MTD 31C-040-701 Owner’s Manual

Operator's Manual

odel: 040

Electric

Snow Thrower

MTD

0®

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

P/N 769-05377 (10/09)

THANK YOU

Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator's manual provides you with easy-to-

understand operating instructions. Read the whole manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

TABLE OF CONTENTS

Service Information ......................... 2

Rules for Safe Operation ..................... 3

Know Your Unit ............................ 7

Assembly Instructions ....................... 8

Operating Instructions ....................... 9

PRODUCT REFERENCES, ILLUSTRATIONS AND

SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

Reserved.

SERVICE INFORMATION Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

For service call 1-800-800-7310, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near

you. For more details about your unit, visit our website at www.yardman.com.

If you have difficulty assembling this product or have

any questions regarding the controls, operation or

maintenance of this unit, please call the Customer

Support Department.

Maintenance and Repair Instructions ........... 11

Cleaning and Storage ....................... 12

Troubleshooting Chart ...................... 13

Specifications ............................. 13

Warranty Information ....................... 14

Parts List ............................... $14

Before beginning, locate the unit's model plate. It lists the model and serial numbers of your unit. Refer to the sample plate below and copy the information for future

reference.

Model Number

Serial_mber --_ ParentParerNumber

\MODEL: /

S/N : ITEM : /

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR

Copy the model and parent

part number here:

WARRANTY SERVICE.

Copy the serial number

here:

Make sure you carefully read and understand this manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper accident prevention measures.

SYMBOL MEANING

,_ SAFETY ALERT: Indicates danger, warning or

caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.

SYMBOL MEANING

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the

risk of fire, electric shock and personal injury.

WARNING: Failure to obey asafety warning can

result in injury to yourself and others. Always follow

the safety precautions to reduce the risk of fire,

electric shock and personal injury.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

Read the Operator's Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-800-7310 IN U.S. OR 1-800-668-1238 in CANADA

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to

yourself or to others. Always follow the safety

precautions to reduce the risk of fire, electric shock and personal injury.

• IMPORTANT SAFETY INSTRUCTIONS •

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety

instructions could result in serious injury.

READ ALL INSTRUCTIONS

When using the unit,

WARNING: you must followthe

safety rules. Please read these instructions before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

Before Operating

• Read the instructions carefully. Be familiar with the controls and proper use of the unit. Know how to stop

the unit and disengage the controls quickly.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children under the age of 15 must not use the unit; teens may operate ttie unit with adult guidance.

• Inspect the unit before use. Replace damaged parts.

Make sure all fasteners are in place and secure. Replace snow thrower parts that are cracked,

chipped, or damaged in any way.

• Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

• Thoroughly inspect the area where the snow thrower is to be used. Remove all doormats, sleds, boards, wires,

debris, and other foreign objects which may be thrown

by the snow thrower.

° Clear the area of bystanders and pets, particularly small

children. At a minimum, keep all children, bystanders and pets outside a 50 ft. (15 m) radius; there still may be

a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If

approached, stop the unit immerdiately.

• Make sure the rotor will spin freely before using the unit.

Dress properly. Wear adequate winter outer garments. Wear heavy, long pants, boots, gloves and a long sleeve

shirt. Do not wear jewelry, short pants, sandals or loose clothing that can get caught in moving parts. Do not go

barefoot. Secure hair above shoulder level. Wear footware that doesn't leak when operating the

snow thrower and that will improve footing on slippery surfaces. Wear rubber boots.

Never attempt to make adjustments while the motor is running.

Let the motor and unit adjust to outdoor temperatures before starting to clear snow.

Always wear safety glasses/shields or goggles at all times during operation or while performing an

adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

SAFETY WARNINGS FOR ELECTRIC UNITS

DANGER: When using electric machines, basic

safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Carefully read and understand the entire operator's manual before using your unit. Pay close attention to the operating instructions and safety warnings.

• This snow thrower should be grounded while in use to protect the operator from electric shock. The snow

thrower is equipped with an approved 3-conductor cord and 3-prong grounding-type plug to fit the proper grounding-type receptacle. The green or green/yellow

conductor in the cord is the grounding wire. Never connect this wire to a live terminal. If your unit is for

use on less than 150 volts, it has a plug that looks like

A in the figure below. If it is for use on 150 to 250 volts, it has a plug that looks like D in the figure.

__ Metal

Gro Screw _l) J

Grounding Grounding D

Means Pin

• An adapter (show in B and C in the above figure) is

available for connecting 3-prong grounding-type plugs to 2-prong receptacles. The grounding means

extending from the adapter must be connected to a

permanent ground such as a properly-grounded outlet box. No adapter is available for the plug shown in D.

• Use only 3-wire outdoor extension cords that have 3- prong grounding-type plugs and 3-pole receptacles

that accept the snow thrower's plug. Replace or repair damaged cords.

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-12 AMPS

Cord length (ft.) 25 50 100 150

Wire size (AWG) 16 16 14 14

CORD SETS: Please see your dealer for the appropriated extension cord to use with this product.

Make sure your cord set is in good condition, with a

cord that is heavy enough to carry the current that your unit will draw. An undersizedcord set will cause a

drop in line voltage resulting in a loss of power, as well as overheating. The table shown above illustrates the

correct size to use depending on the cord length and

nameplate amperage rating. If in doubt, use the next heavier size line gauge. The smaller the gauge number, the heavier the cord. To prevent the cord

from disconnecting from the unit, use the cord hook shown in the Operating Instructions.

'_1 WARNING: To reduce therisk of electrical I

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) that will be used for the unit. Use receptacles with built-in GFCI protection for an extra measure of safety.

° A data plate on your unit indicates the voltage used.

Never connect the unit to an AC voltage that differs from this voltage.

,_IWARNING: Topreventelectricshock, useonly I

Inspect all extension cords and the unit power connection periodically. Look closely for deterioration, cuts or cracks in the insulation. Also inspect the connections for damage. Repair or replace the cords if any defects appear.

When cleaning, inspecting or repairing the unit, make certain the rotor and all moving parts have stopped.

Disconnect the extension cord to prevent accidental starting.

Do not abuse the extension cord. Never carry the snow thrower by the cord or yank on the cord to

disconnect it from the receptacle. Keep the extension cord away from heat, oil, and

sharp edges to prevent damage. If the extension cord is damaged in any manner while

it is plugged in, pull the extension cord from the wall receptacle.

Prevent any possible disconnection of the cord receptacle from the extension cord during operation by using the cord retainer and guide bar. Refer to the section Using the Cord Retainer.

Avoid accidental starting. Don't carry a plugged-in snow thrower with your finger on the switch. Be sure switch is off when plugging in the unit.

Always unplug the unit and allow it to cool before putting it into storage. Store indoors.

Always unplug the unit when not in use, and before performing any maintenance or repairs.

WHILE OPERATING

• Check ALL bolts at frequent intervals for proper tightness to be sure the unit is in good, safe working

condition.

• Be sure the snow thrower is not in contact with anything before starting the unit.

• Stay away from the discharge opening at all times. Keep face, hands, and feet away from concealed

moving or rotating parts.

• Be attentive when using the snow thrower, and stay alert for holes in the terrain and other hidden hazards

or traffic.

shock, use onlySW-A, SOW-A, STOW-A,SJW-A,

SJOW-A,SJTW-Aor SJTOW-Acord types.

with an extension cord suitable for outdoor use.

° Do not use on a gravel surface or crushed rock

surfaces. Use extreme caution when crossing gravel/ crushed rock drives, walks, or roads. Stay alert for

hidden hazzards or traffic.

° Clear snow from slopes by going up and down. Never

go across the slope. Use caution when changing directions. Never clear snow from steep slopes.

° Never attempt to use the snow thrower on a roof or

any steep, inclined, slippery surfaces.

° Never operate snow thrower without proper guards,

plates or other safety protective devices in place.

° Never operate the snow thrower near glass

enclosures, automobiles, trucks, window wells, dropoffs, etc. without proper adjustment of the snow discharge angle. Keep children and pets away.

° Don't force or overload the snow thrower. The snow

thrower will perform at its best and safest when it is

run at the rate for which it was designed.

• Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing up.

° Never direct discharge towards people or areas where

property damage can occur. Keep children and others

away.

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1 standards, and ear/hearing protection when operating this unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Remain in the starting

position whenever starting the unit. The operator and unit must be in a stable position while starting. See

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

° Always hold the unit with both hands when operating.

Keep a firm grip on handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the rotor

when it is rotating.

• If the rotor will not rotate freely due to frozen ice, thaw the unit thoroughly before attempting to operate it

under power.

• Keep the rotor clear of debris.

• Never attempt to clear the rotor with the motor

running. Turn the motor off first and unplug the

extension cord.

• Keep clothing and body parts away from the rotor.

• Do not overload the machine capacity by attempting to clear snow at too fast a rate.

° Always stop the motor when clearing snow is delayed

or when walking from one location to another.

° Disengage power to the rotor when snow thrower is

transported or not in use. After striking a foreign object, turn the unit off and

inspect the snow thrower for damage. Unplug the unit. Repair damage before restarting and operating

the unit.

• If the unit should start to vibrate abnormally, stop the unit and check immediately for the cause. Vibration is

generally a warning of trouble.

• Stop the motor and unplug the unit whenever you leave the operating position, before unclogging the

rotor or discharge vanes, and when making any repairs, adjustments, or inspections.

Never discharge snow onto public roads or near moving traffic.

Let the snow thrower run for a few minutes after clearing snow so moving parts do not freeze.

Use only original equipment manufacturer replacement parts and accessories for this unit. These

are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to

serious injury to the user or damage to the unit, and void your warranty.

Do not use the unit in the hand held position. Do not pick up the unit when it is powered and running. The unit is designed to travel along the ground.

Never operate the unit without good visibility or light.

Always be sure of your footing and keep a firm hold

on to the handles, walk never run.

OTHER SAFETY WARNINGS

• Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to prevent unauthorized use or damage, out of the reach

of children. Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris. Clean after each use, see Cleaning and Storage

instructions. Maintain or replace safety and instructional labels as

necessary. If the labels on the unit become defaced or start lifting off, contact an authorized service dealer.

Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

• Maintain snow throwers with care. Follow instructions for lubricating and changing accessories.

SAVE THESE INSTRUCTIONS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.

• WARNING - READ

OPERATOR'S MANUAL

Read the operator's manual(s)and follow all warnings and safety instructions. Failureto do so can result in serious injury to the operator and/or bystanders.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,

especially children and pets, at least 50 feet (15 m) from the operating area.

SYMBOL MEANING

• THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING: Small objects can be

propelled at high speed, causing injury. Keep away from the rotating rotor.

• SPINNING ROTOR CAN CAUSE

SEVERE INJURY

WARNING: Keep hands, feet, and

clothing away from the discharge area.

Do not step in front of the unit, or use hands to clean the rotor area.

• KEEP HANDS AND FEET AWAY

APPLICATIONS As a snow thrower:

° Clears snow from walkways, driveways, sidewalks,

pathways and more

Starter

Button

Key

Starter

Key Hole

Bail

Overload \"

Protection

Switch

Front Handle

Discharge

Directional /

Control

Cord

Retainer

Handlebar

Cord Guide

Bar

Cord Outlet

Receptacle

Handlebar

Knob

Vanes

Rotor

Belt Case Cover

Flange Lock Nut

Wheels

Cover

Screws (7)

Scraper

ASSEMBLING THE HANDLEBARS

Before you can operate the unit, you must install the handlebars.

1. When unpacking the unit, loosen and remove the two knobs and washers from the inside of the lower

bars (Fig. 1).

2. Hold the handle bar in the position shown in Figure 1

and slide it onto the lower bars making sure that the ends of the handlebar are on the inside of the lower

bars.

3. Align the holes in the upper handlebar, lower

handlebar and vane control bracket. Insert the bolts

through the holes.

4. Place the washers on the bolts, then screw the two

knobs onto them.

NOTE: Take care not to pinch the switch cable when

positioning the handlebars.

5. Tighten the knobs to secure the handlebars in place.

NOTE: Do not over-tighten the knobs.

6. Clip the switch cable to the cable restraint on the

lower bar as shown in the inset of Figure 1.

7. Remove the banding once the upper handle is

assembled to the lower handle (Fig. 1).

8. Make sure the bail is installed into switch assembly

(Fig. 1).

USING THE CORD RETAINER

There is an extension cord retainer to prevent the

extension cord from disconnecting during use. The retainer hangs from the cord guide bar.

NOTE: Do not plug the extension cord into the power

source receptacle until the cord is connected to

the cord retainer and plugged into the unit.

To use the cord retainer:

Fold the extension cord in half, forming a tight loop near the receptacle.

Push the loop through the bottom hole in the retainer (Fig. 2).

Slide the loop over the retaining clip and pull down until the cord fits snugly (Fig. 2).

NOTE: Use a UL-approved extension cord. A 100-foot,

14-gauge cord is recommended. A 50-foot, 16- gauge cord is acceptable.

Both the cord retainer and guide bar restrain the extension cord and keep it out of the way at all times,

safely to the side of the operator.

The extension cord and retainer will slide on the guide

bar as the unit is moved to the left and right. Connect

your extension cord to the unit as shown in Figure 3.

Banding

Fig. 1

Fig. 2

Cord Will Slide

Side to Side

Cord

Guide Bar

Fig. 3

STARTING INSTRUCTIONS

to stand inthe starting position when using the WARNING: Avoid accidental starting. Make sure

snow thrower. To avoid serious injury, the operator and unit must be in a stable position while starting.

The following sequence must be followed correctly to start the unit.

1. Make sure the unit is plugged in.

2. Place the switch key into the switch key slot (Fig. 4) NOTE: The unit is designed to NOT start without the

switch key installed into the unit.

3. Press in and hold the red starter button (Fig. 5).

4. While holding the starter button, lift and hold the bail. Once the unit starts, release the start button.

NOTE: The unit will NOT start if the start button is not

pressed and held when the bail is lifted.

5. Hold the bail and begin operating the unit (Fig. 6).

STOPPING INSTRUCTIONS

1. Release hands from bail.

2. The starter button will pop out and unit will stop.

IF... not running the unit for long lengths of time or in

between uses, remove the switch key and keep in a safe place.

switc./,

Key Switch

KeySlot

Bail

Starter

Button

Fig. 6

OVERLOAD PROTECTION SWITCH

This unit is equipped with an overload protection switch to protect the circuit (that the unit is plugged into) from

short circuit overloads.

If the switch pops out:

1. Release the bail and allow the unit to stop and cool for a minute.

2. Press the overload switch to reset. Start unit according to the Starting Instructions and resume

operation (Fig. 5)

If the switch pops again shortly after the first time:

1. Allow the unit to cool for 15 to 30 minutes. Making sure to prevent accidental starts by removing the switch key.

2. After the unit has cooled, press the overload switch to reset. Start unit according to the Starting Instructions and resume operation.

If the switch does not stay in, or if it continues to pop out

during operation, take the unit to an authorized service dealer for repair.

OPERATING THE UNIT

1. Start the unit according to the Starting Instructions. The depth and weight of the snow governs the forward speed.

2. Push the unit so that it rides on the wheels and scraper.

3. Make sure the power cord is attached to the cord

retainer and rests on the guide bar. The power cord

should trail to the side of the operator.

Overload

Protection

Switch

Fig. 5

Discharge Direction Adjustment

Snow may be discharged to the left, straight forward, or to the right of the operator.

To change the direction, use the following instructions:

1. Release the bail to stop the rotor.

2. Firmly grasp the discharge directional control handle and pull it up. This releases the spring-loaded rod from the discharge direction slot and allows free movement (Fig. 7)

3. Turn the discharge directional control to the left, the center or the right, depending on which direction you want to throw the snow (Fig. 8).

NOTE: From the center position, the discharge directional

control turns approximately 45 degrees in either direction (left or right). Do not force it.

4. Release the discharge directional control so it fits into the slot to secure the desired position.

NOTE: Make sure the discharge directional control is

securely positioned in direction slot and cannot rotate freely.

5. Restart the unit according to the Starting Instructions.

Pull the DischargeDirectional Control

Upwards

Top View

Discharge snow

in FRONT

45° \_\

Discharge snow to

LEFTof operator

Fig. 8

Tips for Best Snow Throwing Results

• For the most efficient snow throwing, keep the vanes parallel and throw snow downwind.

• Slightly overlap each swath you make (Fig. 9).

, 45°

Dischargesnow to RIGHT of operator

Fig. 7

Fig. 9

Clearing a Clogger Discharge Chute

'_l WARNING: Using hands or any other body part

NOTE: Hand contact with rotating impeller inside the

To clear the chute:

1. Shut the unit off.

2. Wait 10 seconds to be sure the impeller blades have

come to a complete stop.

3. Always use an appropriate tool to clean out the

chute. Never use hands or other body parts.

to clean the chute while the unit is running can

cause sever injury.

discharge chute is the most common cause of injury associated with snow throwers. Never use hands or

any other body part to clean out the discharge chute.

SERVICING THE UNIT

Extreme care and knowledge of the system is required when servicing this unit. Service should be performed by qualified

service personnel only. Replacement parts for this unit must be identical to the parts they replace. Refer any repair to an authorized service dealer.

INSPECTING/REPLACING THE DRIVE BELT

When servicing the unit, use only original equipment manufacturer replacement parts. Inspect the drive belt once a year or every 50 hours of operation, whichever comes first, for wear. If the drive belt needs to be replaced, use the following

instructions.

Belt Tensioner

(Idler Arm)

Drive Pulley

I_ WARNING: To avoid serious personal injury,

Remove the flange lock nut from the belt case cover with a wrench or nut driver (Fig. 10).

Remove the seven (7) screws from the belt case cover using a #T20 Torx bit or flat blade screwdriver (Fig. 10).

I_ WARNING: To reduce the risk of electrical

Cover

Screws (7)

turn off the unit and allow it to cool. Unplug the unit before you perform any maintenance.

shock, replace the cover before connecting the unit to a power source.

Driven

Pulley

Fig. 11

5. Reinstall the cover with the seven (7) screws. To make installation easier, place the narrow part of the cover into

the recess of the housing. Install the top two screws, then push the rest of the cover down into the recess and over the rotor shaft. Torque all seven (7)screws to 18-23 inolb

(2.0-2.5 Nom).

6. Reinstall the flange lock nut. Torque the nut to

80-100 inolb (9.0-11.2 N°m).

NOTE: If the flange lock nut is damaged, do not replace it with

a standard nut. Replace only with an original equipment manufacturer replacement part.

Drive Pulley

Belt Tensioner

Belt

Flange Lock Nut

Fig. 10

3. Pull the belt tensioner (idler arm) away from the drive pulley. Remove the damaged or broken belt from the

driven pulley and drive pulley inside of the housing. Discard appropriately (Fig. 11).

4. Loop the new belt around the drive pulley and driven pulley (Fig. 11). Pull the belt tensioner (idler arm) away from the drive pulley to install the belt around the drive pulley.

NOTE: Make sure the washer is still in place on the driven

pulley shaft prior to reinstalling the belt case cover.

Drive Belt

Retainer

Driven

Pulley

Fig. 11a

WARNING: When refitting the belt back into the

main housing, be sure that the belt is to the right of

the Drive Belt Retainer. If the belt is placed to the

left, serious damage may occur.

REPLACING THE SCRAPER CLEANING

I_ ARNING: To avoid serious personal injury,

Use only original equipment manufacturer replacement parts.

1. Place the unit on the ground or on a work bench.

Position the unit so the vanes and rotor are facing up.

2. Beneath the rotor, locate the three (3) screws securing

the scraper to the housing. Remove them using a

#T20 Torx bit or flat blade screwdriver (Fig. 12).

3. Remove the scraper and discard it appropriately.

4. The new scraper will snap into place. Once in place,

attach it to the unit by reinstalling the three (3) screws.

Torque the screws to:

always turn your unit off and unplug it before you perform maintenance.

25-30 in°lb (2.8-3.3 N°m).

I i,iwA°°°oToavodseriouspersonan'u I

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.

TRANSPORTING

• Allow the motor to cool before transporting.

• Secure the unit while transporting.

• To move the unit, grasp it by the top and middle front handles (Fig. 13).

• If you are transporting the unit with the handles folded, be careful not to make contact and accidentally bend

the discharge directional control (Fig. 8). If you bend or

damage the control, you can no longer adjust the vanes.

alwaysturn your unit off and unplug it beforeyou cleanor service it.

Scraper

Fig. 12

NOTE: Check ALL bolts at frequent intervals for proper

tightness to be sure the unit is in good, safe

working condition.

STORAGE

• Allow the motor to cool before storing.

• Store the unit locked up to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

Fig. 13

CAUSE

Unitisunplugged Switchkeyisnotinstalled

Starterbuttonorbailwereimproperlyused Overloadprotectionswitchhaspoppedout

ACTION

Checkcordtomakesureitispluggedintoanelectricaloutlet Installswitchkeyintotheswitchkeyslot.

Pressinstarterbutton,holdit,andholdbail PushitinandfollowtheStarting Instructions

CAUSE

Beltisdamaged

CAUSE

Scraperisworn

Replace the belt, according to Inspecting/Replacing the

Driver Belt

Replace the scraper

ACTION

If further assistance is required, contact your authorized service dealer

Motor type ............................................................................................................................................................... A.C.,120 Volts Electric

Operating RPM .............................................................................................................................................................. up to 14,000 rpm

Ignition Switch ...................................................................................................................................................... Bail Lock Safety Button

Amperage .................................................................................................................................................................................... 8.5 amps

Overload Protection ................................................................................................................................................. 120V, 15 amp Breaker

Handles .................................................................................................................................................................................... Steel Tube

Approximate Unit Weight ..................................................................................................................................................... 20 Ibs. (9 kg.)

Snow Depth (maximum) ........................................................................................................................................ 6 inches (0.152 meters)

Cleared Path Width ............................................................................................................................................. 12 inches (0.318 meters)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

MANUFACTURER'S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC ("MTD") with respect to new merchandise purchased and used in the United States, its possessions and territories.

MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by MTD for use with the product(s) covered by this manual will void your warranty as to any resulting damage. This warranty is limited to ninety (90) days from the date of original

retail purchase for any MTD product that is used for rental or commercial purposes, or any other income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate the dealer in your area, please check for a listing in the Yellow Pages or contact the Customer Service Department of MTD LLC by calling 1-800-800-7310 or writing to P.O. Box 361131, Cleveland

OH 44136-0019 or if in Canada call 1-800-668-1238. Or visit our website at www.yardman.com. No product returned

directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of MTD LLC.

This limited warranty does not provide coverage in the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters. B. Wear items - Bump Knobs, Outer Spools, Cutting Line,

Inner Reels, Starter Pulley, Starter Ropes, Drive Belts.

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product shall bind MTD. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above. (Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the use or misuse or inability to use the

product. This limited warranty shall not extend to anyone other than

the original purchaser, original lessee or the person for whom

it was purchased as a gift.

How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state. To locate your nearest service dealer dial 1-800-800-7310

in the United States or 1-800-668-1238 in Canada.

C. MTD does not extend any warranty for products sold or

exported outside of the United States of America, its possessions and territories, except those sold through MTD's authorized channels of export distribution.

MTD reserves the right to change or improve the design of any MTD Product without assuming any obligation to modify

any product previously manufactured.

MTD LLC

P.O. Box 361131

Cleveland, OH 44136-0019

+ 30 hidden pages