Page 1
USER MANUAL
LED MOVING HEAD LIGHT
Model: MHLED 36F
(12*15W RGBWA 5IN1 DMX 512 14CH)
Please read over this manual before operation the light
Page 2
1
CONTENTS
Contents…………………………………………………………..……
1
Important notice ………………………………………………………
2
Attention ……………………………………………………………….
2
I. Product Illustration…………………………………………………..
2
II .The installment of led moving head …………………..………
2
III. The connection of control correspond wire ………………..……
3
IV. Clean maintenance …………………………………………….…
3
V. Warning ……………………………………………………..………
3
VI. Difficult processing …………………………………………..……
4
VII. Equipment and appendix…………………………………………
4
VIII. Technical parameters……………………………………………
4
IX. Panel operation ……………………………………………………
5
1. DMX 512…………………………………………………….
5
2. DN.Pr. (DMX512) …………………………………………..
6
3. TEST ………………………………………………………...
6
4. Audi ………………………………………………………….
7
5. R.Pan ………………………………………………………..
7
6. R.TILT………………………………………………………..
7
7. RESET ………………………………………………………
8
8. Channel list …………………………………………………
8
Page 3
2
Important notice:
· In this instruction for use contains about the installment and the use aspect important
information of the LED moving head. When installing and using, you need to look this usage
instruction strictly.
· Before open the LED moving head and if you want to do the repair work, please make
sure the power source is at the separation condition.
Attention:
Unceasingly carries on the product improvement about our company the policy, in this
instruction booklet carries the data will have the possibility to be able to change in the future,
when no longer separate notice change matters concerned. Our company retains when the
product improvement changes the related specification the authority. This instruction booklet
publisher cannot be responsible regarding this instruction booklet in information accuracy,
also cannot the related consequence which causes regarding these information be
responsible.
I. Product Illustration
Our product adopt semiconductor to produce radiation, LED as light origin. With
advantage of operation quietly, less power waste, high brightness, gaily-colored, astigmatic,
high longevity (60-100 thousands hours), non-calorific etc. Our product apply to use 3 kinds
light as red, green, blue LED, synthesize turn colors under election, can create effect of auto
gradual change/skip change color, frequent blinking. Can accept control by DMX512, real
save power, no pollution green lighting tool.
II .The installment of led moving head
Use the four bolts with M8 size by the clip of the LED moving head to install it. Should
guarantee the reliability of the install, this way is to prevent the LED moving head occur
swings and skids when it’s working. The weight is about 8Kg of each LED moving head,
before install, you should confirm the structure whether can support this weight of the LED
moving head light. In order to guarantee the security, you also need to install a safety chain
in the lamp body side handle.
Page 4
3
Warning: Do not use the hand of the LED moving head to up and down or fix.
III. The connection of control correspond wire
The connection of controller between the led moving head lamp and respectively led
moving head lamp should use the twin core shielded cable, and the diameter of each core at
least be 0.3mm. After receives the DMX512 signal, the lamp of nearby the address switch
condition will glisten. When it’s do not receive the DMX signal, the lamp will in extinguish
condition, but if the signal lamp glisten continuously, the mean is the DMX signal is not be
correct.
When installing, uses the DMX signal terminal is much better. It can avoid the digital
control signal breached by the electrical noise. Generally speaking, the DMX terminal is
Cannon plug coupling, it has a 120 ohm resistances between the 2 feet and 3 feet, it will
connected on the last led moving head lamp’s digital plug of the led moving head lamp
chain.
IV. Clean maintenance
In order to guarantee the LED moving head lamp can work better, you should keep the
lamp in clean state. Suggests clean the lamp body and fan in each 15 days. For the PVS
board, you need clean it on time. When you cleaning the PVC piece, please do not use any
soluble cleanser,
V. Warning
·Don’t disassemble and assemble the LED moving head.
·Please do not put the led moving head lamp in water or other any type’s liquids and the
metal (IP20).
·Do not install the led moving head lamp in the humidity environment.
·Should maintain the minimum 0.5 meter distance between the led moving head lamp and
other neighboring object surface.
Page 5
4
VI. Difficult processing
Question
Answer
The LED moving head lamp can not
start.
Inspects the fuse on the rear panel.
Although shines, but the LED moving
head lamp can not accept the
instruction of the controller.
Check the digital start address (sees
09th) and also check the connection
situation of the communication control
line the (to see 03rd).
LED moving head lamp only can work
intermittently.
Inspect the power supply and voltage
is whether normal.
Do not receive the DMX512 signal
Whether the signal lines do contact
good or broken
The light beam appears gloomily.
Inspect the optics part is whether
clean.
Other maintains work should by the specialist which has the experience
to carry on.
VII. Equipment and appendix
1 led moving head lamp 1PCE
2 the product of USER MANUAL 1PCE
3 Power source connected lines 1PCE
4 signal lines 1PCE
VIII. Technical parameters
Voltage / frequency: □90-130V/
□
,√180V-240V/50-60Hz
Bulbs: 12*15W RGBWA 5IN1
Power: 180W
Control signal: DMX 512, in sets at the automatic procedure
Channel: 14 CH, DMX512 channel control
Motion: level 540°, vertical 280°, horizontal and vertical uses the electronic replacement
function
Color: 16.7 million kinds of colors changes
Adjusts the light: 0-100 electron adjusts the light, various colors may alone move also may
Page 6
5
mix the color tone
Strobe: 1-25/second high speed strobe, but single color mixes the color strobe
IX. Panel operation
This control display panel menu especially for the many kinds of models computer
lamp design, provided the many kinds of functions control mode, the control has been
simple. Act regarding certain model computer lamps, the corresponding menu option
hypothesis is invalid.
1. DMX 512(address establishment).
This function can change the address value.
1.1. Presses down “ESC” key once or many times, until demonstrates "A.001".This time will
press "UP" or "DOWN" the key glances over other function tables.
1.2. Press the key of “ENTER” the letter “A” extinguishes, then use “UP” or “DOWN” the key
choose the address value“001-512”,according to “ENTER” the key confirmed the withdrawal
or presses “ESC” the key to give up the withdrawal.
1.3. Must accept when main engine synchronization (namely stochastic pattern) must
establish the address value as "001".
1.4. Under explicit address value condition, if will install the connectionless DMX controller
display monitor to glitter, if will install connects the DMX controller display monitor not to
glitter, but the DMX signal indicating lamp because of will have the signal to glitter.
2. DN.Pr.(DMX512)
This function allows you to choose the different operating mode.
2.1 According to “UP” or “DOWN” glances over other function tables.
2.2 Enters according to “ENTER”, again presses “UP” or “DOWN” to choose “nod.1” or
“nod.2”,according to “ENTER” the key confirmed the preserved withdraw or presses “ESC”
not to preserve the withdrawal.
Page 7
6
Nod.1: Normal channel digital control.
Nod.2: Less channels digital control.
2.3 Must accept when the host synchronization (namely subsidiary pattern) must establish in
advance DMX as “nod.1”.
3. TEST
Outside this function allows you not to need to connect under the controller condition
to carry out the internal demonstration formula .This establishment is also preserved, does
not withdraw from the test procedure when you each time start all automatically enters the
test formula.
Presses the key of “UP” or “DOWN” will browse other function tables; will enter
according to “ENTER”.
3.1. Nod.1:
According to “UP” or “DOWN” the key chooses other patterns, enters according to
“ENTER”, and demonstrates "RUN" the test movement, If you need to withdraw, according
to "ESC" withdrawal.
3.2. nast (control by the host)
This function allows you run when the test to need taking responsibility machine to
send out the DMX synchronized signal to the auxiliary engine use.
Press
the "UP" or “DOWN” key to choose other patterns, enters according to "ENTER",
demonstrated "ON" sends out the signal as the main engine, the DMX indicating lamp is
bright, demonstrated "OFF" does not send out the signal, the DMX signal indicating lamp
extinguishes, according to "ENTER" the confirmation guarantee withdrawal, does not
preserve the withdrawal according to "ESC". Establishes after "ON", you must sever exterior
DMX controller connection, cannot have two above same establishments the host on the
identical company road.
Page 8
7
4. Audi(Voice control stimulation)
This function allows you to use the sound to stimulate the test formula.
According to "UP" Or "DOWN" the key will glance over other function tables.
Enters according to "ENTER", again presses "UP" either "DOWN" the choice "ON" or
"OFF" when the expression test movement whether uses the sound to stimulate. "ON" the
expression use voice control, "OFF" the expression does not use the voice control, by test
pattern under automatic control. After has established "ON", when movement test formula
the audio signal indicating lamp will glitter along with the music.
5. R.Pan.( Level pan reversal)
This function allows you to reverse the horizontal movement.
Enters according to "ENTER", use "UP" or "DOWN" key, if needs to reverse, choice
"ON", if you do not need to reverse, the choice "OFF", the confirmation preservation
withdrawal or presses "ESC" according to "ENTER" not to preserve the withdrawal.
6. R.TILT.( Vertical tilt reversal)
This function allows you to reverse the vertical movement.
Enters according to “ENTER”, use “UP” or “DOWN” key, if you needs to reverse,
choice “ON”, if you do not need to reverse, the choice "OFF", the confirmation preservation
withdrawal or presses "ESC" according to "ENTER" not to preserve the withdrawal.
7. RESET (Install Replacement)
This function lets you go to the again starter to return to the original standard localization.
According to "ENTER" confirmation
8. Channel list
CH
Value
Function
CH1
0--255
X Scanning
CH2
0--255
Y Scanning
CH3
0--1
Close
Page 9
8
2--100
Strobe slow - fast
101--199
Random Strobe slow - fast
208--217
Reset (After 3sec.)
218--255
Open
CH4
0--255
Dimmer Dark to Light
CH 5
0--2
RED
3-4
Red & White
5--7
Red & Green
8--9
Green & Blue
10--12
G
13--14
GW
15--17
GB
18--19
GBW
20--22
B
23--24
BW
25--27
RB
28--29
RBW
30--39
W
40-49
RGBW
50--83
R Open, G Gradual close
84--117
R Gradual, G Open, B close
118--151
G Open, R Close, B Gradual
152--185
R close, G Gradual, B open
186--218
B Open, R Gradual, G close
219--252
R Open, B Gradual, G close
253--255
RGBW DIMMER
Page 10
9
CH6
0--255
R, Dimmer Dark to Light
CH7
0--255
G, Dimmer Dark to Light
CH8
0--255
B, Dimmer Dark to Light
CH9
0-255
W, Dimmer Dark to Light
CH10
0-255
A, Dimmer Dark to Light
CH11
0--5
RGBW, Color is decide by CH5
6--127
RGBW Graduated, Speed adjustment, from slow to fast
128--255
R,RG,G,GB,B,RB,RGB,RGBW RAINBOW Effect, Speed
adjustment, from slow to fast
CH12
0--255
X Fine
CH13
0--255
Y Fine
CH14
0--251
X/Y speed adjustment, Fast - slow
252--255
X,Y Vector
Loading...