mspa B-120 Oasis, B-100 Nest, B-140 Elegance, B-121 Castello, B-130 Camaro Owner's Manual And Warranty

CE 001

B-091 Alpine
B-100 Nest
B-110 /B-112 Silver Cloud
B-120 Oasis
B-121 /B-141 Castello/Super Castello

*

*
**
*

**

DO NOT RETURN MERCHANDISE DIRECTLY TO YOUR ORIGINAL SELLING STORE.

CALL MSPA AFTER SALES SERVICE CENTER FOR ANY PRODUCT QUESTIONS.

CONTACT US AT [e-mail]

B-130 /B-150 Camaro/Super Camaro
B-131 /B-151 Luxury Exotic
B-140 Elegance
B-132 /B-152 Birkin

*

*

*

*
*
**

IMPORTANT SAFETY INSTRUCTIONS

! WARNING

For your own safety and that of your equipment, make sure to take the following precautions. Failure to follow warning
notices and instruction may result in property damage, serious injury or death. Improper installation or operation will
void the warranty

When installation and using this equipment, basic safety precautions should always be followed, including the following:

Risk of Electric Shock

WARNING: If the power cord is damaged, purchase a replacement immediately from the manufacturer, MSpa after sale
service center or contact a licensed electrician to replace the cord.

WARNING: DO NOT use an extension cord to connect spa tub to the power plug; provide a properly located receptacle.
DANGER: DO NOT permit any electrical appliances, such as a light, telephone, radio, television, etc, within 1.5m (5

feet) of the spa tub. No appliances are allowed to locate above the spa tub.
WARNING: Electrical parts (except the one with extra-low voltage below 12V) must be inaccessible to occupants in the
spa tub.
WARNING: Electrical parts incorporating any electrical components (except remote control devices) must be properly
located so they will not fall into the spa tub.

WARNING: It is important only to use a 16A (13A for UK，10A for Australia& New Zealand) power supply.
Attention: Static shocks, and how to avoid them

You'll often find shocks are worst in the winter when the air outside is cold and dry. They may disappear in warmer
damper weather. Man-made floor and shoe sole materials have been main factors in most cases of shocks. Static
shocks can be a nuisance - but are not generally a health risk.
Tip - if the air in your room is very dry you could try keeping an open wide dish of water handy - this will evaporate and
moisten the air nearby.

Tip - cotton clothes are comfortable and usually give no static problems.
Tip - try different shoes to see if some give less problems. Leather soles are often good.

To avoid static shocks in MSpa, wet body and hands or touch metal stuff to dissipate charge before entering
into MSpa.

WARNING: The appliance should be supplied through a residual current device (RCD) with a rated tripping current not

exceeding 30 mA. RCD must be tested before each use.

WARNING: RCD must be tested before each use.
WARNING: Make sure the residential electrical connection box is located safely (at least 2m) away from the spa pool.

WARNING: Make sure the floor is capable of supporting the expected load, which you can find from the specification

sheet on page 4, water capacity plus weight.

WARNING: An adequate drainage system must be provided to deal with overflow water.
WARNING: DO NOT leave the spa tub empty for an extended period; this could damage the spa tub.
WARNING: Disconnection must be incorporated in the fixed wiring in accordance with national or local wiring rules. The

disconnection must be intended to ensure a all-pole disconnection.

WARNING: Spray head must not be used in the spa tub.
WARNING: DO NOT connect the spa tub hose to any taps or fittings other than those specified in the user manual.
WARNING: Electric installations should fulfill the local requirements or standards.
WARNING: DO NOT use the spa tub when it rains, thunders or lightens.
WARNING: This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.

WARNING: Children should be supervised to ensure that they do not play with the appliance.
WARNING: To reduce the risk of injury, DO NOT permit children to use this product unless they are closely supervised

all the times.
DANGER: Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children.

2

To avoid accidents, ensure that children cannot use this hot spa tub unless they are supervised at all times.

DANGER: Risk of Accidental Drowning. Always have the spa locked with its top cover after each use.
WARNING: DO NOT bury cord. Locate cord to minimize improper use of lawn mowers, hedge trimmers or other

equipments.
WARNING: DO NOT over pressing down or uplifting the control panel device. Do not put any heavy on control panel
device after installation.

WARNING: Pets must be kept away from the spa tub to avoid any potential damage.
WARNING: Open the spa top cover when the bubble function is operating.
WARNING: DO NOT turn on the spa tub when the water is frozen.
WARNING: Use only approved spa tub accessories. Use of improper or non-approved accessory will void the

manufacturer’s warranty.

WARNING: RISK OF ELECTRIC SHOCK - Install at least 1.5m (5 feet) from all metal surfaces.
WARNING: RISK OF ELECTRIC SHOCK - Never operate any electrical appliances when the spa tub is in use or when

your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within

1.5m(5 feet) of spa tub.

WARNING: During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.
WARNING: Do not expose the spa tub under sunshine directly.
WARNING: Absolutely NO diving or walking on the spa top cover.

WARNING: TO REDUCE THE RISK OF INJURY:

A. The water in the spa tub should never exceed 42°C (108°F). Water temperature between 38°C (100 °F) and 42°C
(108 °F) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and
when spa tub use exceeds 10 minutes.
B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of preg
nancy, pregnant or possibly pregnant women should limit hot spa tub water temperatures to 38°C (100°F). If preg
nant, please consult your physician before using the hot spa tub.
C. Before entering the spa tub, the user should measure the water temperature with an accurate thermometer since the
tolerance of water temperature regulating devices may vary as much as +/- 2°C (5°F).
D. The use of alcohol, drugs, or medication before or during hot spa tub use may lead to unconsciousness with the
possibility of drowning.
E. Individual suffering from obesity or a medical history of heart disease, low or high blood pressure, circulatory system
problems, or diabetes should consult a physician before using a hot spa tub.
F. Individual using medication should consult a physician before using the hot spa tub since some medication may in
duce drowsiness, while other medication may affect heart rate, blood pressure, and circulation.

WARNING: TO REDUCE THE RISK OF INJURY- DO NOT fill water with temperatures exceed 40 °C (104 °F) into the
spa tub directly.
WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot spa tubs.
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above
the normal body temperature of 37°C(98.6 °F). The symptoms of hyperthermia include an increase in the
internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include failure to perceive heat; failure to recognize the need to exit spa; unawareness of impending
hazard; fetal damage in pregnant women; physical inability to exit the spa; and unconsciousness resulting
in the danger of drowning.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS
CAUTION: The spa should not be setup or left out in temperature lower than 4°C if the heater is not operating.
CAUTION: Never use the spa tub when you are alone.
CAUTION: People with infectious diseases should not use the spa tub.
CAUTION: Do not use the spa tub immediately following strenuous exercises.
CAUTION: Always enter and exit the spa slowly and cautiously. Caution of wet floor.
CAUTION:

To avoid damage to the pump, never turn on the spa tub unless the it is filled with water.

WARNING: Precautions to avoid damage due to water freezing.

3

CAUTION: Leave the spa tub immediately once feel uncomfortable or sleepy.
CAUTION: Never add water to chemical. You can add chemicals to the water to avoid strong fumes or violent

reactions that may result in hazardous chemical spray.

CAUTION: Place the spa tub only on a properly prepared site that can withstand the floor loading requirement of the

tub.

NOTE: Please examine equipments before use. See the after sales service centers listed on the last page if you
have any questions of damaged products or missing parts. Verify that the equipment components represent

the models that you intended to purchase.

No part of the appliance shall be located above the bath during use.
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12 V, must be
inaccessible to a person in the bath.
Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot
fall into the bath.
The appliance should be supplied through a residual current device (RCD) with a rated tripping current not exceeding
30 mA.

SPECIFICATIONS

Bubble Spa (EU,UK,SW&AU)

Model No.
(Name)

Pool Shape

Seating
Capacity

Water
Capacity

(Approx.)

Weight

(Approx.)

Outside
Dimensions

Inside
Dimensions

Height

Massage
Air Blower

Filter Pump

Cord
Mounted

Top Lid

B-091
Alpine

Square Oval Round Round Round Round Round

930Ltr/245gal

30kg/66lbs

1.85m/73”

1.45m/57”

0.68m/27”

720W/1HP

12V/60W 12V/60W 12V/60W 12V/60W 12V/60W 12V/60W 12V/60W

EU&UK:

RCD plug

AU: plug

Polyester
laminated

PVC with foil

B-100

* * * * *

Nest

23kg/51lbs 25kg/55lbs 31kg/68lbs 30kg/66lbs

1.86m x 1.25m/
73” x 49”

1.46m x 0.85m/
57” x 33”

0.68m/27” 0.70m/28” 0.70m/28” 0.70m/28” 0.70m/28” 0.70m/28”

720W/1HP 720W/1HP 720W/1HP 720W/1HP 720W/1HP 720W/1HP

EU&UK:

RCD plug

AU: plug

Polyester

laminated PVC

with foil

B-110
Silver Cloud
B-120

*

Oasis

EU&UK:

RCD plug

AU: plug

Polyester

laminated PVC

with foil

B-112
Silver Cloud

EU&UK:

RCD plug

AU: plug

Polyester

laminated PVC

with foil

B-140
Elegance

EU&UK:

RCD plug

AU: plug

Synthetic

leather with foil

B-121 Castello
B-130 Camaro

*

B-131 Luxury Exotic

*

B-132 Birkin

*

30kg/66lbs
33kg/73lbs(B-131 B-132)

(B-121 B-130)

”17/m08.1”17/m08.1”17/m08.1 ”08/m40.2”08/m40.2

”55/m04.1”55/m04.1”55/m04.1 ”36/m06.1”36/m06.1

EU&UK:

RCD plug

AU: plug

Synthetic

leather with foil

B-141 Super Castello

**

B-150 Super Camaro

*

B-151 Luxury Exotic

*

B-152 Birkin

*

6446422 + 4

38kg/84lbs(B-141 B-150)
41kg/90lbs(B-151 B-152)

EU&UK:

RCD plug

AU: plug

Synthetic

leather with foil

lag542/rtL039lag542/rtL039550Ltr/145gal 700Ltr/184gal 700Ltr/184gal 700Ltr/184gal

Pool Cover

Pool
Material

None None None None

Polyester
laminated

PVC

Polyester
laminated

PVC

Polyester
laminated

PVC

Polyester
laminated

PVC

Synthetic leather

PVC leather PVC leather PVC leather

Synthetic leather Synthetic leather

Note: The symbol * after model number (e.g. B-110*) is for purpose of lab test updating, do not have any virtual
meaning. The model number without symbol * on packaging is corresponding to the same product as listed in the
owner’s manual in spite of the symbol *.

4

INSTRUCTIONS

NOTE: Ensure to check all parts are present.

A: Spa top zipper cover with aluminum foil inside
B-091 comes with a top lid, which is

connected to ground cloth by buckle
instead of zipper and digital lock.

B: Control panel
C: Spa pool
D: Temp barrier mat
E: Digital lock (except B-091)
F: Inflation hose
G: Filter cartridge
H: Drainage hose adapter
I: Repair kit
J: Manometer
K: Inflatable bladder
L: Wrench
NOTE: Drawings for illustration purpose only in this manual. Actual product may vary. Not to scale.

A. Site Requirements

WARNING: The floor has to be capable of supporting the expected load of the spa tub.
WARNING: An adequate drainage system has to be provided to deal with overflow water.
IMPORTANT: It is extremely important to make sure the spa tub is placed on a structurallysound surface which will

support the weight of the spa, water, and occupants. Flat, smooth and supporting surface is required.
Uneven or unsound surfaces can damage the tub and void your warranty. Regardless, it is your
responsibility to make sure the site is properly prepared, whether on the ground, on a floor, deck,
patio or slab. Level the surface before filling spa with water.

1pc

1set
1pc
1pc
1pc
1pc
2pcs
1pc
1set
1pc
1pc
1pc

A. B. C. D.

E. F. G. H.

I. J. K. L.

a) Indoor Installation:
Indoor installations have special considerations, be aware of following requirements.

• Verify the supporting floor structure will accommodate the filled weight of the spa with occupants. A qualified
contractor or a structural engineer can help to determine the requirements. The floor where the spa tub is installed
must be a nonslip and flat surface.

• A proper drain is essential to indoor installation. Select flooring which provides a good grip for wet feet.

• Humidity is a naturally side effect of indoor spa installation. Determine the effects of airborne moisture on exposed
wood, paper and etc in the proposed location. The room should be properly ventilated to allow moisture to escape.
Installation of a bathroom fan or other venting system is a good idea to prevent excess condensation in the room.

Note: Do not install the spa tub on a carpet or any other materials that could be damaged by moisture.

b) Outdoor Installation:
WARNING: TO AVOID THE ELECTRIC SHOCK, DO NOT USE THE SPA IN THE RAINS.

It is important to install the spa tub on a firm level surface. If the spa tub is installed outdoors, make sure there are no
sharp objects that could damage the unit. The surface must be flat so the spa tub will be placed firmly and properly.

• If outdoors, make sure that the site has adequate drainage so water splashed out during filling, emptying or using
the spa will not be able to pool around the spa.

• Do not leave the spa tub exposed to direct sunshine for an extended period.

Note:

1. It is important only to use a 16A (13A for UK, 10A for Australia& New Zealand) power supply.

2. If have to use an extension cord/connecting cable, please make sure it is for 16A (13A for UK) purpose and
for outdoor use.

3. For safety reasons, set up spa tub at least a few meters away from power supply and within line of slight
of the spa for safety

5

B-1. RCD Test

WARNING: RISK OF ELECTRIC SHOCK. The RCD plug must be tested before each use.
WARNING: Insert the RCD plug into a residual current device (RCD) protected power receptacle only.
WARNING: Before inserting the plug into a power receptacle, make sure the current rate of the power receptacle

and the fixed wiring are suitable for the Spa. Contact a qualified electrician if you cannot verify.

1. Insert the plug into the power receptacle. (1)

2. Press the “RESET” button. The indicator area should turn red. (2)

3. Then press the “TEST” button. The indicator area should disappear. (3)
WARNING: Do not use if above test fails.

4. Finally, press the “RESET” button again. The indicator area should turn red. The spa is ready for use. (4)

B-2. PRCD Test

Mspa comes with a PRCD plug for Switzerland and Australia standard, please watch below diagram flow for

plug test and use.

RESET

TEST

Press the “RESET” button. The indicator
area should turn red.

RESET

TEST

Then press the “TEST” button. The
indicator area should disappear.

WARNING: Do not use if above test fails.

RESET

TEST

Finally, press the “RESET” button again.
The indicator area should turn red.
The spa is ready for use.

C. Assembly

a) Unfold the Spa pool from the packaging. Take out the spa pool body, cover and temp barrier mat. Make sure spa
and cover top are right side up. Put temp barrier mat under the spa tub.

Note: B-100 includes a side bar, which needs to be placed before filling water to the tub. The side bar helps

*

keeping the spa pool in its proper shape after filling.
For B-091 , please spread out the square ground cloth first, the straps attached on ground cloth is for

*

connection with top lid. Then set up spa pool on it.

Heat preservation mat can prevent heat loss from bottom of the unit and provide better heat preservation
with together of the inflatable bladder being used.

It is possible to install and leave the spa tub outside at a temperature below 4°C, but only if the water temperature

inside the pool is higher than 4°C and water in pipe is not frozen. The spa tub can be operated in cold weather with
temperature down to maximum -10°C if the unit is properly set up and no frozen water inside the control box, pipes
or spa pool. It’s helpful to put temp barrier mat in between the spa pool and the ground. Similar mat which is made of

foam material or other materials with temp barrier function can also be used.

Don’t install Mspa onto the lawn as grass may cause air pump damped and rusted which could result the air pump

works improperly and will void your warranty.

6