MTD 24A-021H000 Owner’s Manual

Operator's Manual
Chipper Shredder
Model Series 020
Vacuum
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131
Cleveland, Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A. FORM NO. 770-10535D
(7/2003)
TABLEOFCONTENTS
Content Page
Important Safe Operation Practices .................................................................. 3
Assembling Your Chipper Shredder Vacuum .................................................... 5
Know Your Chipper Shredder Vacuum .............................................................. 7
Operating Your Chipper Shredder Vacuum ....................................................... 7
Maintaining Your Chipper Shredder Vacuum .................................................... 9
Troubleshooting ................................................................................................ 12
Parts List ........................................................................................................... 14
FINDINGMODELNUMBER
This Operator's Manual is an important part of your new chipper shredder vacuum. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. The information on the model plate is very important if you need help from our Customer Support Department or an
authorized dealer.
You can locate the model number by looking down at the rear of the chipper shredder vacuum. A sample
model plate is explained below. For future reference, please copy the model number and the serial number of
the equipment inthe space below.
f
Copy the model number here:
mwm m ==,,- ill CLEVELANDBH44136!
P. O. BOX 361131
__lWc_ 330-220-4683 |
,. www.mtdproducts.com 800-800-7318 J
Copy the serial number here:
ENGINEINFORMATION
The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual packed separately with your unit for more information.
CALLINGCUSTOMERSUPPORT
PleasedoNOTreturnthe unitto the retailer from whichit waspurchased,withoutfirstcontactingCustomerSupport.
Should you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department.
Call 1- (330) 220-4MTD (4683) or 1- (800)-800-7310 to reach a Customer Support representative. Please have your unit's model number and serial number ready when you call. See previous section to locate this information. You will be asked to enter the serial number in order to process your call.
SECTION1: IMPORTANTSAFEOPERATIONPRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could
endanger the personal safety and/or property of yourself and others. Read and follow all instructions in
this manual before attempting to operate this machine. Failure to comply with these instructions may
result in personal injury. When you see this symbol - heed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result inserious injury or death.
TRAINING
1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.
2. Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.
3. Never allow children under 16 years old to operate this machine. Children 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.
4. Never allow adults to operate this machine without proper instruction.
5. Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
6. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.
7. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate
fingers, hands, and feet.
8. Never attempt to unclog either the feed intake or discharge opening, remove or empty vacuum bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine.
PREPARATION
1. Thoroughly inspect the area where the equipment is to be used. Remove all rocks, bottles, cans, or
other foreign objects which could be picked up or thrown and cause personal injury or damage to the
machine.
2. Always wear safety glasses or safety goggles
during operation or while performing an adjustment or repair, to protect eyes. Thrown objects which
ricochet can cause serious injury to the eyes.
3. Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Loose fitting clothes or
jewelry can be caught in movable parts. Never
operate this machine in bare feet or sandals. Wear
leather work gloves when feeding material in the
chipper chute.
4. Before starting, check all bolts and screws for proper tightness to be sure the machine is in safe
working condition. Also, visually inspect machine for any damage at frequent intervals.
5. Maintain or replace safety and instructions labels, as necessary.
6. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.
a. Use only an approved gasoline container. b. Extinguish all cigarettes, cigars, pipes, and
other sources of ignition.
c. Neverfuel machine indoors. d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes
before refueling.
f. Never over fill fuel tank. Fill tank to no more
than 1/2 inch below bottom of filler neck to provide space for fuel expansion.
g. Replacegasolinecapandtightensecurely.
h. Ifgasolineisspilled,wipeitofftheengine
andequipment.Movemachinetoanother area.Wait5minutesbeforestartingthe engine.
i. Neverstorethemachineorfuelcontainer
insidewherethereisanopenflame,spark, orpilotlight(e.g.furnace,waterheater, spaceheater,clothesdryer,etc.)
j. Toreduceafirehazard,keepmachinefree
ofgrass,leaves,orotherdebrisbuild-up. Cleanupoilorfuelspillageandremoveany
fuelsoakeddebris.
k. Allowmachinetocoolatleast5minutes
beforestoring.
OPERATION
1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate
fingers, hands, and feet.
2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty
and free of all debris.
3. Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other
foreign objects which could cause personal injury
or damage to the machine.
4. If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:
a. Inspect for damage. b. Repair or replace any damaged parts. c. Check for any loose parts and tighten to
assure continued safe operation.
5. Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.
6. Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.
7. Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.
8. Never operate without vacuum bag and discharge chute properly attached to the machine. Never empty or change vacuum bag while the engine is running. Zippered end of vacuum bag must be kept closed at all times during operation.
9. Never operate without either the inlet nozzle or optional hose attachment properly attached to the
machine. Never attempt to attach or change either
attachment while the engine is running.
10. Keep all guards, deflectors and safety devices in
place and operating properly.
11. Keep your face and body back and to the side of the chipper chute while feeding material into the
machine to avoid accidental kickback injuries.
12. Never operate this machine without good visibility or light. Always be sure of your footing and keep a
firm hold on the handles.
13. Do not operate this machine on agravel surface.
14. Do not operate this machine while under the
influence of alcohol or drugs.
15. Muffler and engine become hot and can cause a
burn. Do not touch.
16. Never pick up or carry machine while the engine is
running.
MAINTENANCEANDSTORAGE
1. Never tamper with safety devices. Check their
proper operation regularly.
2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.
3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all
moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.
4. Do not change the engine governor settings or overspeed the engine. The governor controls the
maximum safe operating speed of the engine.
5. Maintain or replace safety and instruction labels, as necessary.
6. Follow this manual for safe loading, unloading,
transporting, and storage of this machine.
7. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.
8. Always refer to the operator's manual for proper instructions on off-season storage.
9. If the fuel tank has to be drained, do this outdoors.
10. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
_, ARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read,
understand and follow the warnings and instructions inthis manual and on the machine.
NOTE: Not all safety labels shown may apply to your model chipper shredder vacuum.
READ OPERATOR'S MANUAL.
KEEP HANDS OUT OF iNLET AND DISCHARGEOPENINGS WHILE MACHINE iS RUNNING. ROTATING BLADES ARE iNSiDE.
" TURN ENGINE OFF AND ALLOW iMPELLER TO COME TO COMPLETE STOP
BEFOREREMOVING BAG.
® DONOT A'R'EMPT TOCLEARA CLOG OR JAM WiTH THE ENGINE RUNNING. = DONOTOPERATEUNIT WffHOUT BAGOR OFnONAL BLOWER CHUTEiN PLACE,
DONOTSTANDOR WALKiN FRONTOFBLOWERCHUTEORNM ff ATBYSTANDERS,
OBJECTS THROWN OUT OF DISCHARGE CAN CAUSE PERSONAL iNJURY.
® DONOT OPERATE WHEN CHILDREN OR OTHERS ARE AROUND.
WEAR APPROVED SAFETY GLASSES.
TO AVOID SERIOUS iNJURY
STOP
SECTION2: ASSEMBLINGYOURCHIPPERSHREDDERVACUUM
IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine.
NOTE: Reference to right or left hand side of the chipper shredder vacuum is observed from the operating position.
LoosePartsInCarton(SeeFigure1)
Handle Assembly
Bag
Blower Chute (on models so equipped)
DisconnectingSparkPlugWire
Before setting up your chipper shredder vacuum, disconnect the spark plug wire from the spark plug and ground to a stud on the engine.
/
Blower Chute
Wing
Bag
Handle
Nuts
Screw
Figure 1
Loading...
+ 11 hidden pages