARTS LIST FOR SPREADER

10 CENTS

MODEL 439-305

13 !4

Ulus.

No.

2 710-192 3

5 6 710-473 7 310-2080 8 9

10 11 712-148 12 736-147 13 305-2091

15 312-2087 16 736-235 17

18 19 720-500 20 21 22 710-467

23 312-2082

+ 312 ■awa:

Part

No.

371-2075 305-1387

712-425

714-507

503-4009

716-508

310-2083 503-4006

312-2081

732-497 710-144

310-4357 310-2084

ASSEMBLY INSTRUCTIONS

Price Description

$5.00

»37$

+ Not shown in illustration * Available locally

Hopper - Complete with Agitator, axle

and bearings .20 Bearings in Hopper .20* 10-24 X 3/8" Lg. Truss Hd. Mach.

Sew. (8) .20*

10-24 Square Nut (14)

.20* 3/32 X 3/4 Lg. Cotter Pin (2)

2.30 Drive Wheel with tire .20* 10-24x1/^ Lg. Truss Hd. Mach. Sew. (2) .90 Shutter Bar .20 Clevis Clip .80 Control Rod

2.30 Free Wheel with Tire .20* 10-24 Wing Nut .20* No. 10 External Lock Washer (5) .30 Grip - Handle

1.00 Handle

1.00 Leg (2) .20* Flat Washer (2) .50

Spring

10-24x1%” Lg. Rd. Hd. Mach. Sew. (2)

.20* .30

Grip - Control Rod

.50 Indicator Bracket

Control Bracket

.50

10-24x1" Lg. Truss Hd. Mach. Sew. (2)

.20*

Handle Braces (2)

.50 .80 Pivot Bracket (2)

l.SO Screw Pack

( ) - No. Required Per Assembly

• Spreader should always be in closed position when setting is made or when loading hopper. • When rod is off indicator hook and down, it’s in closed position.

• Make setting by sliding indicator to desired opening and tightening wing nut. When ready to operate just hook rod on indicator. • To determine setting refer to chart. Some experimentation may be necessary be cause of variations of different products.

1. Attach top hole of legs to hooper with 3/8 long bolts and nuts.

2. Lap arms over legs, as shown, and fasten with two 3/8 long bolts and two Vi bolts and nuts.

3. Assemble control bracket and indicator as shown in diagram “A”.

4. Slip control bracket on handle and fasten with the two 1” long bolts and nuts. (Do not reverse control bracket).

5. Secure handle to arms with two 1(4 long bolts and nuts.

5. Washer, spring, washer should be on rod as shown. Insert this into control bracket from bottom and swing rod into position.

7. Straddle clip over shutter bar hole. Slip rod thru clip and shutter bar. Then swing clip up on rod. This must be on as shown in order to have free shutter action.

8. Complete assembly by^adding both grips.

MTID T^RODUCTS I3SrC

FORM NO. 770-1873

CARE OF SPREADER - Before putting spreader away

flush hoppeiK agitator, and shutter with water. If seed is used, washing is not necessary. Cover bottom of hopper with a light film of oil to prevent corrosion...When spreader is not in use store in closed position. This prevents prolonged tension on spring...Avoid using damp materials or exposing spreader

to rain.

Shutter should open evenly and be snug on entire length of hopper. If adjusting your shutter becomes nece ssary, invert the spreader and loosen the four bolts slightly. Tap shutter into correct position and retighten. Shutter opening should be V4” at #8 indi cator setting.

5389 WEST 130th ST.

P.O. BOX 2741

CLEVELAND, OHIO 44111

IITHO IN U.S.A.

IMPORTANT; USE THIS CONVENIENT ORDER BLANK.

Fill in complete data requested on this form to assure that your order will be shipped promptly.

A new instruction sheet will be returned with the

parts you order.

THIS CARTON WAS INSPECTED IF THERE ARE ANY SHORTAGES, PLEASE REFER TO THE ABOVE INSPECTOR NUMBER.

QUAN.

TITY

PART NUMBER

)TE: Add 30if for postage and handling on all orders of

$2.00 or less. On orders of more than $2.00 add 15% for postage and handling.

IMPORTANT: Be certain your name and address are on

your order. An amazing number of orders are in the “no name” file and cannot be shipped until we get a letter of complaint. If you have any reason to be dissatisfied, advise or give us a chance to make things right. We

genuinely try to give satisfaction.

REMITTANCE: Payment in full should accompany all orders. Money Order, Check or Bank Draft are recommend ed. Avoid sending cash unless absolutely necessary. If

you send cash, wrap it in heavy paper and REG&TER

YOUR LETTER. Sorry, no C.O.D.'s.

PRICES are subject to change without notice.

NAME OF PART

Ohio residents add 4% Sales Tax

This item is guaranteed to be free of defects in workmanship and/or materials. Under this warranty, MTD Products Inc is limited to the replacing of any part or parts which shall be returned, postpaid, and which our examination shall disclose to have been defective. Any part or parts which are damaged by misuse or accident in handling are not covered by this warranty.

Postaae and Handlina

Total Amount Required

WARRANTY

PRICE

EACH

TOTAL

Defective parts or shortages must be reported to the factory immediately. Such claim should be reported on this form and must be accompanied by the following information:

1. Equipment name and model number.

2. Date of purchase

.....................................

3. Part number and description of part

4. Description or nature of defect . . ________________________—^

-------------------------------

——

---

......—.-----------------------------------—

________

____

___—-

-------------------------------------------

-----------------------------------

-----------------------------

--------------------

Do not forward any payment with a warranty or shortage claim. The factory will advise you if payment is due.

MiTID F>K,OIDXJCTS I3STC . 5389 WEST 130th ST.

P.0, BOX 2741

CLEVELAND, OHIO 44111

PRINTED IN U.S.A.