MTD YMESV1300, 41ABESPG901 Owner’s Manual

Operator's Manual

YMESV1300

Electric

Mulching

Blower/Vacuum

)

/ /

0(_)0,

PRINTED IN U.S.A. PART NO. 769-00950A

SAVE THESE INSTRUCTIONS

(1/o4)

DO NOT THROW AWAY

THANKYOU

Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device. This operator's manual provides you with easy-to- understand operating instructions. Read the whole

manual and follow all the instructions to keep your new outdoor power tool in top operating condition.

TABLE OF CONTENTS

Service Information ......................... 2

Rules for Safe Operation ..................... 3

Know Your Unit ............................ 6

Assembly Instructions ....................... 7

Operating Instructions ....................... 9

PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS

All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

SERVICE INFORMATION

Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer.

For service call 1-800-345-8746, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near

you. For more details about your unit, visit our website at www.yardman.com.

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, please call the Customer Support Department.

Maintenance and Repair Instructions ........... 14

Troubleshooting Chart ...................... 15

Specifications ............................. 15

Warranty Information ....................... 18

Parts List .................... Inside Back Cover

Before beginning, locate the unit's model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future reference.

Serial Humber --_

Model Humber

\ Parent P_ Number

\MODEL: /

S/N: iTEM: J

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR

Copy the model and parent

part number here:

WARRANTY SERVICE.

Copy the serial number

here:

Make sure you carefully read and understand this manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.

Thepurposeofsafetysymbolsistoattractyour

attentionto possibledangers.Thesafetysymbols, andtheirexplanations,deserveyourcarefulattention

andunderstanding.Thesafetywarningsdonotby

themselveseliminateanydanger.Theinstructionsor

warningstheygivearenotsubstitutesforproper accidentpreventionmeasures.

SYMBOL MEANING

DANGER: Failure to obey a

result in serious injury to yourself or to others. Always follow the safety precautions

to reduce the risk of fire, electric shock and personal injury.

safety warning will

SAFETY ALERT: Indicates

warning or caution. Attention is required in

order to avoid serious personal injury. May be used in conjunction with other symbols

or pictographs.

NOTE: Advises you of information or instructions vital

to the operation or maintenance of the

equipment.

danger,

• IMPORTANT SAFETY INSTRUCTIONS •

READ ALL INSTRUCTIONS

BEFORE OPERATING

When using the unit,

WARNING: you must followthe

safety rules. Please read these instructions before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

• Read the instructions carefully. Be familiar with the controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children and teens under the age of 15 must not use the unit, except for teens guided by an adult.

• Before each use, thoroughly inspect your unit for loose or damaged parts. Do not use until adjustments or

repairs are made.

• All guards and safety attachments must be installed

properly before operating the unit.

• Use the right tool. Use this unit only as described in this manual. Do not use for any job except that for which it is intended. Use only the manufacturer's

recommended attachments.

• Inspect the area before starting the Blower/Vacuum.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

WARNING: Failure to obey a

result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock and

personal injury.

_ Failure obey a

result in property damage or personal injury to yourself or to others. Always follow the

safety precautions to reduce the risk of fire, electric shock and personal injury.

• Use the unit only in daylight or good artificial light.

• Keep all bystanders, especially children and pets, at least 50 feet (15 m) away from the unit while operating.

ELECTRICAL SAFETY WARNINGS

• Since the tool is double-insulated, a 2-wire extension cord (an extension cord without a ground) may be used. A 3-wire extension cord (an extension cord with a ground) that uses a NEMA type connector (parallel blade, U ground)is recommended. Extension cords are available from your local retailer. Use only round- jacketed extension cords approved for outdoor use.

• This tool isdouble-insulated. Repairor replace damaged cords.

ING: To reduce the risk of

only SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-W or SJTOW-A cord types.

• To reduce the risk of electrical shock, this unit has a polarized plug (one blade is wider than the other). This

unit will fit with a polarized plug in one way only. If the plug does not fit fully into the unit, reverse the plug. If

it st=lldoes not fit, use a cord with the correct connection. Do not modify the unit in any way.

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-12 AMPS*

safety warning can

safety warning may

electrical shock, use

DANGER: When using electric

basic safety precautions should always be

followed to reduce the risk of fire, electric shock

and personal injury. Carefully read and understand the entire operator's manual before

using your unit. Pay close attention to the operating instructions and safety warnings.

gardening appliances,

Cord length (ft.) 25 50 100 150

Wire size (AWG)* 16 16 16 14

*The wire size (AWG) for appliances using 12 to 16 amps is 14 AWG for 25 feet, 12 AWG for 50 feet, and

not recommended for 100 or 150 feet.

• CORDSETS:Makesureyourcordsetisingood condition,withacordthatisheavyenough_ocarry

thecurrentthatyourunitwilldraw.Anundersizedcord setwillcauseadropinlinevoltageresultingina loss

ofpower,aswellasoverheating.Thetableshown aboveillustratesthecorrectsizetousedependingon

thecordlengthandnameplateamperagerating.Ifin doubt,usethenextheaviersizelinegauge.The smallerthegaugenumber,theheavierthecord.To

preventthecordfromdisconnectingfromtheunit,use

thecordhookshownintheOperating Instructions.

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) that will

be used for the unit. Use receptacles with built-in

GFCI protection for an extra measure of safety.

• A nameplate on your unit indicates the voltage used.

Never connect the unit to an AC voltage that differs

from this voltage.

• Inspect all extension cords and the unit power connection

periodically. Look closely for deterioration, cuts or cracks _nthe insulation. Also inspect the connections for damage. Repair or replace the cords if any defects appear.

• Avoid dangerous environments. Never operate your unit

in damp or wet conditions. Moisture is a shock hazard.

• Do not use the unit in the rain.

• Do not handle the plug or the unit with wet hands.

WHILE OPERATING

• Wear safety_glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty. Long

sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelw, short pants, sandals or

go barefoot. Secure hair above shoulder level.

• Avoid accidental starting. Do not carry around a unit that is plugged in with your finger onthe trigger switch. Be sure the sw_tch is in the off posit_on when

plugging in the unit.

• Do not set unit on any surface except a clean, hard area while motor is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air

intake and thrown out by the discharge opening,

damaging unit, property, or causing serious injury to

bystanders or operator.

• Use extra care when cleaning on stairs.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

• Do not use to pick up flammable or combustible

liquids, such as gasoline, or use in areas where they may be present.

• Do not overreach. Always keep proper footing and

balance. Do not operate from unstable surfaces like ladders, trees, slopes or rooftops.

• Do not abuse the power cord. Do not pull or carry the

unit by the cord, use the cord as a handle, close a

door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces, oil and sharp edges.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Always remain alert. Use common sense. To prevent

injury to yourself and others, do not operate this unit if

you are fatigued.

Do not operate the unit while under the influence of drugs, alcohol or medication.

Do not leave the Blower/Vacuum plugged in when not in use, changing tubes, or while being

serviced. Do not put any object into openings. Do not use with

any opening blocked; keep free of dirt, debris and anything that may reduce the air flow.

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

Use only original equipment manufacturer replacement parts when servicing this unit. These parts are available

from your authorized service dealer. Do not use unauthorized parts, accessories, or attachments for

this unit. Doing so could lead to serious injury to the

user, or damage to the unit, and void your warranty. Do not force unit. It will do the job better and with less

likelihood of injury at a rate for which it was designed. Never use the Blower/Vacuum without the

blower/vacuum tube and vacuum bag attached.

Turn off all controls before unplugging.

Unplug the Blower/Vacuum before attempting to install or remove the blower/vacuum tube or

vacuum bag. The unit must be unplugged, and the impeller blades stopped to avoid contact with the

rotating blades.

WHILE OPERATING UNIT AS A BLOWER

• Never point the blower in the direction of people or pets, or in the direction of windows. Always direct the blowing debris away from people, animals, and windows. Use extra caution when blowing debris near

solid objects such as trees, automobiles, walls, etc.

WHILE OPERATING UNIT AS A VACUUM

• Avoid situations that could catch the vacuum bag on fire. Do not operate near an open flame. Do not

vacuum warm ash from fireplaces, barbecue pits, brush piles, etc. Do not vacuum discarded cigars or

cigarettes unless the cinders are completely cool.

The unit is designed to pickup dry material such as

leaves, grass, small twigs, and bits of paper. Do not attempt to vacuum wet debris and/or standing water

as this may result in damage to the blower/vacuum.

To avoid severe damage to the impeller, do not

vacuum metal, broken glass, etc.

OTHER SAFETY WARNINGS

• Be sure to secure the unit while transporting. Store the unit in a dry area, locked up to prevent

unauthorized use or damage, and stored in a high place out of the reach of children.

Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after each use. See the Cleaning and Storage instructions.

Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVETHESE INSTRUCTIONS

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.

• WARNING - READ OPERATOR'S MANUAL

Read the Operator's Manual(s) and follow all warnings and safety

instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

WEAR EYE AND HEARING

PROTECTION

WARNING:Thrown

objects and loud noise can cause severe eye injury and hearing loss.

Wear eye protection meeting ANSI Z87.1-1989 standards and ear

protection when operating this unit. Use a full face shield when needed.

• DO NOT USE IN THE RAIN

WARNING:Avoid

dangerous environments. Never operate your unit in the rain, or in damp or wet conditions. Moisture is

a shock hazard.

BLOWERS- ROTATING IMPELLER BLADES CAN

CAUSE SEVERE INJURY

WARNING: Stopthe

motor and allow the impeller to stop before opening the vacuum door,

installing or changing tubes or bag,

or before cleaning or performing any

maintenance.

<_=_ • BLOWER/VACUUM MODE

B A - Vacuum mode

CHANGE-OVER LEVER

B - Blower mode

THROWN OBJECTS AND ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WAR NING: Keep clear

of blower outlet. Never point the blower at yourself or others. Objects

can be thrown from blower. Do not operate unit without proper

attachments and guards in place.

• KEEP BYSTANDERS AWAY

WARNING: Keep all

bystanders, especially children and pets, at least 50 feet (15 m.) from the

operating area.

• DOUBLE INSULATED Two systems of insulation are

provided instead of grounding. There is no grounding provided and no means of grounding should

be added to this unit.

APPLICATION

As a blower:

• Cleaning of yards, garages, driveways, porches, patios, around walls, fences, etc.

As a vacuum:

• Picking up leaves, light debris, etc.

Vacuum Inlet

_=" Blower/Vacuum Tube Power/Speed Switch

Support

Fitting

]

Blower Outlet

Vacuum Bag Hook

Blower/Vacuum Mode

Change-Over Lever

Motor Air

Vents

Cord

Receptacle

< / Vacuum Bag

_.._.__._j__ Li vacuum Bag Zipper

ATTACHING AND REMOVING THE BLOWER/VACUUM TUBE

To avoid serious

WARNING: personal injury, the

blower/vacuum tube and vacuum bag must be used when operating this unit.

Attaching NOTE: The blower/vacuum tube comes unassembled

on this unit. Installation is required to provide safe and easy use for the operator.

To prevent serious

WARNING: injury, make sure the unit is in the off position, it is unplugged,

and the impellers have stopped before attaching or removing tubes.

1. Remove the screws and nuts provided from the hardware pack.

2. Insert the blower/vacuum tube all the way into the opening on the motor housing until the holes in the tabs on the blower/vacuum tube align with the screw holes in the housing (Fig. 1).

3. Insert the 2 (two) 8-32 x 3/4" slotted T20 Torx screws into the right side of the motor housing and the 2 (two) nuts into the left side of the motor housing (Fig. 1).

Removing

NOTE: It may be necessary to remove the

2. Remove the 2 (two) screws and nuts holding the

NOTE: Keep the hardware in a safe place for future use.

blower/vacuum tube to clear a blocked tube or impeller.

WAR NING: Toprevent serious

unit is in the off position, it is unplugged, and the impellers have stopped before

attaching or removing tubes.

Remove the 2 (two) self-tapping screws from either

side of the housing.

blower/vacuum tube on the housing (Fig. 2).

injury, make sure the

Motor Housing

Nut

Blower/Vacuum

Screw

Self-Tapping Screw

Fig. 1

Tighten the screws firmly. Do not over-tighten.

Install the 2 (two) remaining self-tapping 8-16 x 3/4" slotted T20 Torx screws into the holes on either side

of the housing (Fig. 1). Tighten until snug, do not over-tighten.

Tube

Screw Self Tapping

and Nut Screw

Screw and Nut

Fig. 2

3. Remove the blower/vacuum tube from the motor housing.

4. Replace blower/vacuum tube before use.

ATTACHING AND REMOVING THE VACUUM BAG Attaching

1. Attach the vacuum bag to the vacuum bag hook on the blower/vacuum tube (Fig. 3).

Vacuum Bag Hook

INSTALLING THE SHOULDER HARNESS (Optional)

The shoulder strap is an optional accessory.

1. Push the strap through the center of the buckle.

2. Pull the strap over the cross bar and down through the slot in the buckle (Fig. 6).

Fig. 3

Slide the vacuum bag tube over the debris exhaust tube on the housing. Push the tube until the latching

tabs on both sides click into place, securing the bag on the unit (Fig. 4).

__J

Latching Tabs

Fig. 4

Removing

1. Press the latching tabs on both sides of the vacuum bag tube and pull the vacuum bag down from the unit (Fig. 5).

2. Detach the vacuum bag from the vacuum bag hook.

Debris Exhaust Tube Vacuum Bag Tube

Vacuum Bag

Zipper

/_ Clip

Fig. 6

3. Snap the clip on to the support fitting (Fig. 7).

Support Fitting

Clip

Fig. 7

While standing in the operating position adjust length to fit the operator's size. Pull tab to lengthen, pull strap to shorten (Fig 8).

PRESS IN

Latching Tabs

Fig. 8

Fig. 5

CONNECTING THE POWER CORD

Use a minimum 25 foot (7.6 m) long, 16AWG, outdoor electrical cord when using this unit. Other sizes include:

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-12 AMPS

2. Plug the female end of the electrical cord into the receptacle at the back of the unit (Fig. 10).

Cord length (ft.) 25 50 100 150

Wire size (AWG) 16 16 16 14

WARNING: To reduce the risk of

electrical shock, this

unit has a polarized plug (one blade is wider

than the other) and will require the use of a

polarized extension cord.

This unit plug will only fit into a polarized extension cord

in one orientation. If the plug does not fully fit into the

extension cord, reverse the plug. Ifthe plug still does not fit, obtain a correct polarized extension cord.

A polarized extension cord will require the use of a

polarized wall outlet. This plug will only fit into a polarized wall outlet in a specific orientation. If the plug

does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the unit

plug, extension cord receptacle, or extension cord plug in any way.

1. Secure the extension cord to the motor housing as shown (Fig. 9). This prevents accidental removal of

the electrical cord.

Receptacle

Fig. 10

STARTI NG/STOPPI NG INSTRUCTIONS

This unit is equipped with a three-way (OFF/LOW/

HIGH) switch (Fig. 11):

• Slide the switch all the way down for OFF.

• Slide the switch up to the first click for LOW.

• Slide the switch up to the second click for HIGH. Once the unit is plugged in, stand in the operating

position (Fig. 12). Slide the power/speed switch to LOW

or HIGH to start the unit. To stop the unit, slide the

switch to OFF (Fig. 11).

Fig. 9

HIGH

LOW

Fig. 11

HOLDING THE BLOWER/VACUUM

Before operating the unit, stand in the operating position. (Fig. 12). Check for the following:

• Operator is wearing proper clothing, such as boots, safety glasses or goggles, ear/hearing protection, gloves, long pants and long sleeve shirt

To avoid serious

WARNING: personal injury,

wear goggles or safety glasses at all times when operating this unit. Wear a face mask

or dust mask in dusty locations.

• If the conditions are dusty, the operator is wearing a dust mask or face mask

• The unit is in good working condition

• The tubes and bag are in place and secure

To prevent serious

WARNING: personal injury or

damage to the unit, make sure blower tubes or vacuum tubes and the vacuum bag are in

place before you operate the unit.

• The vacuum bag is installed and zipped closed (when

used as a vacuum)

Operate power equipment only at reasonable hours-- not early in the morning or late at night when people

might be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 am to

5:00 pm, Monday through Saturday.

To reduce noise levels, limit the number of pieces of

equipment used at any one time.

To reduce noise levels, operate power blowers at the

lowest possible speed to do the job. Use rakes and brooms to loosen debris before blowing.

In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available.

Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens.

Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away.

Clean up after using blowers and other equipment. Dispose of debris appropriately.

OPERATING TIPS

• Be sure the vacuum bag is zipped closed before operating the unit.

• Assure the unit is not directed at anybody or any loose debris before starting the unit.

• Verify that the unit is in good working condition. Make sure the tubes and guards are in place and secure.

• Always hold the unit with both hands when operating.

Keep a firm grip on both the front and rear handle or grips.

• To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

AIR VENTS

Never cover air vents. Keep them free from obstructions

and debris. They must always remain clear for proper

motor cooling (Fig. 13).

Air Vents

Fig. 13

WAR NING: Toavoidserious

not wear loose fitting clothing or articles such as scarves, strings, chains, ties, etc. that

could get drawn into the air vents. To make sure long hair does not get drawn into the air

vents secure hair above shoulder level.

personal injury, do

Fig. 12

OPERATING AS A BLOWER

Converting to a Blower

1. Start the unit. See Starting/Stopping Instructions.

2. Set the blower/vacuum mode change-over lever to the up position (Blower Mode) (Fig. 14).

NOTE: Never use the unit with the lever in a position half

way between either mode.

3. If you are using the optional shoulder harness, place

it over your head and onto your shoulder and adjust it. Refer to Installing the Shoulder Harness.

Vacuum

Mode

Blower

Change-over lever i _<__

Fig. 14

Blower Operating Procedures

Hold the blower as shown in Figures 15, 16 and 17. Sweep from side to side with the nozzle several inches

above the ground or floor. Slowly advance the unit, keeping the accumulated pile of debris in front of you.

Most dry blowing operations are better suited to low speeds, rather than high. High speed blowing is a better

way to move heavier items like large debris or gravel. 1 Use the blower for trees, shrubs, flower beds and

hard-to-clean areas (Fig. 15).

2. Use the unit around buildings and for other normal cleaning procedures (Fig. 16).

3. Use the blower around walls, overhangs, fences and screens (Fig. 17).

Mode

Fig. 15

Fig. 16

/ i

/ fi

/ /

Fig. 17

OPERATING AS A VACUUM

Converting to Vacuum

1. Start the unit. See Starting/Stopping Instructions.

2. Set the blower/vacuum mode change-over lever to the down position (Vacuum Mode) (Fig. 18).

NOTE: Never use the unit with the lever in a position half

way between either mode.

3. If you are using the optional shoulder harness, place

it over your head and onto your shoulder and adjust it. Refer to Installing the Shoulder Harness.

Vacuum

Mode

Fig. 19

Blower

Mode

Change-over lever __ _tl

Fig. 18

To prevent serious

WARNING: personal injury or

damage to the unit, always install vacuum

tubes, the vacuum bag and make sure the vacuum bag is completely zipped closed

when operating this unit as a vacuum.

Vacuum Operation Procedures

Check for the following before operating the unit:

• Operator is wearing proper clothing, such as boots,

safety glasses or goggles, ear/hearing protection, gloves, long pants and long sleeve shirt

• If the conditions are dusty, operator is equipped with a

dust mask or face mask

• The unit is in good working condition-- the vacuum

tubes and vacuum bag are in place and secure.

• The vacuum bag harness is in place and correctly

adjusted

Use the unit for vacuuming up light debris like leaves and paper.

Hold the vacuum, tilting the suction tube slightly (2-4 in or 50-100 mm), and use a sweeping action to collect

light debris (Fig. 19). The debris will flow into the vacuum bag. Items such as small leaves and small twigs will be

mulched as they pass through the fan housing, allowing

the vacuum bag to hold more debris.

When the bag is full, suction will noticeably decrease.

Turn off the unit and allow the impeller to stop before you unzip the bag. Unzip the bag and empty the

contents before continuing. Refer to Emptying the

Vacuum Bag.

WARN ING: Toavoidserious

never unzip the vacuum bag without stopping the unit first.

personal injury,

WAR NING: Asavacuum,the

unit is designed to

pick up dry material such as leaves, grass, small twigs and bits of paper. To avoid

serious personal injury, do not attempt to vacuum wet debris and/or standing water

as this may result in damage to the blower/ vacuum. To avoid severe damage to the

impeller, do not vacuum metal, broken glass or similar items.

WARN ING: Avoidsituationsthat

vacuum bag on fire. Do not operate near an open flame. Do not vacuum warm ash from

fireplaces, barbecue pits, brush piles, etc. Do not vacuum discarded cigars or cigarettes

unless the cinders are completely cool.

NOTE: Empty the bag after each use to avoid

deterioration and obstructing air flow, which will

reduce the performance of the vacuum

could catch the

CLEARING A BLOCKED TUBE / IMPELLER

EMPTYING THE VACUUM BAG

To avoid serious

WARNING: personal injury, be

sure the unit is off and unplugged before

clearing the impeller.

To avoid serious

WARNING: personal injury,

always wear gloves to protect yourself from

the impeller blades or other sharp objects.

1. Slide the Power/Speed switch down inthe OFF position until the unit comes to a complete stop (Fig. 11).

2. Unplug the unit.

3. Remove the vacuum bag and then the blower/vacuum

tube.

Carefully remove material blocking the tube or impeller. Inspect the blades to assure no damage has occurred. Rotate the impeller blades by hand to assure the blockage is completely cleared.

Reinstall the blower/vacuum tube and the vacuum bag.

Plug the unit back into the power supply.

WAR NING: Toavoidserious

never unzip or remove the vacuum bag without first turning the unit off.

NOTE: Empty the bag after each use to avoid

deterioration and obstructing air flow, which will reduce the performance of the vacuum.

1. Unplug the unit.

2. While pressing the latching tabs on both sides of the vacuum bag tube, pull the vacuum bag down off the

unit (Fig. 20).

WARNING: Wear eye protection

when emptying the vacuum bag.

3. Detach the vacuum bag from the vacuum bag hook.

PRESS IN

personal injury,

and a dust mask

Latching tabs

PRESS IN

Fig. 20

4. Unzip the bag and empty the contents into a garbage bag or container.

5. Turn the bag inside out after initial emptying and vigorously shake out dust and debris.

6. Return the bag to outside in, zip the bag closed and

reinstall vacuum bag.

7. Plug the unit back into the power supply.

SERVICING DOUBLE INSULATED UNITS

This unit is double-insulated. In a double-insulated unit, two systems of insulation are provided instead of

grounding. There is no grounding provided and no means of grounding should be added to this unit.

Extreme care and knowledge of the system is required when servicing a double-insulated unit. Service should

be performed by qualified service personnel only. Replacement parts for a double-insulated unit must be

identical to the parts they replace. Refer any repair to an authorized service dealer. A double-insulated unit is

marked with the words "double insulation" or "double insulated."

CLEANING THE UNIT

3. Wash the bag once a year or more often if needed: a. Removethe vacuum bag.

b. Turn bag inside out.

c. Hang it up. d. Hose it down thoroughly.

e. Hang to dry. f. Turn bag right-side out and reinstall.

STORAGE

• Store the unit locked up to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

To avoid serious

WARNING: personal injury,

always turn your unit off and unplug it before you clean or service it.

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

CLEANING THE VACUUM BAG

1. Empty the bag after each use to avoid deterioration and obstructing air flow, which will reduce the performance of the vacuum.

2. Wearing eye protection and a dust mask, clean the bag as needed. Turn the bag inside out after initial

emptying and vigorously shake out dust and debris.

INSPECT EXTENSION CORDS

Inspect all extension cords periodically. Look closely for

deterioration, cuts or cracks in the insulation. Inspect the connectors for damage. Replace cords if defective or

damaged.

Motor Amperage .................................................................................................................................................... 12Amps

Motor Voltage ..................................................................................................................................... A.C.,120 Volts Electric

Blower Air Output ...................................................................................................................... up to 160 mph (257.5 kmh)

Vacuum Air Flow ............................................................................................................................. up to 424 cfm (12 cmm)

Mulching Ratio ...................................................................................................................................................... up to 10:1

Operating Weight ........................................................................................................................................... 10 Ib (4.5 kg)

Vacuum Bag Capacity ........................................................................................................................ 0.75 bushels (26.4 L)

CAUSE

Bag full Blocked tube

Blocked impeller

Damaged impeller Dirty bag

Torn bag

Bag unzipped Unit unplugged

CAUSE

Unit is unplugged Power/Speed switch is in the OFF position GFCI in outlet has tripped (if used)

ACTION

Empty bag, as described in Empty the Vacuum Bag Clear the blockage as described in Clearing a Blocked

Tube/Impeller Clear the blockage as described in Clearing a Blocked

Tube/Impeller

Take the unit to an authorized service dealer Clean the vacuum bag Replace the vacuum bag

Zip up the vacuum bag Plug into an extension cord

ACTION

Check cord to make sure it is plugged into an electrical outlet Slide switch to HIGH or LOW

Reset GFCI

if further assistance is required, contact your authorized service dealer.

+ 39 hidden pages