M SYSTEM 0000003 User Manual

INSTRUCTION MANUAL

WIRELESS I/O UNIT

(

Modbus-RTU Transparent 900MHz Band Wireless Device (Child device),

Built-in I/O, Contact Inputs 2 points, NPN Transistor Output 2 points

BEFORE USE ....

Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

Wireless I/O unit .................................................................(1)

Antenna ...............................................................................(1)

■ MODEL NO.

Confirm Model No. marking on the product to be exactly
what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when
you use this product, including installation, connection,
hardware setting, and basic maintenance procedures.
For information on the introduction of wireless device, re­fer to the 900MHz band wireless device operating manual
(EM-9085).

•Attachment of rooftop antenna; There is a magnet on the
bottom face which allows you to attach the antenna on
a metal box and such. To obtain optimum performance
from the antenna, attach on a metal plate (recommended
dimension: 500 mm × 500 mm or more). However, in the
case of connecting FE1 to a metal plate, the isolation be­tween FE1 and antenna connector will be lost. Tighten
the connector with a specified torque (0.9 N∙m). As a
guide, finger-tighten it until the connector stops, and then
rotate it 10 to 15 degrees with a wrench. Do not force the
cable to bend less than acceptable radius of 3 cm.

•Using 7.5 m coaxial cable (model: CX-SAC0SAD0Q0750)
(OKI) for extension decreases transmission distance.

)

MODEL

WL40W1F-DAC4A

Connector

POINTS OF CAUTION

■ POWER INPUT RATING & OPERATIONAL RANGE

•Locate the power input rating marked on the product and
confirm its operational range as indicated below:

24 V DC rating: 24 V ±10%, ≤ 70 mA
12 V DC rating: 12 V ±10%, ≤ 130 mA

■ GENERAL PRECAUTIONS

•Before you remove the unit or mount it, turn off the power
supply for safety.

■ ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufficient
ventilation.

•Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.

•Attach the antenna to the unit.

•Attachment and adjustment of sleeve antenna; Loosen

the connector (See the top-right figure.), and rotate the
antenna. Holding the antenna vertical, tighten the con­nector by hand.

•Make sure to fix the antenna firmly.

■ WIRING

•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).

•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.

■ AND ....

•The unit is designed to function as soon as power is sup­plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.

CAUTION REGARDING RADIO FREQUENCY

■ FCC NOTICE

•This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, in­cluding interference that may cause undesired operation.

■ FCC CAUTION

•Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s au­thority to operate the equipment.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 1 / 8

WL40W1F-DAC4A

■ NOTE

•This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accord­ance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to cor­rect the interference at his own expense.

•This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.

COMPONENT IDENTIFICATION

■ FRONT VIEW

Status Indicator LED

Power
920Link
920Run

920ERR

■ FCC RF EXPOSURE INFORMATION

•This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure Guide­lines. This equipment should be installed and operated
keeping the radiator at least 20cm or more away from
person’s body.

FCC ID : 2AOTF-0000003
Contains FCC ID: 2AKGW-1TD3016A1

Antenna Connector

DI1

DI2
DO1
DO2

Contact input/Transistor output
Indicator LED

Maintenance Connector

Configuration Jack

Connector for Power Input

＊

Power input defers depending on the power input code you select.

＊

CFG2

CFG1

24V

0V

NC

NC

FE1

DI1A
DI1B
DI2A
DI2B
NC

Contact Input Connector

V+
V­DO1
DO2
NC

Transistor Output Connector

■ STATUS INDICATOR LED

ID STAT U S COLOR FUNCTION

Power ON Green Power is on.
920Link ON Green Wireless: coordinator is connected

0.5 Hz blinking Green Wireless: coordinator connection is in process

Blinking twice per second Green Wireless: start-up error
920Run ON Green Wireless: normal communication
920ERR ON Red No detour

Blinking Red Network authentication failure

■ CONTACT INPUT/TRANSISTOR OUTPUT STATUS INDICATOR LED

ID STAT U S COLOR FUNCTION

DI1/DI2 ON Green ON

OFF – OFF

DO1/DO2 ON Green ON

OFF – OFF

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 2 / 8

■ TERMINAL ASSIGNMENTS

• Connector for power input

Unit side connector: MSTBV2,5/5-GF-5,08AU (Phoenix Contact)
Cable side connector: TFKC2,5/5-STF-5,08AU (Phoenix Contact)

• Power input code: R (24 V DC) • Power input code: S (12 V DC)

24V

NC
NC

FE1

ID FUNCTION

24V Power input 24 V 12V Power input 12 V

0V

0V Power input 0 V 0V Power input 0 V

NC Not used NC Not used

12V

NC
NC

FE1

0V

ID FUNCTION

NC Not used NC Not used

FE1 Power input earth FE1 Power input earth

• Contact input connector

Unit side connector: MC1,5/5-GF-3,5 (Phoenix Contact)
Cable side connector: FMC1,5/5-STF-3,5 (Phoenix Contact)

ID FUNCTION

DI1A
DI1B
DI2A
DI2B
NC

DI1A Contact input 1A
DI1B Contact input 1B
DI2A Contact input 2A
DI2B Contact input 2B

NC Not used

WL40W1F-DAC4A

• Transistor output connector

Unit side connector: MC1,5/5-GF-3,5 (Phoenix Contact)
Cable side connector: FMC1,5/5-STF-3,5 (Phoenix Contact)

ID FUNCTION

V+
V­DO1
DO2
NC

V+ External excitation +

V– External excitation –
DO1 NPN transistor output 1
DO2 NPN transistor output 2

NC Not used

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 3 / 8

WL40W1F-DAC4A

CONFIGURATOR SOFTWARE SETTING

With configurator software, settings shown below are available.
Refer to the users manual of W920FCFG for detailed operation.

■ WIRELESS SETTING

ITEM SETTING RANGE DEFAULT

Preferred PAN ID (group number) 0000 – FFFE (hexadecimal, 4 digits) 0000
Radio channel number 1 – 43 (selectable up to 10 channels) None
Short address 0000 – FFFD (hexadecimal, 4 digits) 0000
Network name English one-byte characters within 16 characters

(one-byte space, “-”, “_”, “.”, “@” are usable.)

Encryption key 0000...0 – FFFF...F

(hexadecimal, 32 digits)
Transmitter power output 0.16mW / 1mW / 20mW 20mW
Low-speed moving mode No / Yes No
Device type in a network,

Number of devices in a network

Set network quality Standard (recommended) /

Network join mode V3-compatible mode / Fast join mode V3-compatible mode
Fixed route No / Yes No
Destination short address 0000 – FFFD (hexadecimal, 4 digits) 0000
Temporary detour No / Yes Yes
Packet filtering None / Yes (polling type) Yes (polling type)
Filter timeout on polling 1.0 – 60.0 (sec.) 1.0 (sec.)
920Run timeout 1.0 – 60.0 (sec.) 3.0 (sec.)
Modbus node address 1 – 247 1
Retry times before route switching Once / Twice / Three times Three times

* For version confirmation of communication module, refer to the users manual of W920FCFG.

Child (fixed), 1 to 30 devices /

Child (fixed), 31 to 60 devices /

Child (fixed), 61 to 100 devices /

Child (fixed) + child (moving)

Frequency of route switching and delay (higher) /

Frequency of route switching and delay (highest)

Blank

0000...0

Child (fixed), 1 to 30 devices

Standard (recommended)

■ TRANSISTOR OUTPUT SETTING

ITEM SETTING RANGE DEFAULT

Output status at time of
920Run communication disconnect

Hold/Clear Hold

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 4 / 8

INSTALLATION

■ DIN RAIL MOUNTING

A) Hang the upper hook at the back of the unit on the DIN

rail.

B) Push the lower part of the unit to fit in the DIN rail.

WL40W1F-DAC4A

■ DEMOUNTING

A) Pull down the DIN rail adaptor using a minus screw-

driver.
B) Pull out the lower part of the unit.
C) Remove the upper part from the DIN rail.

B

A

C

B

A

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 5 / 8

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■ EXTERNAL DIMENSIONS unit: mm (inch)

● WITH SLEEVE ANTENNA

[R165(6.50)]

[260 (10.24)]

WL40W1F-DAC4A

[155 (6.10)]

DIN RAIL
35mm wide

105 (4.13)

5 (.20)

60 (2.36)

● WITH ROOFTOP ANTENNA

[200 (7.87)]

80 (3.15)

36 (1.42)

3 (0.12) dia.

1.2 (.05) dia.

(1.06)

8 (.31) Hex.

approx. 2500 (98.4)27 dia.

107 (4.21) 3 (.12)45 (1.77)

DIN RAIL
35mm wide

(.79)

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

107 (4.21) 3(.12)20

EM-9083 P. 6 / 8

■ CONNECTION DIAGRAM

WL40W1F-DAC4A

Antenna Connector

Maintenance Connector

Configuration Jack

INPUT 1

USB Connector

Jack

DI1A

DI1B

DI2A

INPUT 2

DI2B

NC

＊ Power input defers depending on the power input code you select.

• Input Connection Example

PNP connection NPN connection

+−

DI1B

+−

DI1A

+−

DI2B

+−

DI1B

DI1A

DI2B

＊

24V

Power Input

0V

NC

NC

FE1

EXCITATION +

V+

EXCITATION –

V–

OUTPUT 1

DO1

OUTPUT 2

DO2

NC

• Output Connection Example

V+

−+

V–

DO1

DO2

DI2A

DI2A

WIRING INSTRUCTIONS

■ TENSION CLAMP (FRONT TWIN CONNECTION) FOR POWER INPUT

Applicable wire size: 0.2 to 2.5 mm
Stripped length: 10 mm
Recommended terminals:

AI0,25-10YE 0.25 mm
AI0,34-10TQ 0.34 mm
AI0,5-10WH 0.5 mm
AI0,75-10GY 0.75 mm
AI1-10RD 1.0 mm
AI1,5-10BK 1.5 mm
AI2,5-10BU 2.5 mm

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

■ SEPARABLE TENSION CLAMP TERMINAL FOR INPUT/OUTPUT

Applicable wire size: 0.2 to 1.5 mm
Stripped length: 10 mm
Recommended terminals:

AI0,25-10YE 0.25 mm
AI0,34-10TQ 0.34 mm
AI0,5-10WH 0.5 mm
AI0,75-10GY 0.75 mm

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

(Phoenix Contact)

2

2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 7 / 8

MODBUS FUNCTION CODE

Modbus function codes are shown below.

■ DATA AND CONTROL FUNCTION

CODE NAME

01 Read Coil Status Digital output from the slave (read / write)
02 Read Input Status Status of digital inputs to the slave (read only)
03 Read Holding Registers General purpose register within the slave (read / write)
04 Read Input Registers Collected data from the field by the slave (read only)
05 Force Single Coil Digital output from the slave (read / write)
06 Preset Single Registers General purpose register within the slave (read / write)
15 Force Multiple Coils Digital output from the slave (read / write)
16 Preset Multiple Registers General purpose register within the slave (read / write)

■ EXCEPTION CODE

CODE NAME

01 Illegal Function Function code is not allowable for the slave
02 Illegal Data Address Address is not available within the slave
03 Illegal Data Value Data is not valid for the function
04 Slave Device Failure
05 Acknowledge
06 Slave Device Busy
07 Negative Acknowledge

WL40W1F-DAC4A

MODBUS I/O ASSIGNMENT

ADDRESS DATA TYPE DATA

Coil (0X) 1, 2 Digital Output 1, 2

3 – 16 Reserved (unused)

Input (1X) 1, 2 Digital Output 1, 2

3 – 16 Reserved (unused)

Input Register (3X) 1 – 16 – Reserved (unused)

Holding Register (4X) 1 – 16 – Reserved (unused)

Note: DO NOT access addresses other than mentioned above. Such access may cause problems such as inadequate operation.

I/O DATA DESCRIPTIONS

■ CONTACT DATA (1 BIT)

Contact input data and transistor output data are indicated each by 1 bit.
0: OFF
1: ON

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]

EM-9083 P. 8 / 8