MSI MS-7043, PT8 Neo-V, PT880 Neo-FISR, PT880 Neo-FSR, PT880 Neo-LSR User Manual
...
i
G52-M7043X1
PT880 Neo-V/PT8 Neo-V/PX8 Neo-V
MS-7043 (v1.X) A TX Mainboard
PT880 Neo-V PT8 Neo-V PX8 Neo-V
ii
Manual Rev: 1.0
Release Date: March 2004
FCC-A Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct
the interference at his own expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU
RESEAU.
Micro-Star International
MS-7043
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
iii
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. W e take every care in the preparation of this document,
but no guarantee is given as to the correctness of its contents. Our products
are under continual improvement and we reserve the right to make changes
without notice.
Trademarks
All trademarks are the properties of their respective owners.
Intel® and Pentium® are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Windows® 95/98/2000/NT/XP are registered trademarks of Microsoft
Corporation.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix T echnologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
Revision History
Revision Revision History Date
V1.0 First release for PCB 1.X March 2004
Technical Support
If a problem arises with your system and no solution can be obtained from the
user’s manual, please contact your place of purchase or local distributor.
Alternatively, please try the following help resources for further guidance.
V isit the MSI website for FAQ, technical guide, BIOS updates, driver
updates, and other information: http://www.msi.com.tw/program/ser-
vice/faq/faq/esc_faq_list.php
Contact our technical staff at: support@msi.com.tw
iv
1. Always read the safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Keep this equipment away from humidity.
4. Lay this equipment on a reliable flat surface before setting it up.
5. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS.
6. Make sure the voltage of the power source and adjust properly 110/220V before
connecting the equipment to the power inlet.
7. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
8. Always Unplug the Power Cord before inserting any add-on card or module.
9. All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a service
personnel:
††
††
† The power cord or plug is damaged.
††
††
† Liquid has penetrated into the equipment.
††
††
† The equipment has been exposed to moisture.
††
††
† The equipment has not work well or you can not get it work according to User’s
Manual.
††
††
† The equipment has dropped and damaged.
††
††
† The equipment has obvious sign of breakage.
12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE
TEMPERA TURE ABOVE 600 C (1400F), IT MAY DAMAGE THE EQUIPMENT.
Safety Instructions
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
v
CONTENTS
Copyright Notice ............................................................................................................ iii
Trademarks.................................................................................................................... iii
Technical Support.......................................................................................................... iii
Safety Instructions ........................................................................................................ v
Getting Started ........................................................................................................ 2-1
Mainboard Specifications ...................................................................................2-2
Mainboard Layout ...............................................................................................2-4
Back Pa nel...........................................................................................................2-7
Chapter 2. Hardware Setup .................................................................................. 2-1
Central Processing Unit: CPU.............................................................................. 2-2
CPU Core Speed Derivation Procedure ...................................................... 2-3
Memory Speed/CPU FSB Support Matrix ...................................................2-3
Installing the CPU Fan .................................................................................2-4
Memory ...............................................................................................................2-5
Memory Population Rules............................................................................ 2-5
Power Supply .....................................................................................................2-6
ATX 20-Pin Power Connector: ATX1 .......................................................... 2-6
ATX 12V Power Connector: JPW1.............................................................2-6
Connectors .........................................................................................................2-7
Floppy Disk Drive Connector: FDD1 ............................................................2-7
S-Bracket (SPDIF) Connector: JSP1 (Optional) .......................................... 2-7
Chassis Intrusion Switch Connector: JCI1 (Optional) ................................2-8
CD-In Connector: JCD1 ...............................................................................2-8
Serial ATA RAID 0, 1 Connectors: SATA1, SATA2 (for PT880/PT8 Neo-V) 2-8
Fan Power Connector: CPUFA1 ................................................................ 2-9
D-Bracket™ 2 Connector: JDB1 (Optional) ................................................2-9
Hard Disk Connectors: IDE1 & IDE2 ..........................................................2-10
Front Panel Connectors: JFP1 & JFP2 ...................................................... 2-10
Front USB Connectors: JUSB1 & JUSB2 ................................................. 2-11
Jumpers ............................................................................................................ 2-12
Clear CMOS Jumper: JBAT1 ..................................................................... 2-12
Front Panel Audio Connector: JAUD1.......................................................2-12
Slots ..................................................................................................................2-13
PCI Interrupt Request Routing ...................................................................2-13
AGP (Accelerated Graphics Port) Slot .....................................................2-13
PCI (Peripheral Component Interconnect) Slots ....................................... 2-13
Chapter 3. BIOS Setup ............................................................................................ 3-1
The Main M enu.................................................................................................... 3-2
Frequency/Voltage Control................................................................................. 3-3
1-1
Getting Started
Getting Started
Thank you for choosing the MS-7043 (PT880 Neo-V/PT8 NeoV/PX8 Neo-V) v1.X ATX mainboards. The MS-7043 series are
superior computer mainboards based on VIA® PT880/PT800/P4X533
Northbridge & VT8237 Southbridge for optimal system efficiency.
Designed to fit the advanced Intel® Pentium® 4 processors in 478
pin package, the MS-7043 series deliver a high performance and
professional desktop platform solution.
1-2
MS-7043 ATX Mainboard
Mainboard Specifications
CPU
h Supports Intel® P4 Northwood/Prescott (Socket 478) processors
h FSB 400 (for Northwood only), 533, 800 (for PT880/PT800 only) MHz
h Supports up to 3.4GHz or higher speed (Please refer to the latest online news at
http://www.msi.com.tw/program/products/mainboard/mbd/
pro_mbd_cpu_support.php)
Chipset
h VIA® PT880 chipset (for PT880 Neo-V)
- Supports FSB 800/533/400MHz
- Supports AGP 8X interface
- Supports DDR 400/333/266 memory interface
h VIA® PT800 chipset (for PT8 Neo-V)
- Supports FSB 800/533/400MHz
- Supports AGP 8X interface
- Supports DDR 400/333/266 memory interface
h VIA® P4X533 chipset (for PX8 Neo-V)
- Supports FSB 533/400MHz
- Supports AGP 8X interface
- Supports DDR 333/266 memory interface
h VIA® VT8237 chipset
- High Bandwidth V-link Client controller
- Integrated Faster Ethernet LPC
- Integrated Hardware Sound Blaster/Direct Sound AC97 audio
- Ultra DMA 66/100/133 master mode PCI EIDE controller
- ACPI
- Supports Serial ATA
- Supports USB2.0
PT880 Neo-V Main Memory
h Supports six memory banks using three 184-pin DDR DIMMs
h Supports dual-channel memory
h Supports a maximum memory size up to 3GB
h Supports 2.5v DDR SDRAM DIMM
PT8 Neo-V/PX8 Neo-V Main Memory
h Supports four memory banks using two 184-pin DDR DIMMs
h Supports single-channel memory
h Supports a maximum memory size up to 2GB
h Supports 2.5v DDR SDRAM DIMM
Slots
h One AGP (Accelerated Graphics Port) slot supports 8x/4x (AGP 3.0) at 1.5V (3.
3V not supported)
h Five 32-bit Master PCI bus slots (support 3.3v/5v PCI bus interface)
1-3
Getting Started
Onboard IDE
h An IDE controller integrated in the VIA® VT8237 chipset
- Supports IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA 66/100/133
operation modes
- Can connect up to four Ultra ATA drives
Onboard Serial ATA (for PT880 Neo-V/PT8 Neo-V)
h Serial ATA/150 controller integrated in the VIA® VT8237 chipset
- Up to 150MB/sec transfer rate
- Can connect up to two Serial ATA drives
USB Interface
h 8 USB ports
- Controlled by VT8237 southbridge
- 4 ports in the rear I/O, 4 ports via the external bracket
On-Board Peripherals
h On-Board Peripherals include:
- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes
- 1 serial port (COM A)
- 1 parallel port supports SPP/EPP/ECP mode
- 8 USB 2.0 ports (Rear x 4 / Front x 4)
- 1 RJ45 LAN jack
- 1 D-Bracket2 pinheader (Optional)
- 1 S-Bracket pinheader (Optional)
- 1 Line-In / Line-Out /Mic
- 1 Coaxial SPDIF out (Optional)
Audio
h AC97 link controller integrated in VT8237
h VIA® VT1617 6-channel audio codec
- Compliance with AC97 v2.2 Spec
- Meets PC2001 audio performance requirement
PT880 Neo-V LAN
h VIA® VT8237 integrated MAC
h VIA® VT6122 Gigabit LAN controller
PT8 Neo-V/PX8 Neo-V LAN
h VIA® VT8237 integrated MAC
h VIA® VT6103L 10/100 PHY
BIOS
h The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral
devices and expansion cards of the board automatically
h The mainboard provides a Desktop Management Interface (DMI) function which
records your mainboard specifications
Dimension
h ATX Form Factor: 30.5cm x 19.5cm
Mounting
h 6 standard mounting holes
1-4
MS-7043 ATX Mainboard
Mainboard Layout
PT880 Neo-V (MS-7043 v1.X) ATX Mainboard
- VIA® PT880 Northbridge
- VIA® VT6122 Gigabit LAN
- 2 Serial ATA connectors
- 3 DDR DIMMs up to 3 GB
BATT
+
D
I
M
M
1
D
I
M
M
3
D
I
M
M
2
JAUD1 JSP1
JUSB2
A
T
X
1
CPUFA1
SATA1
SATA2
JFP1
JDB1
JFP2
VIA
Audio Codec
VT1617
Winbond
W83697HF
VIA
Gigabit LAN
VT6122
BIOS
PCI 5
PCI 4
PCI 3
PCI 2
PCI 1
IDE 2
IDE 1
JPW1
Top :
Parallel Port
Bottom:
COM A
Top : Mous e
Bottom: Keyboard
T : LAN Jack
B: USB Po r ts
JCD1
F
D
D
1
AGP1
JBAT1
JUSB1
T: SPD IF Out
B: USB Po r ts
T:
M:
B: Mic
Line-In
Line-Out
VIA
VT8237
VIA
PT880
Loading...