
18
17
16
15
14
13
12
11
10
Output B
Output B
Rsense B
Rsense B
V+
V+
Rsense A
Rsense A
Output A
8170 Thompson Road Cicero, N.Y. 13039 (315) 699-9201
M.S.KENNEDY CORP.
ISO 9001 CERTIFIED BY DSCC
75 VOLT 10 AMP MOSFET
H-BRIDGE PWM MOTOR
DRIVER/AMPLIFIER
4224
The MSK 4224 is a complete H-Bridge circuit to be used for DC brushed motor control or Class D switchmode
amplification. All of the drive/control circuitry for the lowside and highside switches are internal to the circuit. The
250KHz PWM circuitry is internal as well, leaving the user to only provide an analog signal for the motor speed/
direction, or audio signal for switchmode audio amplification. The MSK 4224 is constructed on a space efficient
ceramic coated insulated metal substrate that can be directly connected to a heatsink.
DESCRIPTION:
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
1
2
3
4
5
6
7
8
9
HEN
Disable
N/C
Input
Ground
Ground
N/C
Vcc
Output A
Rev.- 06/98
1
FEATURES:
•Low RDS(ON) 0.020Ω Typical
•Low Cost Complete H-Bridge
•10 Amp Capability, 75 Volt Maximum Rating
•Self-contained Smart Lowside/Highside Drive Circuitry
•Internal 250KHz PWM Generation, Shoot-through Protection
•Isolated Case Allows Direct Heatsinking
•Four Quadrant Operation, Torque Control Capability
•Logic Level Disable Input
•Logic Level High Side Enable Input for Special Modulation or Function

OUTPUT CHARACTERISTICS
RDS (ON) 4
VDS(ON) Voltage 1
Instantaneous Forward Voltage 1
Reverse Recovery Time 1
Leakage Current 1
PWM Frequency
Vcc SUPPLY CHARACTERISTICS
Quiescent Bias Current
Vcc Voltage Range 1
INPUT SIGNAL CHARACTERISTICS 1
Analog Input Voltage
Analog Input Voltage
Analog Input Voltage
LOGIC CONTROL INPUTS 1
SWITCHING CHARACTERISTICS 1
Rise-Time
Fall-Time
Dead-Time
V+ High Voltage Supply ..................................... 75V
VCC Logic Supply ................................................ 16V
IOUT Continuous Output Current ............................ 10A
IPK Peak Output Current ..................................... 20A
VOUT Output Voltage Range .... GND -2V min. to V + max.
θJC Thermal Resistance ................................ .5.3°C/W
(Output Switches)
ABSOLUTE MAXIMUM RATINGS
Each MOSFET ID=10A
Each MOSFET ID=10A 3
Each MOSFET IS=10A Intrinsic Diode 3
Intrinsic Diode
Each MOSFET V+=70V
Analog Input=6VDC
Output A,B=50% Duty Cycle
Output A=100% Duty Cycle High
Output B=100% Duty Cycle High
Input Voltage LO
Input Voltage HI
Input Current (DISABLE=0V)
Input Voltage LO
Input Voltage HI
Input Current (HEN=0V)
RL=100Ω
Parameter
ELECTRICAL SPECIFICATIONS
Units
Ω
V
V
nS
uA
KHz
mA
V
V
V
V
V
V
uA
V
V
uA
nS
nS
nS
Max.
0.013
TBD
TBD
280
25
275
TBD
16
-
-
-
0.8
-
-135
0.8
-
-270
-
-
-
MSK 4224
Typ.
-
TBD
TBD
-
1.0
250
43
12
6
4
8
-
-
-
-
-
-
TBD
TBD
100
Min.
-
-
-
-
-
225
-
9
-
-
-
-
2.7
-
-
2.7
-
-
-
-
Test Conditions 2
Rev.- 06/98
2
TST Storage Temperature Range .... -65C to +150°C
TLD Lead Temperature Range .................. .....300°C
(10 Seconds)
TC Case Operating Temperature
MSK4224 ........................ ....-25°C to +125°C
TJ Junction Temperature ................... .....+150°C
NOTES:
1 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
2 Vcc=+12V unless otherwise specified.
3 Measure using a 300µS pulse with a 2% Duty Cycle.
4 On Resistance is specified for the Internal MOSFET for Thermal Calculations. It does not include the package pin resistance.
All Ratings: Tc= +25°C Unless Otherwise Specified
Disable Input
HEN Input