Page 1
$1.00
owners GUIDE
OUTDOOR POWER EQUIPMENT
for all seasons
LEAF
BLOWERS
IMPORTANT:
Read Safety Rules and
Instructions Carefully
Model Numbers
248-692-000
248-693-000
248-694-000
24695-8
Thank you for purchasing
an American-built product.
PRINTED IN U.S.A. FORM NO. 770-5209C
Page 2
NDEX
Safe Operation Practices.............................................. 3
Assembly Instructions................................................... 4
Operation...................................................................... 5
Adjustments.................................................................. 6
Instruí étions given with this symbol are
for pei sonal safety. Be sure you follow
A
them.
Maintenance and Lubrication
Off-Season Storage.............................................................. 6-
Trouble Shooting Chart.........................................................
Illustrated Parts
..................................................................
...............................................
6
8,9
à
àc
This unit is equipped with an internal combuslpon engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the enigne's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in_
effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available
through your nearest engine authorized servic e center.
WARNING
t
Page 3
IMPORTANT
is suggested that this manual be read in its entirety before attempting to assemble or operate. Keep this
manual in a safe place for future reference and for ordering replacement parts.
This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper
fuel and engine oil recommendations.
SAFE OPERATION PRACTICES FOR LEAF BLOWERS
1. Read this operating and service instructing manual
carefully. Be thoroughly familiar with the controls
and proper use of the power leaf blower.
2. Never allow children to operate this power
leaf blower.
3. Keep the area of operation clear of all persons,
particularly small children and pets.
4. Check fuel before starting engine. Do Not fill fuel
tank indoors, when engine is running, or while
engine is hot. Wipe off any spilled fuel before
starting engine.
■v5u^ Do Not change engine governor settings.
Do Not put hands near rotating parts for any
reason.
7. If the power leaf blower should start to vibrate
abnormally, stop the engine and check immediate
ly for the cause. Vibration is generally a warning
of trouble.
8. Before cleaning, repairing or inspecting make
certain ail moving parts have come to a complete
stop. Disconnect spark plug wire and keep wire
away from plug to prevent accidental starting.
Also keep throttle control lever in the stop
position.
9. if the power leaf blower should become blocked
with debris at any point, shut engine off and wait
until the impeller comes to a complete stop before
attempting to remove the.obstruction. Disconnect
spark plug wire to prevent accidental starting.
10. Check all bolts for tightness at frequent peroids.
11. Never store this power leaf blower with fuel in
the tank. Allow engine to cool before storing in
any enclosure.
12. Keep equipment free of debris when not in use.
13. Never operate this leaf blower unless impeller
guard and guard assembly are properly affixed in
their place.
14. Never change inlet nozzle or auxiliary hose
attachment when engine is running.
15. The manufacturer recommends that the operator
wear safety glasses or some other suitable eye
protection when operating this machine.
16. Exercise caution whenever operating leaf blower.
Do Not allow exhaust to be pointed in the
direction of persons.
17. No one should operate this unit while
intoxicated or while taking medication that impairs
the senses or reactions.
Page 4
FIGURE 1.
ASSEMBLY INSTRUCTIONS
NOTE
Vacuum hose attachment 247-204-000
comes with model 694. It is optional
equipment on all other models.
CONTENTS OF HARDWARE PACK:
(See Figure 1)
A (2) Carriage Bolts
B (2) Hand Knobs
C (1) Hex Sems Bolt
FIGURE 2.
PARTS IN CARTON (See Figure 2):
D (1) Upper Handle
E (1) Directional Discharge
NOTE
The right and left side of your leaf
blower is determined from operator's
position.
1. Remove the leaf blower, hardware pack and all
literature from the carton before discarding
carton.
USE THIS
HOLE ONLY
FIGURE 3.
2. Figure 3 shows lower handle. Upper hancfle
mounts in center hole only.
Page 5
3. Place the upper handle (D) over the lower handle,
lining up the holes. Secure with carriage bolts (A)
and hand knobs (B). See figure 4.
4. Slip end of directional discharge (E) over chute
opening. Secure in position with hex sems bolt
(C). See figure 5.
DIRECTIONAL
DISCHARGE (E)
FIGURE 5.
OPERATION
BEFORE STARTING ENGINE
Service engine with gas and oil. See engine manual
packed with leaf blower for complete instructions for
care and maintenenace of engine. READ DIREC
TIONS CAREFILLY.
TO START ENGINE
. Move choke lever on engine to choke position.
NOTE
A warm engine may not require
choking.
2. Move throttle control lever on engine to START
or ON position.
3. Crank engine by pulling recoil starter with a
quick, firm stroke. Do not pull out so far the rope
stops with a jerk. Do not allow rope and han
dle to snap back into place.
4. After two or three full firm pulls on recoil (or
as soon as engine fires, move choke control to
RUN position.
TO STOP ENGINE
1. To stop engine, move throttle control lever to
STOP position.
2. Disconnect spark plug wire and ground to
prevent accidental starting while equipment is
unattended.
Page 6
ADJUSTMENTS
ÂC WARNING \
Do Not make this adjustment or any
adjustment with the engine running.
Stop the engine, disconnect the spark
plug wire and ground plug wire to
engine block.
TWO-WAY AIR DISCHARGE
Your leaf blower is equipped with an adjustaale
chute deflector. Simply push down on handle pro\ ided and swing door towards the front or side as desirad.
See figure 6.
DIRECTIONAL
DISCHARGE
CARBURETOR ADJUSTMENT
WARNING
▲C
If any adjustments are made to the
engine while the engine is running
(e.g. carburetor), keep clear of all
moving parts. Be careful of heated
surfaces and muffler.
if carburetor needs adjustment to start or for opera
tion, see "Carburetor Adjustment" section of engine
manual.
MAINTENANCE AND LUBRICATION
Your leaf blower, like all machines with moving parts,
must receive care and maintenance. The following
tips, if used, will contribute many troublefree hours
to your blower.
1. Check oil level frequently. When changing oil,
make sure dirt and debris is cleaned off oil sump
before removing oil plug.
2. Keep blower clean, especially the engine and
engine air filter.
3. Check all nuts, bolts and screws occasionally to be
sure blower is in good operating condition.
4. The wheel bearings are pre-lubricated at the_
factory and should require no further attentio’
until blower is serviced. However, it is advisabk
to remove the wheels and apply a small amount
of light oil to each axle at least once a season.
FIGURE 6.
HEIGHT ADJUSTMENT
The height adjustment crank is located on the right
hand side of the leaf blower. See figure 7. Turn the
crank clockwise to raise the discharge chute. Turn the
crank counter-clockwise to lower.
OFF-SEASON STORAGE
If you are going to store your blower for any length
of time (30 days or longer), it is important that the
following steps be taken:
1. Drain the gas tank. Start the engine. Allow it to
run out of gas. Gasoline left in the engine will
leave gum deposits in the carburetor and gas tank.
2. Clean engine of all foreign matter.
3. Lubricate cylinder by removing the spark plug
and pour in one ounce of clean lubricating oil
through the spark plug hole into the cylinder.
Crank engine slowly to spread oil and replace
spark plug. To start after storage, remove spark
plug and rotate engine with starter to remove
excess oil.
NOTE
When storing any type of power
equipment in an unventilated or metal
storage shed, care should be taken to
rust proof the equipment. Using a
light oil or silicone, coat the equip
ment, especially springs and bearings.
Page 7
TROUBLE SHOOTING CHART
PROBLEM CAUSE
1. Excessive
vibration.
2. Engine fails
to start.
3. Hard starting
or loss of power.
4. Engine over
heats.
NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer.
A. Bent crankshaft. A. Replace crankshaft (should be done by an authorized service
B. Vane plate out of balance. B. Replace vane plate.
A. Check fuel tank for gas. A. Fill tank if empty.
B. Spark plug lead wire
disconnected.
C. Faulty spark plug.
A. Spark plug wire loose.
B. Dirty air cleaner.
A. Carburetor not adjusted
properly.
B. Air flow restricted. B. Remove blower housing on engine and clean as described in the
C. Engine oil level low. C. Fill crankcase with the proper oil.
dealer).
B. Connect lead wire.
C. Clean, adjust gap or replace. See engine manual.
A. Connect and tighten spark plug wire.
B. Clean air cleaner as described in engine manual.
A. Adjust carburetor. See engine manual.
engine manual.
REMEDY
Page 8
Models 692, 693, 694 and 24695
PARTS LIST FOR LEAF BLOi/VER MODELS 692, 693, 694 and 24695
REF.
NO.
1
PART NO.
749-0479
2 726-0100
3 720-0171
736-0117 Fl.-Wash. .385" I.D. x
4
COLOR
CODE
DESCRIPTION
Upper Handle
Push Nut 3/8" Rod 19
Crank Knob
.62" O.D.
714-0114 Sq. Key 1/4" x 2.0" Lg
5
710-0442 Hex Bolt 5/16-18 X 1.50"
6
Lg.*
7 16453
Engine Mounting Frame
Ass'y.
736-0119 L.-Wash. 5/16" I.D.*
8
9 712-0267
736-0187 Fl.-Wash. .63"'I.D. x 1.:
10
Hex Nut 5/16-18 Thd.*
O.D.
11 714-0115
Cotter Pin 1/8" Dia. x
1.0" Lg.
12
712-0206
13 736-0921
14
734-1036 Swivel Caster Wheel 5"
Hex Nut 1/2-13 Thd.*
L.-Wash. 1/2" I.D.*
Dia. X 1.25"
16273
15
Caster Arm Ass'y.
16 710-0726 Hex Wash. Hd. "AB"
TapScr. 5/16"x.75" t
17 14529 Caster Arm Bracket
NEW
PART
*
5"
g.
REF.
NO.
18
PART NO.
747-0542
734-1035 Wheel Ass'y. Comp. 12" x
734-1184
734-1185
734-1183 Rim Only (For 734-1184
20 736-0159
21 710-0170
22 736-0162
23
24
25
26
27
736-0300
750-0528
736-0169
712-0354
710-0118
28 711-0797
29 09966
30
710-0487
31 749-0481
COLOR
CODE
DESCRIPTION
Height Adjustment Crank
3" (Plastic) (IncI,
Bearings)
Wheel Ass'y. Comp. 10.5"
X 4" (Steel)
Tire Only (For 734-1184
Wheel)
Wheel
Fl.-Wash. 34" I.D. x .87"
O.D.
Hex Locking Bolt 5/16-24
X .62" Lg.
Fl.-Wash. (692 Only)
Fl.-Wash. .38" I.D. x.57" O.D.
Spacer .382" I.D. x .50"
O.D. X .180" Lg,
L.-Wash. 3/8" I.D.*
Hex Nut 3/8-8 Thd.
Hex Bolt 5/16-18 X .75" Lg
Ferrule
Hand Knob
Carriage Bolt 5/16^18 x 2.0
■-y-
Lower Handle
NEW
PART
N
N
*
N '
Page 9
Models 692, 693, 694 and 24695
PARTS LIST FOR LEAF BLOWER MODELS 692, 693, 694 and 24695
REF.
NO.
PART
NO.
COLOR
CODE
DESCRIPTION
NEW
PARI
REF.
NO.
PART
NO.
COLOR
CODE
DESCRIPTION
1 14539 Engine Housing Brace Ass'y- 14 711-0758 Hex Shoulder Nut .50" I.D.
2
710-0600
Hex Self Tap Scr. 5/16" x .50" 15
Lg.
710-0118
3
736-0119 L.-Wash. 5/16" I.D.*
4
14541 Right Angle Bracket
5
710-0627
6
7 710-0260
Hex Bolt 5/16-18 X.75" Lg.*
Hex Locking Bolt 5/16-24 x.75
Carriage Bolt 5/16-18 x .62"
Lg.*
8 14479 - 638 Directional Discharge Ass'y-
11 736-0119
L.-Wash. 5/16" I.D.*
12 712-0267 Hex Nut 5/16-18 Thd.*
731-0608 Blower Guard
13
*For faster service obtain standard nuts, bolts and washers locally. If these items cannot be
obtained locally, order part number and size as shown on parts list.
638-MTD Red
621—Brilliant Fire Mist (24695)
The engine is not under warranty by the leaf blower manufacturer. If repairs or service is needed on the
engine, please contact your nearest authorized engine service outlet. Check the "Yellow Pages" of your
telephone book under "Engines - Gasoline".
When ordering parts if color or finish is important, use color code shown at left,
[i.e. (part no.)—638 for MTD Red Finish]
14563 - 638
710-0191
16
17 736-0217 L.-Wash. 3/8" I.D. HD.
18
14536 - 638
19
1
14496 - 638
22 710-0259 Hex Sems Bolt 5/16-18 x .62"
23 736-0242
24
720-0170
Nozzle Plate Ass'y.
Hex Bolt 3/8-24 X 1.25" Lg.*
Air Vane Plate Ass'y.
Blower Housing Ass'y. - Comp.
Lg.*
Belleville Wash. 34" I.D. x .87"
O.D.
3-Arm Thumb Scr. 5/16-18 x
.75" Lg.
Find It Fast
InThs
yellow Pages
NEW
PART
Page 10
Page 11
Page 12
REPLACEMENT PARTS • P.O. JOX 36900 • CLEVELAND, OHIO 44136
Loading...