MSTRONIC DIN-SW5G44x4 User Manual
USER’S MANUAL
MSTRONIC CO., LTD.
DIN-SW5G44x4
5 Port PoE Switch & Extender
(Repeat Ethernet and PoE)
User’s Manual
DIN-SW5G44x4 series
MSTRONIC CO., LTD.
2
1. General Information
The DIN-SW5G PoE (Power Over Ethernet) Switch family provides four 10M/100M/1000M TX
ports with PoE PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It
accepts power from PoE power souring equipment (PSE) and delivers power to PoE powered
device (PD), which are compliant with IEEE802.3af and IEEE802.3at standard to receive and
deliver both Ethernet data and DC power through the traditional UTP or STP cable. The PoE
Switch can extend Ethernet data and DC power up to 200 meters.
2. Hardware Description
*LED Indicator
There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following
section describes the functions of each LED indicator.
Front panel detail
User’s Manual
DIN-SW5G44x4 series
MSTRONIC CO., LTD.
3
*POWER LED
LED
STATUS
Description
Power
Green
LED ON when power input (DC IN on
top panel or UPLINK on front panel) has
valid power supplied.
Red The indicator is unused for the model
Off No power supplied.
*SWITCH LED (the upper indicator on each RJ45)
LED STATUS Description
P1~P4 and UPLINK
Link/Act
Green
A network device is detected (1000Mbps),
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 1000Mbps.
Yellow A network device is detected (10Mbps or
100Mbps), but no communication activity
is detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off No device is detected.
*PoE LED (the lower indicator on each RJ45)
P1~P4
PoE
Yellow
A valid Powered Device (PD) is detected
and delivering power on this port.
Off
No PD is detected on this port.
UPLINK
PoE
Yellow
Power via another PoE
Powered on all 4 data pairs.
User’s Manual
DIN-SW5G44x4 series
MSTRONIC CO., LTD.
4
Yellow
Blanking
Powered on 2 data pairs. (1,2,3,6 or 4,5,7,8
are all acceptable).
Off No power is detected on this port.
*Power wiring
The PoE switch family allows it to be powered by another PoE source on port UPLINK as a PoE
repeater or extender. For DIN-SW5G44x4 is 44~57VDC.
For PoE operation, make sure your power supply can offer at least 75W for 4x 802.3af PoE port, or
150W for 4x 802.3at PoE port.
If powered via the top terminal, please make sure the input current is not over 10A. total output 8A
maximum. If powered on port UPLINK, the input current is not over 2Amp. Total output 2A
maximum.
Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:
Mode A:
* Data pair A plus V+ on line 1 and 2
* Data pair B plus V- on line 3 and 6
* Data pair C on line 4 and 5
* Data pair D on line 7 and 8
Mode B:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
Mode D (dual,=A+B):
* Data pair A plus V+ on line 1 and 2
* Data pair B plus V- on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
Loading...