MSI Hetis 915, Hetis 945, 945-E - Hetis - 0 MB RAM, Hetis 900, MS-6439 User Manual

Hetis 900 Series
MS-6439 (V1.X) Barebone
G52-64391X1
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below.
=Reorient or relocate the receiving antenna. =Increase the separation between the equipment and receiver. =Connec the equipment into an outlet on a circuit different from that to which the
receiver is connected.
=Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.
VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
Hetis 900
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
may cause undesired operation.
ii
Trademarks
All trademarks are the properties of their respective owners.
Intel® and Pentium® are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Windows® 95/98/2000/NT/XP are registered trademarks of Microsoft Corporation.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
U.S. Patent Numbers. 4,631,603; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection tech-
nology must be authorized by Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision. Reverse engineer-
ing or disassembly is prohibited.
Revision History
Revision Revision History Date
V1.0 First release January 2007
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
iii
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this Users Manual for future reference.
3. Keep this equipment away from humidity.
4. Lay this equipment on a reliable flat surface before setting it up.
5. The openings on the enclosure are for air convection hence protects the
equipment from overheating. DO NOT COVER THE OPENINGS.
6. Make sure the voltage of the power source and adjust properly 115/230V
before connecting the equipment to the power inlet.
7. Place the power cord such a way that people can not step on it. Do not
place anything over the power cord.
8. Always Unplug the Power Cord before inserting any add-on card or module.
9. All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a
service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the equipment.
- The equipment has been exposed to moisture.
- The equipment has not work well or you can not get it work according to
Users Manual.
- The equipment has dropped and damaged.
- The equipment has obvious sign of breakage.
12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED,
STORAGE TEMPERATURE ABOVE 400 C (1020F), IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
iv
Warning:
1. For every changes in powercords usage, please use an approved power
cord with condition greater or equal to H05VV-F,3G , 0.75mm2.
2. Internal part is hazardous moving parts, please keep fingers and other
body parts away.
3. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
4. Do not disable the protective earth pin from the plug, the equipment must
be connected to an earthed mains socket-outlet.
v
WEEE Statement
vi
vii
viii
CONTENTS
Chapter 1. Getting Started....................................................................................1-1
Mainboard Specifications..............................................................................1-2
System Configuration....................................................................................1-4
Thermal Solution............................................................................................1-7
Chapter 2. Hardware Setup..................................................................................2-1
Mainboard Layout.........................................................................................2-2
CPU (Central Processing Unit)......................................................................2-3
Memory..........................................................................................................2-4
Power Supply................................................................................................2-5
Front Panel....................................................................................................2-6
Back Panel.....................................................................................................2-7
Connectors....................................................................................................2-9
Jumper...........................................................................................................2-12
Slot................................................................................................................2-13
Chapter 3. System Assembly...............................................................................3-1
Overview.....................................................................................................3-2
Installation Tools....................................................................................3-2
Installation Screws...............................................................................3-2
Checking the Items................................................................................3-3
Installation Procedures.................................................................................3-4
Removing Chassis Cover....................................................................3-4
Installing Hard Disk Drive (HDD)...........................................................3-5
Installing Optical Disk Drive (ODD).......................................................3-6
Installing Card Reader (Optional).........................................................3-7
Installing Memory Modules...................................................................3-8
Installing CPU........................................................................................3-9
Installing CPU Cooler............................................................................3-10
Restoring Chassis Cover......................................................................3-11
Installing Footstand...............................................................................3-12
Chapter 4. BIOS Setup.............................................................................................4-1
Entering Setup.............................................................................................4-2
Control Keys........................................................................................4-3
Getting Help..........................................................................................4-3
General Help <F1>...............................................................................4-3
The Main Menu............................................................................................4-4
Standard CMOS Features...........................................................................4-6
Advanced BIOS Features...........................................................................4-8
Advanced Chipset Features.......................................................................4-12
ix
Integrated Peripherals.................................................................................4-15
Power Management Setup.........................................................................4-19
PnP / PCI Configurations.............................................................................4-22
PC Health Status.........................................................................................4-24
Frequency / Voltage Control......................................................................4-25
Load Fail-Safe / Optimized Defaults..........................................................4-27
Set Supervisor / User Password..............................................................4-28
Appendix A. Realtek ALC888 Audio....................................................................A-1
Installing the Realtek HD Audio Driver.................................................................A-2
Installation for Windows 2000/XP...............................................................A-2
Software Configuration.......................................................................................A-4
Sound Effect................................................................................................A-5
Mixer.............................................................................................................A-8
Audio I/O.....................................................................................................A-12
Microphone.................................................................................................A-15
3D Audio Demo..........................................................................................A-17
Information..................................................................................................A-17
Hardware Configuration....................................................................................A-18
Using 2-, 4-, 6- & 8- Channel Audio Function...................................................A-18
x
Chapter 1
Getting Started
Congratulations for purchasing Hetis 900 Series (MS-6439) Barebone. Hetis 900 Series Barebone is your best Slim PC choice. With the fantastic appearance and small form factor, it can easily be set anywhere. The feature packed platform also gives you an exciting PC experience.
MS-6439 Barebone
Mainboard Specifications
Processor Support
- Supports Intel® Conroe LGA775 CoreTM 2 Duo up to E6700
- Supports Intel® Presler LGA775 Pentium® D up to 960 (3.6GHz)
(For the latest information about CPU, please visit http://www.msi. com.tw/program/products/slim_pc/slm/pro_slm_cpu_support.php)
Supported FSB
- 400 / 533 / 800 / 1066 MHz
Chipset
- North Bridge: VIA® P4M900 Chipset
- South Bridge: VIA® VT8237A Chipset
Memory Support
- DDR2 400 / 533 / 667 SDRAM (2GB Max)
- 2 DDR2 DIMMs (240pin / 1.8V)
LAN
- Supports Giga LAN by Realtek® RTL8110SC
- Supports 10/100 LAN by Realtek® RTL8100C (Optional)
Audio
- Chip integrated by Realtek® ALC888
- Flexible 8-channel audio
IDE
- 1 IDE port by VIA® VT8237A
- Supports Ultra DMA 66/100/133 mode
- Supports PIO, Bus Master operation mode
SATA
- 2 SATA ports by VIA® VT8237A
- Supports two SATA devices
- Supports storage and data transfers at up to 150 MB/s
1-2
Connectors Back Panel
- 1 PS/2 Mouse Port
- 1 PS/2 Keyboard Port
- 2 COM Ports
- 1 VGA Port
- 1 DVI Port
- 6 Audio Jacks
- 1 LAN Jack (RJ45)
- 4 USB 2.0 Ports
Front Panel
- 2 Audio Jacks (Headphone and Microphone)
- 2 USB 2.0 Ports
Getting Started
On-Board Pinheaders
- 1 CD-In Pinheader
- 1 Card Reader Pinheader
- 1 SPDIF-Out Pinheader
(For HDMI Graphics Card Audio Line Use Only)
Slots
- 1 PCI Express Slot (For Riser Card Use Only)
Form Factor
- Proprietary (334MM x 190 MM)
Mounting
- 5 mounting holes
1-3
MS-6439 Barebone
System Configuration
Front View
1. Headphone (Green) 5. HDD LED
2. Microphone (Pink) 6. ODD Eject / Close Button
3. USB 2.0 Ports 7. Optical Disk Drive (Optional)
4. Power Button / Power LED 8. Card Reader Drive (Optional)
1-4
Back View
Getting Started
1. Voltage Selector 8. DVI Port
2. Power Jack 9. VGA Port
3. Ventilation Hole 10. Audio Jacks
4. USB 2.0 Ports 11. Power Switch
5. PS/2 Mouse (Green) 12. Support Bracket Spring
6. PS/2 Keyboard (Purple) 13. LAN Jack (RJ45)
7. Serial Ports 14. Expansion Slots
1-5
MS-6439 Barebone
Chassis Design
Dimension: 330MM (D) x 320MM (W) x 94MM (H) Minimized screw structure Detachable bay housing Multiple ventilation holes
Back
Side
Bottom
1. CPU Fan Ventilation Hole 5. System Ventilation Hole
2. System Ventilation Hole 6. System Ventilation Hole
3. System Fan Ventilation Hole 7. System Ventilation Hole
4. Power Supply Ventilation Hole
1-6
Getting Started
Thermal Solution
To prevent the system from overheating, we have adopted a specially designed CPU
cooler and multiple ventilation holes for better cooling effects. The specially designed
CPU cooler supports Intel® LGA775 - Conroe CoreTM 2 Duo and Presler Pentium® D.
The following figures illustrate how the system fan effectively exhausts hot air
through multiple ventilation holes.
CPU Cooler Air Flow Direction
Air In
Air Out Air Out
Air Out
Air Out
1-7
MS-6439 Barebone
System Design
System Fan
Back Panel Power Supply
Power
Supply Fan
CPU Socket
Memory
DIMM Slots
Front Panel
Driver Bays
(from top to bottom)
Card Reader Drive
Optical Disk Drive
Hard Disk Drive
1-8
System Air Flow Direction
System Fan
Getting Started
Back Panel Power Supply
Power
Supply Fan
CPU Socket
Memory
DIMM Slots
Front Panel
After the installation is completed, please keep other
objects away from the ventilation hole at least 2.5cm
and above. Do not block the ventilation hole.
Driver Bays
(from top to bottom)
Card Reader Drive
Optical Disk Drive
Hard Disk Drive
1-9
Chapter 2
Hardware Setup
This chapter provides you with the information about hard­ware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. Use a grounded wrist strap before handling computer components. Static electricity may damage the components.
ONLY FOR SERVICE PERSONEL
Always unplug the power cord before in­serting any add-on card or module.
MS-6439 Barebone
BATT
LAN Chip
CASE_OPEN1
Mainboard Layout
T:
M:
B:
T:RS-Out
M:CS-Out
B:SS-Out
Line-In
Mic
Line-Out
J1
Top: LAN Jack
Top : Mouse
Bottom:
Top : VGA Port
Bottom: DVI Port
COM Ports
Keyboard
Bottom: USB Ports
USB Ports
Codec
JCD1
SYS_F2
BIOS
IDE1
VIA
P4M900
SATA2 SATA1
VIA
VT 8237A
ATX1
SLOT1
CR1
DIMM2
CPU_F1
JACK3JACK2USB2
2-2
DIMM1
USB1
MS-7331 (V1.X) Mainboard
JPW1
+
JBAT1
JFP1
Hardware Setup
CPU (Central Processing Unit)
The mainboard supports Intel® Conroe CoreTM 2 Duo and Presler Pentium® D. The mainboard uses a CPU socket called LGA775. When you are installing the CPU, make sure to install the cooler to prevent overheating. If you do not have the CPU cooler, contact your dealer to purchase and install them before turning on the computer.
(For the latest information about CPU, please visit: http://www.msi.com.tw/program/products/slim_pc/slm/pro_slm_cpu_support.php)
Important
Overheating
Overheating will seriously damage the CPU and system, always make sure the cooling fan can work properly to protect the CPU from overheating.
Replacing the CPU
While replacing the CPU, always turn off the power supply or unplug the power supplys power cord from grounded outlet first to ensure the safety of CPU.
Overclocking
This motherboard is designed to support overclocking. However, please make sure your components are able to tolerate such abnormal setting, while doing overclocking. Any attempt to operate beyond product speci­fications is not recommended. We do not guarantee the damages or risks caused by inadequate operation or beyond product specifications.
2-3
MS-6439 Barebone
Memory
These DIMM slots are used for installing memory modules.
(For more information on compatible components, please visit: http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php)
DIMM1~2
240-pin, 1.8V
56 x 2 = 112-pin
64 x 2 = 128-pin
Important
Each DIMM slot supports up to a maximum size of 1GB.
2-4
Hardware Setup
Power Supply
ATX 20-Pin Power Connector: ATX1
This connector allows you to connect to an power supply. To connect to the power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector.
11
20
ATX1
1
10
PIN SIGNAL
1 3.3V
2 3.3V
3 GND
4 5V
5 GND
6 5V
7 GND
8 PW_OK
9 5V_SB
10 12V
ATX 12V Power Connector: JPW1
This 12V power connector is used to provide power to the CPU.
Pin Definition
123
4
JPW1
Pin Definition
PIN SIGNAL
1 GND
2 GND
3 12V
4 12V
PIN SIGNAL
11 3.3V
12 -12V
13 GND
14 PS_ON
15 GND
16 GND
17 GND
18 -5V
19 5V
20 5V
Important
1. Make sure that all the connectors are connected to proper ATX power supplies to ensure stable operation of the mainboard.
2. Power supply of 350 watts (and above) is highly recommended for system stability.
3. ATX 12V power connection should be greater than 18A.
4. For this model, you must use a power supply that comes with a -5V pin supply.
2-5
MS-6439 Barebone
Front Panel
The Front Panel provides the following connectors:
Headphone
(Green)
(Pink)
USB PortsMicrophone
Audio Ports
These audio ports allow you to connect front audio devices.
USB Ports
The mainboard provides a UHCI (Universal Host Controller Interface) Universal Serial
Bus root for attaching USB devices such as keyboard, mouse or other USB-compat-
ible devices. You can plug the USB devices directly into these connectors.
2-6
Back Panel
The Rear Panel provides the following connectors:
Hardware Setup
LAN
USB Ports Keyboard
Mouse VGA Port
Serial Ports DVI Port
Line-In
Line-Out
Mic
RS-Out
CS-Out
SS-Out
LAN
The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN). You can connect a network cable to it.
Right LEDLeft LED
Left LED
Active LED
Right LED
10 / 100 / 1000M Speed LED
LED Color
10M Cable Plug-in
100M Cable Plug-in
1000M Cable Plug-in
No Transmission Transition
No Transmission Transition No Transmission
Transition
Yellow
OFF
Yellow, Blinking
OFF
Yellow, Blinking
OFF
Yellow, Blinking
Green / Orange
OFF
OFF
Green, Lighting
Green, Lighting
Orange, Lighting
Orange, Lighting
USB Port
The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard, mouse, or other USB-compatible devices.
Mouse / Keyboard
The standard PS/2® mouse/keyboard DIN connector is for a PS/2® mouse/keyboard.
2-7
MS-6439 Barebone
Serial Port
The serial port is a 16550A high speed communications port that sends/ receives 16 bytes FIFOs. You can attach a serial mouse or other serial devices directly to the connector.
VGA Port
The DB15-pin female connector is provided for monitor.
DVI Port
The DVI (Digital Visual Interface) connector allows you to connect a LCD monitor. It provides a high-speed digital interconnection between the computer and its display device. To connect an LCD monitor, simply plug your monitor cable into the DVI connector, and make sure that the other end of the cable is properly connected to your monitor (refer to your monitor manual for more information.)
Audio Ports
These audio connectors are used for audio devices. You can differentiate the color of the audio jacks for different audio sound effects.
Line-In (Blue) - Line In, is used for external CD player, tapeplayer or other
audio devices. Line-Out (Green) - Line Out, is a connector for speakers or headphones. Mic (Pink) - Mic, is a connector for microphones. RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode. CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode. SS-Out (Gray) - Side-Surround Out 7.1 channel mode.
2-8
Hardware Setup
Connectors
IDE Connector: IDE1
This connector supports IDE hard disk drives, optical disk drives and other IDE devices.
IDE1
Important
If you install two IDE devices on the same cable, you must configure the drives separately to Master / Slave mode by setting jumpers. Refer to IDE devices documentation supplied by the vendors for jumper setting instructions.
Card Reader Connector: CR1
The mainboard provides a connector to connect the Card Reader on the Front Panel.
CR1
2-9
MS-6439 Barebone
Serial ATA Connectors: SATA1 / SATA2
These connectors are high-speed Serial ATA interface port. Each connector can connect to one Serial ATA device.
SATA1 / SATA2
Fan Power Connectors: CPU_F1 / SYS_F2
The CPU_F1 (processor fan) and SYS_F2 (system fan) support system cooling fan with +12V. It supports three-pin head connector. When connecting the wire to the connectors, always take note that the red wire is the positive and should be con­nected to the +12V, the black wire is Ground and should be connected to GND. The mainboard has a Super I/O to detect CPU/fab temperature, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control.
GND +12V Sensor
Sensor
+12V GND
CPU_F1 SYS_F2
Important
Please refer to the recommended CPU fans at processors official website or consult the vendors for proper CPU cooling fan.
2-10
Hardware Setup
Front Panel Connector: JFP1
This connector is for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.
Pin Definition
Power Switch++
Power LED
-
10 9
2 1
JFP1
+
Reset
-
Switch
-
HDD LED
PIN
1
2
3
4
5
6
7
8
9
SIGNAL
HD_LED_P
FP PWR/SLP
HD_LED_N
FP PWR/SLP
RST_SW_N
PWR_SW_P
RST_SW_P
PWR_SW_N
RSVD_DNU
Hard disk LED pull-up
MSG LED pull-up
Hard disk active LED
MSG LED pull-up
Reset Switch low reference pull-down to GND
Power Switch high reference pull-up
Reset Switch high reference pull-up
Power Switch low reference pull-down to GND
Reserved. Do not use.
DESCRIPTION
CD-In Connector: JCD1
This connector is provided for external audio input.
R GND L
JCD1
SPDIF-Out Connector: J1 (For HDMI Graphics Card Audio Line Use Only)
This connector is used to connect SPDIF (Sony & Philips Digital Interconnect Format) interface for digital audio transmission to the HDMI graphics card.
GND
SPDF0
J1
2-11
MS-6439 Barebone
Jumper
Clear CMOS Jumper: JBAT1
There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. With the CMOS RAM, the system can auto­matically boot OS every time it is turned on. If you want to clear the system configuration, set the jumper to clear data.
1 3
Keep Data
1 3
Clear DataJBAT1
Important
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin position. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
2-12
Hardware Setup
Slot
PCI Express Slot: SLOT1 (For Riser Card Use Only)
The mainboard provides one PCI-X express slot. The PCI-X slot allows you to insert Riser Cards and the Riser Cards are included in the barebone. The Riser Cards allows you to insert PCI/PCI-E expansion card. You can insert any type of PCI cards and standard PCI-E to meet your needs. When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documenta­tion for the expansion card to make any necessary hardware or software settings.
Riser Card
2-13
System Assembly
Chapter 3
System Assembly
This chapter provides you with the information about sys­tem assembly procedures. While doing the installation, be careful in holding the components and follow the installa­tion procedures. Use a grounded wrist strap before handling computer components. Static electricity may damage the components.
ONLY FOR SERVICE PERSONEL
Always unplug the power cord before in­serting any add-on card or module.
3-1
MS-6439 Barebone
Overview
The built-in mainboard is designed for Hetis 900 Series Barebone only. Except the mainboard, the built-in components of the barebone include power supply. In this chapter we will show you how to install CPU, CPU Cooler, Memory Modules, Card Reader, Hard Disk Drive (HDD) and Optical Disk Drive (ODD).
Installation Tools
Cross type screwdriver, can be used to do most of the
installation. Choose one with a magnetic head would be better.
Pliers, can be used as an auxiliary tool to connect some con-
nectors or cables.
Forceps, can be used to pick up tiny screws or set up the
jumpers.
Rubber gloves, can prevent yourself from being incised and
suffering the static charge.
Installation Screws
Two types of screws are used in assembling the barebone: Round-headed screw
and thumb screw.
Round-headed screw: This type of screw is used to attach
the HDD and Card Reader to the tray.
3-2
System Assembly
Checking the Items
Before assembling your system, please check the items listed below for basic sys-
tem operation. The footstand and the CPU cooler are included in the package, other
items are optional.
Footstand
CPU (Optional) ODD (Optional)
HDD (Optional)
CPU Cooler
Memory Module (Optional)
Card Reader (Optional)
These pictures are for your refer-
ence only. Your packing contents may vary depending on the model you purchased.
3-3
MS-6439 Barebone
Installation Procedures
1. Removing Chassis Cover
Unlock the two screws on the back panel with hands.
Remove the chassis cover.
Press the level on the support bracket spring to release it.
Unlock the screw on the front panel to release the drive cage.
3-4
2. Installing Hard Disk Drive (HDD)
Lift the drive cage to slide aside.
Pull the HDD tray forwards to remove it from the chassis.
System Assembly
Put the HDD in the HDD tray and use four screws to fix it on both sides.
Connect the cable and the power cord to the HDD, then put the HDD tray back to secure it on the drive cage.
3-5
MS-6439 Barebone
3. Installing Optical Disk Drive (ODD)
Pull the lock brackets outwards on the both sides to release.
Insert the ODD and push the lock brack­ets back to fix it.
Connect the cable and the power cord to the ODD, then restore the drive cage.
Lock the screw on the front panel to fix the drive cage.
3-6
4. Installing Card Reader (Optional)
Use the screwdriver to unlock the card reader cage.
Insert the card reader into the cage with 15 degree angle.
System Assembly
Insert the LED into the cage and lock the card reader with two screws.
Restore the card reader back and con­nect the cable to the CR1 connector on the mainboard.
3-7
MS-6439 Barebone
5. Installing Memory Modules
Locate the DIMM slots.
Insert the DIMM vertically into the slot.
Note: The DIMM has only one notch on the center of module. It will only fit in the right direction.
3-8
6. Installing CPU
Locate the CPU socket. Pull the lever away from the socket and raise it up, then lift up the cover.
Put the CPU onto the socket.
Note: Make sure the pins are com­pletely embedded into the socket. The CPU can only fit in the correct direction.
System Assembly
Close the cover and the lever to com­plete the installaton.
3-9
MS-6439 Barebone
7. Installing CPU Cooler
Place the CPU cooler onto the CPU socket and secure the four screws.
Important
Do not fix any screw until all the four screws are in the position, and lock the four screws with balance, or it may shift the CPU position to cause the system unbootable.
Connect the CPU coolers power cord to the connector on the mainboard.
3-10
8. Restoring Chassis Cover
Restore the support bracket.
Restore the chassis cover.
System Assembly
Lock the chassis cover with the screws.
Horizontal typeTower type
3-11
MS-6439 Barebone
9. Installing Footstand
Lift up the PC and put the rubber feet into the pits on the footstand.
Make sure the rubber feet to get stuck on the footstand.
Put the PC on the footstand or lay on the rubber foots.
3-12
Chapter 4
BIOS Setup
This chapter provides information on the BIOS Setup pro­gram and allows you to configure the system for optimum use. You may need to run the Setup program when:
An error message appears on the screen during the
system booting up, and requests you to run SETUP.
You want to change the default settings for customized
features.
BIOS Setup
4-1
MS-6439 Barebone
Entering Setup
Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter SETUP
If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Important
1. The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only.
2. Upon boot-up, the 1st line appearing after the memory count is the BIOS version. It is usually in the format:
W7331VMS V1.0 070102 where:
1st digit refers to BIOS maker as A = AMI, W = AWARD, and P = PHOENIX. 2nd - 5th digit refers to the model number. 6th digit refers to the chipset as I = Intel, N = nVidia, and V = VIA. 7th - 8th digit refers to the customer as MS = all standard customers. V1.0 refers to the BIOS version. 070102 refers to the date this BIOS was released.
4-2
BIOS Setup
Control Keys
<> Move to the previous item <> Move to the next item <> Move to the item in the left hand <> Move to the item in the right hand
<Enter> Select the item
<Esc> Jumps to the Exit menu or returns to the main menu from a submenu
<+/PU> Increase the numeric value or make changes
<-/PD> Decrease the numeric value or make changes
<F6> Load Optimized Defaults
<F7> Load Fail-Safe Defaults
<F10> Save all the CMOS changes and exit
Getting Help
After entering the Setup menu, the first menu you will see is the Main Menu.
Main Menu
The main menu lists the setup functions you can make changes to. You can use the
arrow keys (↑↓) to select the item. The on-line description of the highlighted setup
function is displayed at the bottom of the screen.
Sub-Menu
If you find a right pointer symbol (as shown in the right view) appears to the left of certain fields that means a sub-menu can be launched from this field. A sub-menu contains additional
options for a field parameter. You can use arrow keys ( ↑↓ ) to highlight the field and
press <Enter> to call up the sub-menu. Then you can use the control keys to enter values and move from field to field within a sub-menu. If you want to return to the
main menu, just press the <Esc >.
General Help <F1>
The BIOS setup program provides a General Help screen. You can call up this screen from any menu by simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible selections for the highlighted item. Press <Esc> to exit the Help screen.
4-3
MS-6439 Barebone
The Main Menu
Standard CMOS Features
Use this menu for basic system configurations, such as time, date etc.
Advanced BIOS Features
Use this menu to setup the items of the special enhanced features.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your systems performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP / PCI Configurations
This entry appears if your system supports PnP/PCI.
4-4
BIOS Setup
PC Health Status
This entry shows your PC health status.
Frequency / Voltage Control
Use this menu to specify your settings for frequency / voltage control.
Load Fail-Safe Defaults
Use this menu to load the default values set by the BIOS vendor for stable system performance.
Load Optimized Defaults
Use this menu to load the default values set by the mainboard manufacturer specifi­cally for optimal performance of the mainboard.
Set Supervisor Password
Use this menu to set Supervisor Password.
Set User Password
Use this menu to set User Password.
Save & Exit Setup
Save changes to CMOS and exit setup.
Exit Without Saving
Abandon all changes and exit setup.
4-5
MS-6439 Barebone
Standard CMOS Features
Date (mm:dd:yy)
This allows you to set the system to the date that you want (usually the current date). The format is <day> <month> <date> <year>.
day Day of the week, from Sun to Sat, determined by BIOS. Read only. month The month from Jan. through Dec. date The date from 1 to 31 can be keyed by numeric function keys. year The year can be adjusted by users.
Time (hh:mm:ss)
This allows you to set the system time that you want (usually the current time). The time format is <hour> <minute> <second>.
IDE Channel 0 Master / Slave, IDE Channel 1 / 2 Master
Press <+> or <-> to select the hard disk drive type. The specification of harddisk drive will show up on the right hand according to your selection. Press <Enter> for the sub-menu of each item:
4-6
IDE HDD Auto-Detection
Press Enter to allow BIOS to auto-detect the type of the HDDs.
BIOS Setup
IDE Channel 0 Master
Press PgUp/<+> or PgDn/<-> to select Manual, None or Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually. If you select Manual, related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer.
Access Mode The settings are CHS, LBA, Large, Auto. Capacity The formatted size of the storage device. Cylinder Number of cylinders. Head Number of heads. Precomp Write precompensation. Landing Zone Cylinder location of the landing zone. Sector Number of sectors.
Halt On
The setting determines whether the system will stop if an error is detected at boot. When the system stops for the errors preset, it will halt on for 15 seconds and then automatically resume its operation. Available options are:
[All Errors] The system stops when any error is detected. [No Errors] The system doesnt stop for any detected error. [All, But Keyboard] The system doesnt stop for a keyboard error.
Base / Extended / Total Memory
The three items show the memory status of your system (read only).
4-7
MS-6439 Barebone
Advanced BIOS Features
CPU Feature
Press <Enter> and the following sub-menu appears:
Delay Prior to Thermal
When the CPU temperature reaches a factory preset level, a thermal monitor­ing mechanism will be enabled following the appropriate timing delay specified in this field. With the thermal monitoring enabled, clock modulation controlled by the processors internal thermal sensor is also activated to keep the proces­sor within allowable temperature limit.
4-8
BIOS Setup
Limit CPUID MaxVal
The item allows you to enable and disable the CPU ID maximum value.
[Enabled] Set to [Enabled] only when you have Prescott CPU and
NT4.0 operating system.
[Disabled] Set to [Disabled] if you have operating system other
than NT4.0.
C1E Function
When The CPU ID>0F40 and is above 533MHz/2.8GHz or 800MHz/3.6GHz, you can enable C1E Support to lower the CPU power consumption while idle. Settings: [Enabled], [Disabled].
Execute Disable Bit
Intel's Execute Disable Bit functionality can prevent certain classes of mali­cious "buffer overflow" attacks when combined with a supporting operating system. This functionality allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation.
Virtualization Technology (Only for the CPU with Dual Core)
Virtualization Technology will allow a platform to run multiple operating sys­tems and applications in independent partitions. With virtualization, one compu­ter system can function as multiple virtual systems. With enhancements to Intels various platforms, Intel Virtualization Technology can improve the ro­bustness and performance of todays software-only solutions.Settings: [Enabled], [Disabled].
Hard Disk Boot Priority
Press [Enter] to enter a sub menu which shows every current hard drive installed. Use [PageUp] or [PageDown] key to select the first boot hard disk.
4-9
MS-6439 Barebone
Virus Warning
The item is to set the Virus Warning feature for IDE Hard Disk boot sector protection. If the function is enabled and any attempt to write data into this area is made, BIOS will display a warning message on screen and beep.
Important
Many disk diagnostic programs that access the boot sector table can trigger the virus warning message. If you plan to run such a program, we recommend that you first disable the virus warning.
Quick Power On Self Test
Important
Select [Enabled] to reduce the amount of time required to run the power-on self-test (POST). A quick POST skips certain steps. We recommend that you normally disable quick POST. Better to find a problem during POST than lose data during your work.
First / Second / Third Boot Device
These items allow you to set the sequence of boot devices where BIOS attempts to load the operating system.
Boot Other Device
Setting the option to [Yes] allows the system to try to boot from other devices if the system fails to boot from the 1st/2nd/3rd boot device. Settings are: [Disabled], [Enabled].
Boot Up NumLock Status
This setting is to set the Num Lock status when the system is powered on. Setting to [On] will turn on the Num Lock key when the system is powered on. Setting to [Off] will allow users to use the arrow keys on the numeric keypad.
Typematic Rate Setting
When [Disabled], the following two items (Typematic Rate and Typematic Delay) are irrelevant. Keystrokes repeat at a rate determined by the keyboard controller in your system. When [Enabled], you can select a typematic rate and typematic delay.
Typematic Rate (Chars/Sec)
After Typematic Rate Setting is enabled, this item allows you to set the rate (characters/ second) at which the keys are accelerated.
Typematic Delay (Msec)
This item allows you to select the delay between when the key was first pressed and when the acceleration begins.
4-10
BIOS Setup
Security Option
This specifies the type of BIOS password protection that is implemented. Settings are described below:
Option Descripion
[Setup] The password prompt appears only when end users try to run Setup.
[System] A password prompt appears every time when the computer is
powered on or when end users try to run Setup.
Chassis Intrusion Detect
The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to [Reset]. The setting of the field will automatically return to [Enabled] later.
BIOS Protect
This function protects the BIOS from accidental corruption by unauthorized users or computer viruses. When enabled, the BIOS data cannot be changed when attempt­ing to update the BIOS with a Flash utility. To successfully update the BIOS, youll need to disable this Flash BIOS Protection function. You should enable this function at all times. The only time when you need to disable it is when you want to update the BIOS. After updating the BIOS, you should immediately re-enable it to protect it against viruses.
4-11
MS-6439 Barebone
Advanced Chipset Features
DRAM Clock / Drive Control
Press <Enter> and the following sub-menu appears:
Current FSB / DRAM Frequency
Those two items are read-only to show the current FSB and DRAM Frequency information.
DRAM Clock
Use this field to configure the clock frequency of the installed DRAM.
4-12
BIOS Setup
Important
The value plus a ratio (CPU: DDR) with parentheses means the non-synchronous overclocking.
DRAM Timing
The value in this field depends on performance parameters of the installed memory chips (DRAM). Do not change the value from the factory setting un­less you install new memory that has a different performance rating than the original DRAMs.
SDRAM CAS Latency
This controls the timing delay (in clock cycles) before SDRAM starts a read command after receiving it. [1.5] increases the system performance the most while [3.0] provides the most stable performance.
AGP & P2P Bridge Control
Press <Enter> and the following sub-menu appears:
VGA Share Memory Size
The system shares memory to the onboard VGA card. This setting controls the exact memory size shared to the VGA card.
Direct Frame Buffer
Frame Buffer is the video memory that stores data for video display (frame). This field is used to control the processors access to the section of system memory reserved for use by the integrated graphics processor as graphics memory.
[Enabled] The processor is allowed to directly write to the section of
system memory reserved as graphics memory. This in creases the performance of applications that write directly to the frame buffer.
[Disabled The processor is NOT allowed to directly write to the sec
tion of system memory reserved as graphics memory. This reduces the performance of applications that write directly to the frame buffer.
4-13
MS-6439 Barebone
Select Display Device
Use the field to select the type of device you want to use as the display(s) of the system.
CPU & PCI Bus Control
Press <Enter> and the following sub-menu appears:
PCI Master 0 WS Write
When [Enabled], writes to the PCI bus are executed with zero wait states.
PCI Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select [Enabled] to support compliance with PCI specifi­cation version 2.1.
VLink mode selection
This item lets you choose the speed mode between the North Bridge & South Bridge.
VLink 8X Support
This item enables or disables the 8X VLink Data Rate.
System BIOS Cacheable
Selecting [Enabled] allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result.
Init Display First
This item specifies which VGA card is your primary graphics adapter.
4-14
Integrated Peripherals
BIOS Setup
VIA OnChip IDE Device
Press <Enter> and the following sub-menu appears:
SATA Controller
This allows you to enable or disable onchip Serial ATA controller.
IDE DMA transfer access
Setting to [Enabled] will open DMA bus master and execute DMA action in DOS, which will make the data transferring faster.
4-15
MS-6439 Barebone
OnChip IDE Channel0
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Choose [Enabled] to activate each channel separately.
IDE Prefetch Mode
The onboard IDE drive interfaces support IDE prefetching, for faster drive accesses. When you install a primary and/or secondary add-in IDE interface, set this option to [Disabled] if the interface does not support prefetching.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select [Enabled] for automatic detection of the optimal number of block read/ writes per sector the drive can support.
VIA OnChip PCI Device
Press <Enter> and the following sub-menu appears:
Azalia HDA Controller
This setting is used to enable/disable the onboard audio controller.
Onboard Lan Device
This setting allows you to enable/disable the onboard LAN device.
4-16
BIOS Setup
Super IO Device
Press <Enter> and the following sub-menu appears:
Onboard Serial Port 1 / 2
Select a logical COM port name and matching address for the first and second serial ports. Select an address and corresponding interrupt for the first and second serial ports.
USB Device Setting
Press <Enter> and the following sub-menu appears:
USB 1.0 Controller
Select [Enabled] if your system contains a Universal Serial Bus (USB) control­ler and you have USB peripherals.
USB 2.0 Controller
Set to [Enabled] if you need to use any USB 2.0 device in the operating system that does not support or have any USB 2.0 driver installed, such as DOS and SCO Unix.
USB Operation Mode
Set to [High speed] if USB device was high speed device then it operated on high speed mode. Set to [Full/Low Speed] if USB device was full/low speed device then it operated on full/low speed mode.
4-17
MS-6439 Barebone
USB Keyboard Function
Select [Enabled] if your system contains a Universal Serial Bus (USB) control­ler and you have a USB keyboard.
USB Mouse Function
Select [Enabled] if you need to use a USB-interfaced mouse in the operating system.
USB Storage Support
Select [Enabled] if you need to use a storage device in the operating system.
4-18
Power Management Setup
BIOS Setup
ACPI function
This item is to activate the ACPI (Advanced Configuration and Power Management Interface) Function. If your operating system is ACPI-aware, such as Windows 98SE/ 2000/ME, select [Enabled].
Important
S3-related functions described in this section are available only when your BIOS supports S3 sleep mode.
ACPI Suspend Type
This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as Windows 98SE, Windows ME, Windows 2000 and Windows XP, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Options are:
4-19
MS-6439 Barebone
[S1/POS] The S1 sleep mode is a low power state. In this state,
no system context is lost (CPU or chipset) and hard ware maintains all system context.
[S3/STR] The S3 sleep mode is a lower power state where the
information of system configuration and open appli cations/files is saved to main memory that remains powered while most other hardware components turn off to save energy. The information stored in memory will be used to restore the system when a wake up event occurs.
Power Management Optional
This item is used to select the degree (or type) of power saving and is related to these modes: Suspend Mode and HDD Power Down. There are three options for power management:
[Min Saving] Minimum Power Management. Suspend Mode=1 Hour [Max Saving] Maximum Power Management. Suspend Mode=1 Min [User Define] Allows end users to configure each mode separately.
Video Off Option
This setting is used to control the mode in which the monitor will shut down. Setting options:
[Always On] Monitor remains on during power-saving modes. [Suspend -> Off] Monitor blanked when system enters Suspend mode. [Susp, Stby->Off] Monitor blanked when system enters either Suspend
or Standby mode.
[All Modes ->Off] Monitor blanked when system enters any power sav
ing mode.
Soft-Off by PWRBTN
This feature allows users to configure the power button function. Settings are:
[Instant-Off] The power button functions as a normal power-on/-
off button.
[By HardWare] When you press the power button, the computer en
ters the suspend/sleep mode, but if the button is pressed for more than four seconds, the computer is turned off.
AC Loss Auto Restart
This item specifies whether your system will reboot after a power failure or interrupt occurs. Setting options:
[Off] Leaves the computer in the power off state. [On] Leaves the computer in the power on state. [Former-sts] Restores the system to the status before power failure or
interrupt occurred.
4-20
BIOS Setup
Wakeup Event Detect
Press <Enter> to enter sub-menu and the following screen appears:
PS2KB Wakeup Key select
The item specifies how the system will be awakened from power saving mode when input signal of the keyboard is detected.
PowerOn by PCI Card
This controls how and whether the system can be powered on by the devices installed on PCI slots. Setting options: [Disabled], [Enabled].
Wake Up On Ring
These fields specify whether the system will be awakened from power sav­ing modes when activity or input signal of the specified hardware peripheral or component is detected.
Important
You need to install a modem card supporting power on function for Wake Up On Ring function.
RTC Alarm Resume
This is used to enable or disable the feature of booting up the system on a scheduled time/date from the S3, S4, and S5 power off state. Setting options: [Disabled], [Enabled].
Date (of Month)
The field specifies the date for RTC Alarm Resume. Settings: [0]~[31].
Resume Time (hh:mm:ss)
The field specifies the time for RTC Alarm Resume. Format is <hour><minute><second>.
4-21
MS-6439 Barebone
PnP / PCI Configurations
Reset Configuration Data
The ESCD (Extended System Configuration Data) NVRAM (Non-volatile Random Ac­cess Memory) is where the BIOS stores resource information for both PNP and non­PNP devices in a bit string format. When the item is set to [Enabled], the system will reset ESCD NVRAM right after the system is booted up and then set the setting of the item back to [Disabled] automatically.
Resources Controlled By
The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means abso­lutely nothing unless you are using a Plug and Play operating system such as Win­dows® 98/2000. If you set this field to [Manual], choose specific resources by going into each sub-menu that follows this field.
4-22
BIOS Setup
IRQ Resources
The items are adjustable only when Resources Controlled By is set to Manual. Press <Enter> and you will enter the sub-menu of the items. IRQ Resources list IRQ 3/4/5/7/ 9/10/11/12/14/15 for users to set each IRQ a type depending on the type of device using the IRQ. Settings are:
PCI Device For Plug & Play compatible devices designed for PCI bus
architecture.
Reserved The IRQ will be reserved for further request.
** PCI Express relative items **
Maximum Playload Size
This item allows you to set the PCI Express Maximum payload size per time. Settings are: [4096], [128], [256], [512], [1024], [2048].
4-23
MS-6439 Barebone
PC Health Status
Current System / CPU Temperature, SYS / CPU Fan Speed, Vcore, VCC5,
+12V, VCC3 (V), VBAT (V), 3VSB (V)
These items display the current status of all of the monitored hardware devices/ components such as CPU voltages, temperatures and all fans speeds.
4-24
Frequency / Voltage Control
BIOS Setup
CPU Clock Ratio
This setting controls the multiplier that is used to determine the internal clock speed of the processor relative to the external or motherboard clock speed.
Auto Detect PCI Clk
This item is used to auto detect the PCI slots. When set to [Enabled], the system will remove (turn off) clocks from empty PCI slots to minimize the electromagnetic inter­ference (EMI).
Spread Spectrum
When the motherboards clock generator pulses, the extreme values (spikes) of the pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves.
4-25
MS-6439 Barebone
Important
1. If you do not have any EMI problem, leave the setting at [Disabled] for optimal system stability and performance. But if you are plagued by EMI, select the value of Spread Spectrum for EMI reduction.
2. The greater the Spread Spectrum value is, the greater the EMI is reduced, and the system will become less stable. For the most suitable Spread Spectrum value, please consult your local EMI regulation.
3. Remember to disable Spread Spectrum if you are overclocking be­cause even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up.
4-26
BIOS Setup
Load Fail-Safe / Optimized Defaults
The two options on the main menu allow users to restore all of the BIOS settings to the default Fail-Safe or Optimized values. The Optimized Defaults are the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. The Fail-Safe Defaults are the default values set by the BIOS vendor for stable system performance.
When you select Load Fail-Safe Defaults, a message as below appears:
Pressing Y loads the BIOS default values for the most stable, minimal system performance.
When you select Load Optimized Defaults, a message as below appears:
Pressing Y loads the default factory settings for optimal system performance.
4-27
MS-6439 Barebone
Set Supervisor / User Password
When you select this function, a message as below will appear on the screen:
Type the password, up to six characters in length, and press <Enter>. The password typed now will replace any previously set password from CMOS memory. You will be prompted to confirm the password. Retype the password and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.
To clear a set password, just press <Enter> when you are prompted to enter the password. A message will show up confirming the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup without entering any password.
When a password has been set, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration.
4-28
Realtek ALC888 Audio
Appendix A
Realtek ALC888 Audio
The Realtek ALC888 provides 10-channel DAC that si­multaneously supports 7.1 sound playback and 2 chan­nels of independent stereo sound output (multiple streaming) through the Front-Out-Left and Front-Out­Right channels.
A-1
MS-6439 Barebone
Installing the Realtek HD Audio Driver
You need to install the driver for Realtek ALC888 codec to function properly before you can get access to 2-, 4-, 6-, 8- channel or 7.1+2 channel audio operations. Follow the procedures described below to install the drivers for different operating systems.
Installation for Windows 2000/XP
For Windows® 2000, you must install Windows® 2000 Service Pack4 or later before installing the driver. For Windows® XP, you must install Windows® XP Service Pack1 or later before installing the driver. The following illustrations are based on Windows® XP environment and could look slightly different if you install the drivers in different operating systems.
1. Insert the application CD into the CD-ROM drive. The setup screen will automati­cally appear.
2. Click Realtek HD Audio Driver.
Important
The HD Audio Configuration software utility is under continuous update to enhance audio applications. Hence, the program screens
shown here in this section may be slightly different from the latest software utility and shall be held for reference only.
A-2
Click here
Realtek ALC888 Audio
3. Click Next to install the Realtek High Definition Audio Driver.
4. Click Finish to restart the system.
Click here
Select this option
Click here
A-3
MS-6439 Barebone
Software Configuration
After installing the audio driver, you are able to use the 2-, 4-, 6- or 8- channel audio
feature now. Click the audio icon from the system tray at the lower-right corner of
the screen to activate the HD Audio Configuration. It is also available to enable the audio driver by clicking the Realtek HD Audio Manager from the Control Panel.
Double click
A-4
Realtek ALC888 Audio
Sound Effect
Here you can select a sound effect you like from the Environment list.
Environment Simulation
You will be able to enjoy different sound experience by pulling down the arrow, totally 23 kinds of sound effect will be shown for selection. Realtek HD Audio Sound Manager also provides five popular settings Stone Corridor, Bathroom, Sewer pipe, Arena and Audio Corridor for quick enjoyment.
You may choose the provided sound effects, and the equalizer will adjust automatically. If you like, you may also load an equalizer setting or make an new equalizer setting to
save as an new one by using the Load EQ Setting and Save Preset button, click Reset EQ Setting button to use the default value, or click Delete EQ Set- ting” button to remove a preset EQ setting.
There are also other pre-set equalizer models for you to choose by clicking Others under the Equalizer part.
A-5
MS-6439 Barebone
Equalizer Selection
Equalizer frees users from default settings; users may create their owned preferred settings by utilizing this tool.
10 bands of equalizer, ranging from 100Hz to 16KHz.
Save
The settings are saved permanently for future use.
Enable / Disable
To disable, you can tem­porarily stop the sound effect without losing the settings.
Delete
To delete the pre-saved settings which are created from previous steps.
Reset
10 bands of equalizer would go back to the default setting.
Load
Whenever you would like to use preload settings, simply click this, the whole list will be shown for your selection.
A-6
Realtek ALC888 Audio
Frequently Used Equalizer Setting
Realtek recognizes the needs that you might have. By leveraging our long experience at audio field, Realtek HD Audio Sound Manager provides you certain optimized equal­izer settings that are frequently used for your quick enjoyment.
[How to Use It] Other than the buttons Pop Live Club & Rock shown on the page, to pull down
the arrow in Others, you will find more optimized settings available to you.
Karaoke Mode
Karaoke mode brings Karaoke fun back home. Simply using the music you usually play, Karaoke mode can help you eliminate the vocal of the song or adjust the key to accommodate your range.
1.Vocal Cancellation: Single click on Voice Cancellation, the vocal of the song would be eliminated, while the background music is still in place, and you can be that singer!
2.Key Adjustment: Using Up / Down Arrow to find a key which better fits your vocal range.
Remove the human voice
Raise the key
Lower the key
A-7
MS-6439 Barebone
Mixer
In the Mixer part, you may adjust the volumes of the rear and front panels individually.
1. Adjust Volume
You can adjust the volume of the speakers that you pluged in front or rear panel by
select the Realtek HD Audio rear output or Realtek HD Audio front output
items.
Important
Before set up, please make sure the playback devices are well plugged in the jacks on the rear or front panel. The Realtek HD Audio front output item will appear after you pluging the speakers into the jacks on the front panel.
2. Multi-Stream Function
ALC888 supports an outstanding feature called Multi-Stream, which means you may play different audio sources simultaneously and let them output respectively from the indicated real panel or front panel. This feature is very helpful when 2 people are using the same computer together for different purposes.
Click the button and the Mixer ToolBox menu will appear. Then check the Enable playback multi-streaming and click OK to save the setup.
A-8
Realtek ALC888 Audio
Important
You have to plug audio device into the jacks on the rear and front panel first before enable the multi-stream function.
When you are playing the first audio source (for example: use Windows Media Player to play DVD/VCD), the output will be played from the rear panel, which is the default setting.
Then you must to select the Realtek HD Audio front output from the scroll list first, and use a different program to play the second audio source (for example: use
Winamp to play MP3 files). You will find that the second audio source (MP3 music) will come out from the Line-Out audio jack of Front Panel.
A-9
MS-6439 Barebone
3. Playback control
Tool Mute
Playback device
This function is to let you freely decide which ports
to output the sound. And this is essential when multi-
streaming playback enabled.
- Realtek HD Audio Rear Output
- Realtek HD Audio Front Output
Mute
You may choose to mute single or multiple volume controls or to completely mute sound output.
Tool
- Show the following volume controls
This is to let you freely decide which volume control items to be displayed.
- Advanced controls
- Enable playback multi-streaming With this function, you will be able to have an audio chat with your friends via headphone (stream 1 from front panel) while still have music (stream 2 from back panel) in play. At any given period, you can have maximum 2 streams operating simultaneously.
A-10
4. Recording control
Realtek ALC888 Audio
Tool Mute
Recording device
-Back Line in/Mic, Front Lin in
-Realtek HD Audio Input
Mute
You may choose to mute single or multiple volume controls or to completely mute sound input.
Tool
- Show the following volume controls
This is to let you freely decide which volume control items to be displayed.
- Enable recording multi-streaming
Important
ALC888 allows you to record the CD, Line, Mic and Stereo Mix channels simultaneously, frees you from mixing efforts. At any given period, you may choose 1 of the following 4 channels to record.
A-11
MS-6439 Barebone
Audio I/O
In this tab, you can easily configure your multi-channel audio function and speakers. You can choose a desired multi-channel operation here.
a. Headphone for the common headphone b. 2CH Speaker for Stereo-Speaker Output c. 4CH Speaker for 4-Speaker Output d. 6CH Speaker for 5.1-Speaker Output e. 8CH Speaker for 7.1-Speaker Output
Speaker Configuration:
1. Plug the speakers in the corresponding jack.
2. Dialogue connected device” will pop up for your selection. Please select the device you have plugged in.
- If the device is being plugged into the correct jack, you will be able to find the icon beside the jack changed to the one that is same as your device.
- If not correct, Realtek HD Audio Manager will guide you to plug the device into the correct jack.
A-12
Realtek ALC888 Audio
Connector Settings
Click to access connector settings.
Disable front panel jack detection (option)
Find no function on front panel jacks? Please check if front jacks on your system are so-called AC97 jacks. If so, please check this item to disable front panel jack detection.
Mute rear panel output when front headphone plugged in.
Enable auto popup dialogue, when device has been plugged in
Once this item checked, the dialog Connected device would automatically pop up when device plugged in.
A-13
MS-6439 Barebone
Test Speakers
You can select the speaker by clicking it to test its functionality. The one you select will light up and make testing sound. If any speaker fails to make sound, then check whether the cable is inserted firmly to the connector or replace the bad speakers
with good ones. Or you may click the auto test button to test the sounds of
each speaker automatically.
Center
Front Left
Front Right
Side Left Side Right
Subwoofer
Rear Left
Rear Right
A-14
Realtek ALC888 Audio
Microphone
In this tab you may set the function of the microphone. Select the Noise Suppres­sion to remove the possible noise during recording, or select Acoustic Echo Cancelltion to cancel the acoustic echo druing recording.
Acoustic Echo Cancelltion prevents playback sound from being recorded by mi-
crophone together with your sound. For example, you might have chance to use VOIP function through Internet with your friends. The voice of your friend will come out from speakers (playback). However, the voice of your friend might also be recorded into your microphone then go back to your friend through Internet. In that case, your friend will hear his/her own voice again. With AEC(Acoustic Echo Cancellation) enabled at your side, your friend can enjoy the benefit with less echo.
A-15
MS-6439 Barebone
3D Audio Demo
In this tab you may adjust your 3D positional audio before playing 3D audio applica­tions like gaming. You may also select different environment to choose the most suitable environment you like.
A-16
Realtek ALC888 Audio
Information
In this tab it provides some information about this HD Audio Configuration utility, including Audio Driver Version, DirectX Version, Audio Controller & Audio Codec. You
may also select the language of this utility by choosing from the Language list.
Also there is a selection Show icon in system tray . Switch it on and an icon will show in the system tray. Right-click on the icon and the Audio Accessories
dialogue box will appear which provides several multimedia features for you to take advantage of.
A-17
MS-6439 Barebone
Hardware Setup
Connecting the Speakers
When you have set the Multi-Channel Audio Function mode properly in the software utility, connect your speakers to the correct phone jacks in accordance with the setting in software utility.
n 2-Channel Mode for Stereo-Speaker Output
Refer to the following diagram and caption for the function of each phone jack on the back panel when 2-Channel Mode is selected.
Back Panel
1
2
4
1 Line-In
2 Line-Out (Front channels)
3 Mic
4 No function
5 No function
6 No function
5
3
6
A-18
n 4-Channel Mode for 4-Speaker Output
Back Panel
1
2
3
Realtek ALC888 Audio
4
5
6
4-Channel Analog Audio Output
1 Line-In
2 Line-Out (Front channels)
3 Mic
4 RS-Out (Rear surround channels)
5 No function
6 No function
A-19
MS-6439 Barebone
n 6-Channel Mode for 6-Speaker Output
Back Panel
1
4
2
3
6-Channel Analog Audio Output
1 Line-In
2 Line-Out (Front channels)
3 Mic
4 RS-Out (Rear surround channels)
5 CS-Out (Center and Subwoofer channel)
6 No function
5
6
A-20
n 8-Channel Mode for 8-Speaker Output
Realtek ALC888 Audio
1
Back Panel
2
4
5
3
6
8-Channel Analog Audio Output
1 Line-In
2 Line-Out (Front channels)
3 Mic
4 RS-Out (Rear surround channels)
5 CS-Out (Center and Subwoofer channel)
6 SS-Out (Side channels)
A-21
Loading...