MS Sedco Commander, PTM, Privacy Timing Module Installation Instructions Manual
The
Commander
Series
PTM
Privacy Timing Module INSTALLATION INSTRUCTIONS
™
Section 1
General Description
The PTM is a timing module that allows users to control
an automatic door operator for a room where privacy is a
concern, such as a washroom, restroom, clean room, or
photo development room. From the outside of the room,
users are able to activate the door. Once inside, users
are able to lock the door which prevents access from the
outside “push to open” button. When egress is desired,
the user presses an inside “push to open” button which
deactivates the lock and activates the door. A keyswitch
override is present on the exterior, as well as LEDs to
indicate if the room is occupied. Green indicates
available while red indicates occupied.
The delay time between deactivating the lock and
activating the door, as well as the “on time” for door
activation are fully programmable.
WARNING: Devices to be controlled by the PTM
must be low voltage (12-24V) but can be
!
inductive loads. Surge suppressors are standard
on the PTM.
OPTIONS:
PTM = Privacy Timing Module
PTM-HDWE = Prewired Harness to Terminal Block &
Magnetic Door Position Switch
PTM-KIT = Turnkey Kit Includes PTM, PTM-HDWE &
Switches (830B-59J-PTM, 59V-PTM)
WET/DRY CONTACT OPTION:
The PTM has the option to supply power to Relay Output
1 contacts. This is known as having a "Wet" contact
instead of the conventional "Dry" contact closure. To use
output 1 as a "Wet" contact, change the jumper setting
(see Figure 1). The voltage supplied to Output 1 will be
the same as the voltage supplied to the input power wires
of the PTM.
WARNING: Changing jumper settings to enable
the “Wet” Contact option will apply a voltage to
!
the Output 1 relay contact. Please ensure that
any device connected to this output is capable of
accepting voltage. Failure to do so may result in
damage to the device.
WARNING: If the “Wet” Contact Option is to be
used, please ensure that no more than a
!
maximum of 3A current is to be supplied by the
PTM. Failure to do so may result in damage to
the PTM.
Section 2
Basic Installation
1. Mount the PTM in desired location.
2. With power off, make all necessary wiring
connections to the wiring harnesses (Fig. 1) or
Pre-wired Terminal Block (Fig. 2).
Figure 1: PTM Layout and Wiring Connections
NOTICE: These instructions are provided for your
convenience. Please verify your installation is in
!
compliance with all applicable standards upon
completing installation of this device.
Section 3
Technical Data
Model.................................... PTM
Input Power........................... 12-24V AC or DC
Power Consumption............. 2W Maximum
Output Contacts................... Form C, Rated at 3 Amps
Relay Contact Rating............ 3A:120V AC; 3A:60V DC
Temperature Rating............. -22°F to 158°F
(-30°C to 70°C)
Weight................................... <0.25 lbs.
Physical Size......................... 4.75"L x 2.125"W x 0.75"H
Section 4
Warranty
MS SEDCO guarantees this product to be free from manufacturing
defects for 1 year from date of installation. Unless MS SEDCO is
notified of the date of installation, the warranty will be in effect for
1 year from the date of shipment from our factory. If, during the
first year, this device fails to operate and has not been tampered
with or abused, the unit can be returned prepaid to factory and it
will be repaired free of charge. After 1 year, the unit will be
repaired for a nominal service charge. This limited warranty is in
lieu of all other warranties expressed or implied, including any
implied warranty of merchantability, and no representative or
person is authorized to assume for MS SEDCO any other liability
in connection with the sale of our products. All warranties are
limited to the duration of this written warranty. In no event
shall MS SEDCO be liable for any special, incidental,
consequential or other damages arising from any claimed
breach of warranty as to its products or services.
Questions? Call us toll-free at 1-317-842-2545 or
visit us online at www.mssedco.com.
Telephone: (317) 842-2545 www.mssedco.com custsvc@mssedco.com
7898 Zionsville Road Indianapolis, Indiana 46268
Page 1
(82A044) PTMv1017
The
Commander
Series
PTM
Privacy Timing Module INSTALLATION INSTRUCTIONS
™
FIGURE 1—PTM Layout & Wiring Connections
Input Actions
Input 1—Deactivates Output 1, then activates Output 2.
Input 2—Deactivates Output 1.
Input 3—Activates Output 1. Locks out Input 4.
Input 4—Activates Output 2.
Wht/Gray
Wht/Brown
CO M
INPUT 4
Wht/Vio
INPUT 3
Wht/Grn
INPUT 2
PTM
PROGRAM
MODE BUTTON
DISPLAY
ADJUSTMENT
Wht/Red
CO M
Green
Green
Blue
Wht/Blue
Wht/Red
Wht/Grn
Wht/Vio
Wht/Gra
Wht/Brown
Blue
Wht/Blue
INPUT 1
INPUT 1
Input Connections
Input Power 12-24V
(AC or DC)
Switch Input #1 -
Inside Push to Open Switch
Switch Input #2 -
Outside Key Switch and Latchbolt
or Inside Lever Monitor (if used)
Switch Input # 3 -
Inside Push to Lock Switch
Switch Input #4 -
Outside Push to Open Switch
Green
Green
LED DISPLAY KEY
d1 = delay output 1 to 2
d2 = output 2 on time
i1 = input 1 (n.o. / n.c.)
i2 = input 2 (n.o. / n.c.)
i3 = input 3 (n.o. / n.c.)
i4 = input 4 (n.o. / n.c.)
o1 = output 1 (n.o. / n.c.)
o2 = output 2 (n.o. / n.c.)
12-24V AC/DC
Output
Connections
White
Gray
Violet
Y
Brown
Orange
ellow
N.O.
COM
N.C.
N.O.
COM
N.C.
Output
#1
Output
#2
LED Connections
In series with electric lock
N.O.
COM
N.C.
N.O.
COM
N.C.
Telephone: (317) 842-2545 www.mssedco.com custsvc@mssedco.com
N. O.
Ye llow
Output #1
N. C.
Violet
Gray
Output #2
CO M
N. C.
Output #1
RED LED &
Electric Lock
Output #1
GREEN LED
7898 Zionsville Road Indianapolis, Indiana 46268
Orange
Brown
01= wet
CO M
N. O.
01= dry
Wet/Dry
Contact Option
White
(Factory Setting = Dry Contact)
Page 2
(82A044) PTMv1017
Loading...