MSTRONIC MSE PSE-SW3G User Manual
USER’S MANUAL
MSTRONIC CO., LTD.
MSE PSE-SW3G
3 Port PoE Switch & Extender
(Repeat Ethernet and PoE)
User’s Manual
MSE PSE-SW3 series
MSTRONIC CO., LTD.
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators.......................................................................................
Power Wiring ........................................................................................
Ethernet Port Wiring..............................................................................
PD Port Wiring......................................................................................
Network Application……………………………………............................
3. Model Information...........................................................
4. Technical Specification........................................................
3
3
3
5
8
10
11
12
13
User’s Manual
MSE PSE-SW3 series
MSTRONIC CO., LTD.
3
1. General Information
The PoE (Power Over Ethernet) Switch family provide two 10M/100M/1000M TX ports with PoE
PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It allow powered
from PoE power souring equipment (PSE) and deliver power to PoE powered device (PD), which is
compliant with IEEE802.3af and IEEE802.3at standard to receiver and deliver both of Ethernet data
and DC power through the traditional UTP or STP cable. The PoE Switch can extend Ethernet data
and DC power up to 200 meters. This manual will help you install and maintain the PoE switch.
Installation of the PoE switch is very easy and you will begin to operate as soon as you are powered
up.
2. Hardware Description
*LED Indicator
There are 8 LEDs on the PoE switch to indicate the status of power and signal. The following
section describes the functions of each LED indicator.
Front panel detail
User’s Manual
MSE PSE-SW3 series
MSTRONIC CO., LTD.
4
*POWER LED
LED
STATUS
Description
Power
Green
LED ON when power input (DC IN on
rear panel or port UP LINK on front
panel) has valid power supplied.
Red
The indicator only been used on
PSE-SW3G11CN, LED ON when the
following warning condition happened.
*Power input under voltage (Vin<10V)
*Power input over voltage (Vin>59V)
*PoE over current (2A/per port)
the indicator is unused on
PSE-SW3G44DN and PSE-SW3G42CN.
Off No power supplied.
*SWITCH LED (the right indicator on RJ45)
LED STATUS Description
P1,P2&UP LINK
Link/Act
Green
A network device is detected (1000Mbps),
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 1000Mbps.
Yellow A network device is detected (10Mbps or
100Mbps), but no communication activity
is detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off No device is detected.
User’s Manual
MSE PSE-SW3 series
MSTRONIC CO., LTD.
5
*PoE LED (the left indicator on RJ45)
P1,P2
PoE
Yellow
A valid Powered Device (PD) is detected
and delivering power on this port.
Off
No PD is detected on this port.
UP LINK
PoE
Yellow
Powered via all 4 data pairs.
Yellow
Blanking
Powered via 2 data pairs. (1,2,3,6 or 4,5,7,8
are all acceptable).
Off No power is detected on this port.
*Power wiring
The PoE switch family includes 3 models, be used for 2 different ranges of input voltage as,
full range voltage (12 to 57VDC) (P/N: PSE-SW3G11CN)
48VDC typical (42 to 57VDC) (P/N: PSE-SW3G44DN & PSE-SW3G42CN)
48VDC typical switches allow powered by another PoE source (42~57VDC) on port UP LINK.
For PoE operation, make sure your power supply may offer at least 40W for 2x 802.3af PoE port, or
80W for 4x 802.3at PoE port.
If powered on rear terminal, please make sure the input current don’t over 10A, if powered on port
UP LINK, make sure the input current don’t over 2Amp.
The port 1&2 will deliver DC power over the Ethernet cable, the connection as:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
Loading...