M-system R5T-RS Instruction Manual

INSTRUCTION MANUAL

RTD INPUT MODULE

(screw terminal block)

BEFORE USE ....

Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

RTD input module ...............................................................(1)

■ MODEL NO.

Confirm Model No. marking on the product to be exactly
what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.

MODEL

R5T-RS

POINTS OF CAUTION

■ CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument
panel of a metal enclosure.

• The actual installation environments such as panel con­figurations, connected devices, connected wires, may af­fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform­ity.

■ HOT INSERTION/REMOVAL OF MODULES

• Removing or replacing modules does not affect other mod­ules on the same backplane. It is possible to replace them
without removing the power supply. However, replacing
multiple modules at once may greatly change line voltage
levels. We recommend that you replace them one by one.

■ GENERAL PRECAUTIONS

• DO NOT set the switches while the power is supplied.
The switches are used only for maintenance without the
power.

■ ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.

• Do not install the unit where it is subjected to continu­ous vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.

■ WIRING

• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).

• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is sup­plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.

INSTALLATION

Use the Installation Base (model: R5-BS).

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-6115 Rev.3 P. 1 / 3

COMPONENT IDENTIFICATION

R5T-RS

■ SIDE VIEW ■ FRONT VIEW

Function

12345678

Burnout

RTD

Temp. Unit

ON

RUN

RUN LED

4

65

1

32

■ STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.

■ SIDE DIP SW

(*) Factory setting

• RTD Type: SW1, 2, 3, 4

SW

1 2 3 4

RTD

ON OFF ON OFF Cu 10 @ 25°C

OFF OFF OFF OFF Cu 50

OFF OFF OFF ON JPt 100 (JIS ’89)

• Temperature Unit: SW5, 6

SW

5 6

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

TEMP. UNIT

ON OFF OFF OFF Pt 100 (JIS ’89)

OFF ON OFF OFF Pt 100 (JIS ’97, IEC) (*)

OFF ON ON OFF Pt 1000

ON ON OFF OFF Pt 50 Ω (JIS ’81)

OFF OFF ON OFF Ni 100

ON ON ON OFF Ni 508.4 Ω

• Burnout: SW7, 8

SW

BURNOUT7 8

INPUT 1 INPUT 2

OFF OFF Downscale

ON ON Upscale (*)

PC CONFIGURATOR

With configurator software, settings shown below are available.
Refer to the software manual of R5CON for detailed operation.

■ CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to [phone]

Bias [Zero Adj.] -320.00 to +320.00 0.00

Gain [Span Adj.] -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

■ CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit No check mark: Limits to the scaling values equivalent to -15 % to

+115 %.

Check-marked: Limits within Zero Scale to Full Scale.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

No check mark

EM-6115 Rev.3 P. 2 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■ EXTERNAL DIMENSIONS unit: mm (inch)

R5T-RS

18 (.71)

(.22)

4

90 (3.54) 5.6

65

1

32

■ CONNECTION DIAGRAM

RTD

INPUT 1

RTD

INPUT 2

1

A

2

B

3

B

4

A

5

B

6

B

8.2 (.32)

6–M3.5
TERMINAL
SCREWS

7.2 (.28)

38.5 (1.52) 98.5 (3.88)

INTERNAL BUS A

INTERNAL BUS B*

INTERNAL
POWER

BUS CONNECTOR

LOCKING CLAMP

TERMINAL COVER

POSITIONING GUIDE

WIRING INSTRUCTIONS

■ SCREW TERMINAL

Torque: 0.8 N·m

*For dual redundant communication.
Note: The section enclosed by broken line is with 2-ch. option.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-6115 Rev.3 P. 3 / 3