MTB Cameras MTB-7400Q User Manual
To reduce the risk of electric shock do not remove cover(or back)
No user serviceable parts inside. Refer servicing to qualified service personnel.
Design and specification are subject to change withoutnotice.
The exclamation point within an equilateral triangle is intended toal ert
the user to the presence of important operatingandmaintenance
(servicing) instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol,within an equilateral
triangle,is intended to alert the user to the presenceofuninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
USER GUIDE
7" Wide TFT LCD Color Quad System
MTB-7400Q
-1-
Contents
CAMERA
SUN SHIELD WITH PROTECTION RUBBER (PATENT PENDING)
MONITOR
ACCESSORIES
STAND BRACKET KIT / SUCTION CUP KIT (OPTIONAL)
BUILT- IN REMOTE RECEIVER
BUILT- IN SPEAKER (1W)
RUBBER TOUCH NEUTRAL BLACK
AUTOMATIC SCREEN-ON (SIGNAL FROM "R"GEAR)
NOR./ MIR.& UP / DOWN IMAGE REVERSING
SHUTTER CAMERA / REAR VIEW CAMERA
SIDE VIEW CAMERA / HEATER CAMERA
WIDE SCREEN(16:9)
181(W) x 122(H) x 24(D)mm (7.13x4.8
x
0.94
Inch)
DC 10V ~
30
V(Freevoltage)
POWER & CAMERAINPUT CABLE /
WATERPROOF / SUN SHIELD / IR SENSOR / NORMAL / MIRROR / HEATER (OPTIONAL)
DIMMER
REMOTE CONTROL
HOUSING
RESOLUTION
DISPLAY MODE
4 CAMERAS INPUT
SCREEN MODE
BRIGHTNESS
AUDIO OUTPUT
DIMENSION
POWER SOURCE
CAR REAR VIEW
SIZE
SPECIFICATION
BUILT- IN CDS SENSOR Automatic/Manual
1440 (W) x 234(H) Pixels
500 cd / m
OPERATING TEMP.
WEIGHT
-30 C ~ 85 C / -22 F ~ +185 F
STORAGING TEMP.
-20 C ~ 70 C / - 4 F ~ +158 F
450 (g)
VIEW ANGLE
TOP: 40 BOTTOM: 60 LEFT: 60 RIGHT:60
2
°
°
°
°
°
°
°
°
-2-
Checking the main unit and supplied accessories
II
Features / Technical Specications
I
MTB-7400Q (QUAD MONITOR)
Operations
III
4-14
Checking the main unit and supplied accessories
II
2-3
Features / Technical Specications
I
1
Using MTB-7400Q in the car
IV
16
SystemWiring
VI
16
Sun Shield
V
17
MTB-80 Rear View Camera
VII
19
X
w
zwsp{
jhUzls
tlu|
kpt
}vs|tlG
}vs|tlG
jGz
Y
Z
[
]
^
_
\
X
Y
]
^
_
Z
[
\
GOP
OP
°
°
° °
-3-
z h
Power&Camera
Input Cable
Stand Bracket Kit
Rubber Sun Shield
User’s Guide
-4-
- If the Menu Key is pressed at the POWER ON mode, the OSD appears
in the monitor and the selected letters on OSD is classified in a different color.
- If pressing of the Menu Key is repeated in OSD state, the display
is circled in regular sequence of FUNCTION PICTURE NOR / MIR
Clear of OSD.
the sequence will be as below without the CAMERA OSD.
FUNCTION
PICTURE Clear of OSD.
- When POWER OFF (which means STANDBY state), the LED lights
in RED color.
- When POWER OFF, the R gear and the WINKERS (Left / Right) and
the TACHOMETER make that the linked each camera operates for displaying
its field of view on the monitor.
- After POWER ON, the LED in RED color is turned off and all
LEDs light in GREEN color.
- After POWER ON, the LAST CHANNEL saved from its last operation
is displayed on the monitor.
set-up (Factory Default).
- DIRECT POWER ON Subject To LAST POWER SAVE Mode:
* After starting up the car engine, the monitor turns on automatically
at the same time and the monitor starts displaying of the views from the
(1) If the car engine had been turned off at the POWER ON state of monitor,
the LAST POWER SAVE mode is ON (Factory Recommendation).
(2) If the car engine had been turned off after the POWER OFF of monitor,
the LAST POWER SAVE mode is OFF.
cameras if the LAST POWER SAVE mode is ON.
Operations
III
Accessories
1 Power Key
2 Menu Key
A
Menu Control Keys
FUNCTION
LANGUAGE ENGLISH
DIRECTION
DIMMER
RESET
ENTER
SYSTEM
0/180
AUTO/OFF
NTSC/PAL
PICTURE
CONTRAST
BRIGHT
COLOR
TINT
50 (0-100)
50 (0-100)
50 (0-100)
50 (0-100)
NOR/MIR
NOR/MIR
NOR/MIR
Heavy Duty Bracket Kit
NOR / MIR
CA1
CA2
CA3
CA4
NOR/MIR
NOR/MIR
NOR/MIR
NOR/MIR
-5-
50
VOLUME
[UGGjG|GVGkGr
- The brightness is adjusted manually at the POWER ON mode,
if DIMMER is selected in OSD set-up.
Pressing of DIMMER Key in this condition makes the change
of brightness responding on every manual operation of the Key.
- If pressing of the QUAD Key is repeated at the POWER ON mode, the display
is revolved in sequence of SPLIT
PIP TRIPLE
QUAD.
- In OSD state, this QUAD Key is in use of moving a cursor to
downward as well.
- If pressing of the CA.SEL Key is repeated at the POWER ON mode,
the CHANNEL is changed in regular sequence of
CH1
CH2
CH3 CH4
- In OSD state, pressing of these VOLUME Up / Down KEYS makes
the selected function to be adjusted and changed its status to new setup.
- Pressing of these VOLUME Up / Down KEYS at POWER ON mode makes
that the audio volume of the monitor is increased and/or decreased.
VOLUME Down KEY: To decrease the VOLUME
VOLUME Up KEY: To increase the VOLUME
Adjustable volume range from 0 to 100 (0 ~ 100)
Factory Default: 50
Language : 6 Languages
ENGLISH, GERMAN, FRENCH, ITALIAN,
SPANISH, DUTCH
- Locate the cursor at LANGUAGE by
CHANNEL and/or QUAD keys.
- Select the desired language by VOLUME Up/Down Keys.
- Factory default is ENGLISH.
-6-
SYSTEM
- Locate the cursor at SYSTEM by SPLIT and/or CA.SEL Keys.
- Select the proper system in your region by VOLUME Up/Down Keys.
- Factory default is PAL.
DIRECTION
- Locate the cursor at DIRECTION by SPLIT and/or CA.SEL Keys.
- Select the desired direction by VOLUME Up/Down Keys.
- 0 : Normal Screen (Factory Default)
- 180 : Shifted Screen to 180°reversely.
DIMMER SELECT KEY
- Locate the cursor at SELECT KEY by SPLIT and/or CA.SEL Keys.
- Select DIM by VOLUME Up/Down Keys.
- DIM : Release AUTO DIMMER and adjust the brightness manually by
pressing of DIMMER Key.
3 DIMMER Key
4 SPLIT(Up) Key
5 CA.SEL(down) Key
6
VOLUME Up / Down Key
1 FUNCTION
B
How to set up the functions of the Menu on OSD
FUNCTION
LANGUAGE
ENGLISH
DIRECTION
DIMMER AUTO/OFF
RESET
ENTER
SYSTEM
0 /180
NTSC/PAL
7
.
Loading...