MSI 848P-V2, MS-7157 Instruction Manual

i

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to correct the

interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission

limits.

VOIR LA NOTICE D’NSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International
MS-7157

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation

G52-M7157X1

ii

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every

care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our

products are under continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.

AMD, Athlon™ Athlon™XP, Thoroughbred™ and Duron™ are registered trademarks of AMD Corporation.

Intel® and Pentium® are registered trademarks of Intel Corporation.

PS/2 and OS® 2 are registered trademarks of International Business Machines Corporation.

Microsoft® is a registered trademark of Microsoft Corporation. Windows® 98/2000/NT/XP are registered

trademarks of Microsoft Corporation.

NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of NVIDIA

Corporation in the United States and/or other countries.

Netware® is a registered trademark of Novell, Inc.

Award® is a registered trademark of Phoenix Technologies Ltd.

AMI® is a registered trademark of American Megatrends Inc.

Kensington and MicroSaver are registered trademarks of the Kensington Technology Group.

PCMCIA and CardBus are registered trademarks of the Personal Computer Memory Card International

Association.

Revision History

Revision Revision History Date

V1.0 First release March 2005

iii

Safety Instructions

1. Always read the safety instructions carefully.

2. Keep this User Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the equipment from overheating.

Do not cover the openings.

6. Make sure the voltage of the power source and adjust properly 110/220V before connecting the

equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not place anything over the power

cord.

8. Always Unplug the Power Cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause electrical shock.

11. If any of the following situations arises, get the equipment checked by a service personnel:

- The power cord or plug is damaged.

- Liquid has penetrated into the equipment.

- The equipment has been exposed to moisture.

- The equipment does not work well or you can not get it work according to the User’ Manual.

- The equipment has dropped and damaged.

- The equipment has obvious sign of breakage.

12. Do not leave this equipment in an environment unconditioned, storage temperature above 60° C (140°F),

it may damage the equipment.

iv

Table of Contents

English.....................................................................1

Français...................................................................13

Deutsch....................................................................25

简体中文 ...................................................................37

繁體中文 ...................................................................49

日本語.......................................................................61

1

Introduction

Thank you for choosing 848P-V2 Series (MS-7157 v1.x) ATX mainboard. The 848P-V2 Series is
based on Intel® 848P & Intel® ICH5 chipsets for optimal system efficiency. Designed to fit the
advanced Intel® P4 Prescott processors in 478 pin package, the 848P-V2 Series delivers a high
performance and professional desktop platform solution.

Layout

2

Specifications

CPU

l Supports Intel® Pentium 4 Prescott processors in 478 pin package.
l FSB 400 / 533 / 800 MHz (FSB 400 for Northwood Celeron only).
l Supports up to 3.4GHz or higher speed.

(For the latest information about CPU, please visit
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php)

Chipset

l Intel® 848P chipset

- Supports FSB 800/533/400MHz.

- Supports AGP 8X interface.

- Supports DDR 400/333/266 memory interface.

l Intel® ICH5 chipset

- Hi-Speed USB (USB2.0) controller, 480Mb/sec, 8 ports.

- 2 Serial ATA/150 ports.

- 2 channel Ultra ATA 100 bus Master IDE controller.

- PCI Master V2.3, I/O APIC.

- Supports both ACPI and legacy APM power management.

Main Memory

l Supports two unbuffered DIMM of 2.5 Volt DDR SDRAM.
l Supports up to 2GB memory size without ECC.
l Supports Single channel DDR266/333/400 MHz.

(For the updated supporting memory modules, please visit
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php)

Slots

l One AGP slot supports 8x/4x at 1.5V (3.3V is not supported).
l Four 32-bit v2.3 Master PCI bus slots (support 3.3v/5v PCI bus interface).

On-Board IDE

l Dual Ultra DMA 66/100 IDE controllers integrated in ICH5.

- Supports PIO, Bus Master operation modes.

- Can connect up to four Ultra ATA drives.

l Serial ATA/150 controller integrated in ICH5.

- Up to 150MB/sec transfer speeds.

- Can connect up to two Serial ATA drives.

On-Board Peripherals

l On-Board Peripherals include:

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes

- 1 serial port on the rear panel

- 1 serial port with pinheader (through external cable)

- 1 parallel port supports SPP/EPP/ECP mode

- 8 USB 2.0 ports (Rear * 4/ Front * 4)

- 1 Line-In / Line-Out / Mic-In

- 1 RJ45 LAN jack

Audio

l AC97 link controller integrated in Intel® 848P chipset.
l 5.1-channel audio codec ADI AD1888.

- Compliance with AC97 v2.3 Spec.

- Meet PC2001 audio performance requirement.

3

LAN

l Broadcom® 4401

- Integrated Fast Ethernet MAC and PHY in one chip.

- Supports 10Mb/s, 100Mb/s.

- Compliance with PCI 2.2.

- Supports ACPI Power Management.

BIOS

l The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral devices

and expansion cards of the board automatically.

l The mainboard provides a Desktop Management Interface (DMI) function which records

your mainboard specifications.

Dimension

l ATX Form Factor: 30.5 cm (L) x 17.5 cm (W).

Mounting

l 6 mounting holes.

4

Rear Panel

The rear panel provides the following connectors:

Hardware Setup

This chapter tells you how to install the CPU, memory modules, and expansion cards, as well as
how to setup the jumpers on the mainboard. It also provides the instructions on connecting the
peripheral devices, such as the mouse, keyboard, etc. While doing the installation, be careful in
holding the components and follow the installation procedures.

Central Processing Unit: CPU

The mainboard supports Intel® Pentium 4 Prescott processor. The mainboard uses a CPU socket
called socket478. When you are installing the CPU, make sure to install the cooler to prevent
overheating. If you do not have the CPU cooler, contact your dealer to purchase and install them
before turning on the computer.
(For the latest information about CPU, please visit
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php.)

MSI Reminds You...
Overheating

Overheating will seriously damage the CPU and the system, always make sure the cooling fan
can work properly to protect the CPU from overheating.

Overclocking

This mainboard is designed to support overclocking. However, please make sure your
components are able to tolerate such abnormal setting, while doing overclocking. Any attempt to
operate beyond product specifications is not recommended. We do not guarantee the damages
or risks caused by inadequate operation or beyond product specifications.

Memory Speed/CPU FSB Support Matrix

Memory

FSB

DDR 266 DDR 333 DDR 400

400 MHz OK N/A N/A
533 MHz OK OK N/A

800 MHz N/A OK OK

5

CPU Installation Procedures for Socket 478

1. Please turn off the power and unplug the power cord before installing the CPU.

2. Pull the lever sideways away from the socket. Make sure to raise the lever up to a
90-degree angle.

3. Look for the gold arrow. The gold arrow should point towards the lever pivot. The CPU can
only fit in the correct orientation.

4. If the CPU is correctly installed, the pins should be completely embedded into the socket
and can not be seen. Please note that any violation of the correct installation procedures
may cause permanent damages to your mainboard.

5. Press the CPU down firmly into the socket and close the lever. As the CPU is likely to
move while the lever is being closed, always close the lever with your fingers pressing
tightly on top of the CPU to make sure the CPU is properly and completely embedded into
the socket.

Installing the CPU Fan

As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly important. To dissipate heat, you need to attach the CPU cooling fan and
heatsink on top of the CPU. Follow the instructions below to install the Heatsink/Fan:

1. Locate the CPU and its retention mechanism on the motherboard.

2. Position the heatsink onto the retention mechanism.

3. Mount the fan on top of the heatsink. Press down the fan until its four clips get wedged in
the holes of the retention mechanism.

4. Press the two levers down to fasten the fan. Each lever can be pressed down in only ONE
direction.

5. Connect the fan power cable from the mounted fan to the 3-pin fan power connector on
the board.

MSI Reminds You...

Overheating…
Overheating will seriously damage the CPU and system, always make sure the cooling fan can
work properly to protect the CPU from overheating.
Replacing the CPU…
While replacing the CPU, always turn off the ATX power supply or unplug the power supply’s
power cord from grounded outlet first to ensure the safety of CPU.

6

Memory

The mainboard provides two 184-pin unbuffered DDR 266 / DDR333 / DDR400 DDR SDRAM,
and supports the memory size up to 2GB. To operate properly, at least one DIMM module must
be installed. (For the updated supporting memory modules, please visit
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php)
Install at least one DIMM module on the slots. Memory modules can be installed on the slots in
any order. You can install either single- or double-sided modules to meet your own needs.
Installing DDR Modules

1. The DDR DIMM has only one notch on the center of module. The module will only fit in the
right orientation.

2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the socket.

3. The plastic clip at each side of the DIMM slot will automatically close.

Power Supply

The mainboard supports ATX power supply for the power system. Before inserting the power
supply connector, always make sure that all components are installed properly to ensure that no
damage will be caused. A 300W or above power supply is suggested.

ATX 20-Pin Power Connector: ATX1

This connector allows you to connect an ATX 20-pin power
supply. To connect the ATX 20-pin power supply, make sure
the plug of the power supply is inserted in the proper
orientation and the pins are aligned. Then push down the
power supply firmly into the connector.

ATX 12V Power Connector: JPW1

This 12V power connector is used to provide power to the CPU.

Floppy Disk Drive Connector: FDD1

The mainboard provides a standard floppy disk drive connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types.

Notch

Volt

11011

20

+3.3V

+3.3V

-12V

+3.3V

GND GND

PS-ON#

+5V
GND GND
GND +5V
GND GND

-5V

PWR OK

+5V 5VSB
+5V +12V

1

3

4

2

GND

12V

GND

12V

7

IDE Connector: IDE1/IDE2

The mainboard has dual Ultra DMA 66/100 controller that provides PIO mode 0~4, Bus
Master, and Ultra DMA 66/100 function. You can connect up to four hard disk drives,
CD-ROM, 120MB Floppy and other devices.
The first hard drive should always be connected to IDE1. IDE1 can connect a Master
and a Slave drive. You must configure second hard drive to Slave mode by setting the
jumper accordingly.

MSI Reminds You...

If you install two hard disks on one cable, you must configure the second drive to Slave mode by
setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper
setting instructions.

Serial ATA Connectors controlled by Intel® ICH5: SATA1/SATA2

The mainboard provides dual high-speed Serial ATA interface ports. The ports
supper 1st generation Serial ATA data rates of 150MB/s and are fully compliant
with Serial ATA 1.0 specifications. Each Serial ATA connector can connect to 1 hard disk device.

MSI Reminds You...

Please do not fold the serial ATA cable in a 90-degree angle, which will cause the loss of data
during transmission.

CD-In Connector: AUDIO2000

The connector is for CD-ROM audio connector.

Chassis Intrusion Switch Connector: JCI1

This connector is connected to a 2-pin chassis switch. JCI1 is
compliant with Intel® Front Panel I/O Connectivity Design Guide.

L

R

GND

8

Fan Power Connectors: CPUFAN1/PWRFAN1/SYSFAN1

The 3-pin CPUFAN1 (processor fan) and 3-pin
PWRFAN1 (power supply fan) / SYSFAN1
(system fan) support system cooling fan with
+12V. CPUFAN1 can support three- or four-pin
head connector.
When connecting the wire to the connectors, always take note that the red wire is the positive
and should be connected to the +12V, the black wire is Ground and should be connected to GND.
If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially
designed fan with speed sensor to take advantage of the CPU fan control.

MSI Reminds You...

Always consult the vendors for the proper CPU cooling fan.

Front Panel Connectors: JFP1/JFP2

The mainboard provides two front panel connectors for
electrical connection to the front panel switches and LEDs.
JFP1 is compliant with Intel® Front Panel I/O Connectivity
Design Guide.

Front Panel Audio Connector: JAUD1

The front panel audio connector allows you to
connect to the front panel audio and is
compliant with Intel® Front Panel I/O

Connectivity Design Guide.

MSI Reminds You...

If you do not want to connect to the front audio header, pins 5 & 6, 9 & 10 have
to be jumpered in order to have signal output directed to the rear audio ports.

Otherwise, the Line-Out connector on the back panel will not function.

Front USB Connector: JUSB1/JUSB2

The mainboard provides two standard USB 2.0 pin headers
JUSB1&JUSB2. USB2.0 technology increases data transfer
rate up to a maximum throughput of 480Mbps, which is 40
times faster than USB 1.1, and is ideal for connecting
high-speed USB interface peripherals such as USB HDD,

digital cameras, MP3 players, printers, modems, etc.

MSI Reminds You...

Please note that the pins of VCC & GND must be connected correctly or it may cause some
damage

GND
+12V
Sensor

+12V

Sensor

+12V
GND

GND

Sensor

CPUFAN1 SYSFAN1PWRFAN1

JFP1

Power

LED

HDD

LED

Reset

Switch

Power

Switch

1 9

2

10

JFP2

Power

LED

Speaker

1

728

(2)AUD_GND

AUD_VCC

AUD_RET_R

Key

AUD_RET_L(10)

(1)AUD_MIC

AUD_MIC_BIAS

AUD_FPOUT_R

HP_ON

AUD_FPOUT_L(9)

9

Serial Port Connector: JCOM1 (Optional)

The mainboard offers one 9-pin male DIN connector COM 1 (on the rear
panel), and one optional serial port JCOM1. Both are 16550A high speed
communication ports that send/receive 16 bytes FIFOs. You can attach a
serial mouse or other serial device directly to them.

PIN SIGNAL DESCRIPTION PIN SIGNAL DESCRIPTION

1
3
5
7
9

DCD

SOUT

GND
RTS

RI

Data Carry Detect
Receive Data Transmit
Data
Request To Send Ring
Indicate

2
4
6
8

10

SIN
DTR
DSR
CTS

X

Serial in or receive data
Serial out or transmit data
Data Set Ready
Clear To Send
X

Clear CMOS Jumper: JBAT1

There is a CMOS RAM on board that has a power supply from
external battery to keep the data of system configuration. With the
CMOS RAM, the system can automatically boot OS every time it is
turned on. If you want to clear the system configuration, use the
JBAT1 (Clear CMOS Jumper) to clear data. Follow the instructions
in the image to clear the data.

MSI Reminds You...

You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin position.
Avoid clearing the CMOS while the system is on, which will damage the mainboard.

AGP (Accelerated Graphics Port) Slot

The AGP slot allows you to insert the AGP
graphics card. AGP is an interface specification
designed for the throughput demands of 3D graphics. It introduces a 66MHz, 32-bit channel for
the graphics controller to directly access main memory. The slot supports AGP card for 8x/4x at

1.5v (3.3v is not supported).

PCI (Peripheral Component Interconnect) Slots

The PCI slots allow you to insert the expansion cards
to meet your needs. When adding or removing
expansion cards, make sure that you unplug the
power supply first. Meanwhile, read the documentation for the expansion card to make any
necessary hardware or software settings for the expansion card, such as jumpers, switches or
BIOS configuration.

PCI Interrupt Request Routing

The IRQ, abbreviation of interrupt request line and pronounced I-R-Q, are hardware lines over
which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically
connected to the PCI bus INT A# ~ INT D# pins as follows:

Order1 Order2 Order3 Order4
PCI Slot 1 INT B# INT C# INT D# INT A#
PCI Slot 2 INT C# INT D# INT A# INT B#
PCI Slot 3 INT D# INT A# INT B# INT C#
PCI Slot 4 INT A# INT B# INT C# INT D#

10

BIOS Setup

Power on the computer and the system will start POST (Power On Self Test) process. When the
message below appears on the screen, press <DEL> key to enter Setup.
DEL: Setup
If the message disappears before you respond and you still wish to enter Setup, restart the
system by turning it OFF and On or pressing the RESET button. You may also restart the system
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.

Main Page

Standard CMOS Features

Use this menu for basic system configurations, such as time, date etc.

Advanced BIOS Features

Use this menu to setup the items of Award special enhanced features.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system
performance.

Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup

Use this menu to specify your settings for power management.

PnP/PCI Configurations

This entry appears if your system supports PnP/PCI.

H/W Monitor

This entry shows the status of your CPU, fan, warning for overall system status.

Frequency/Voltage Control

Use this menu to specify your settings for frequency/voltage control.

Load Optimized Defaults

Use this menu to load the default values set by the mainboard manufacturer specifically for
optimal performance of the mainboard.

11

BIOS Setting Password

Use this menu to set password.

Save & Exit Setup

Save changes to CMOS and exit setup.

Exit Without Saving

Abandon all changes and exit setup.

Frequency/Voltage Control

Current CPU Clock
It shows the current clock of CPU. Read-only.

CPU Clock Ratio

This item allows you to adjust the CPU ratio. It might be locked by CPU hardware and this item
will be hided.

DDR Power Voltage

Adjusting the DDR voltage can increase the DDR speed. Any changes made to this setting may
cause a stability issue, so changing the DDR voltage for long-term purpose is NOT
recommended.

AGP Power Voltage

AGP voltage is adjustable in the field, allowing you to increase the performance of your AGP
display card when overclocking, but the stability may be affected. Setting options: 1.5V to 1.8V at

0.05V increment.

Auto Detect PCI Clk

This item is used to auto detect the PCI slots. When set to [Enabled], the system will remove
(turn off) clocks from empty PCI slots to minimize the electromagnetic interference (EMI).
Settings: [Enabled], [Disabled].

12

Spread Spectrum

When the motherboard’s clock generator pulses, the extreme values (spikes) of the pulses
creates EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI
generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves.
If you do not have any EMI problem, leave the setting at [Disabled] for optimal system stability
and performance. But if you are plagued by EMI, select the desired range for EMI reduction.
Remember to disable Spread Spectrum function if you are overclocking, because even a slight
jitter can introduce a temporary boost in clock speed which may just cause your overclocked
processor to lock up.

CPU Clock

This item allows you to select the CPU Front Side Bus clock frequency (in MHz) and overclock
the processor by adjusting the FSB clock to a higher frequency.

Load BIOS Defaults

You can load the default values provided by the mainboard manufacturer for the stable
performance.

13

Introduction

Félicitations, vous venez d’acquérir une carte mère ATX 848P-V2 Series (MS-7157 v1.x) La
848P-V2 Series est basée sur les Chipsets Intel® 848P & Intel® ICH5 offrant un système très
performant. La carte fonctionne avec les processeurs Intel® P4 Prescott 400/533/800MHz
(Socket 478), est très performante et offre une solution adaptée tant aux professionnels qu’aux
particuliers.

Schéma

14

Spécificités

CPU

l Supporte les processeurs Intel® P4 Northwood/Prescott (Socket 478) jusqu’à 3.4 ghz
(Pour les dernières mises à jours concernant les CPU, vous pouvez visiter :

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php.)

Chipset

l Chipset Intel® 848P

- Supporte FSB 800/533/400MHz.

- Supporte l’interface AGP 8X.

- Supporte l’interface de mémoire DDR 400/333/266.

l Chipset Intel® ICH5

- contrôleur Hi-Speed USB (USB2.0), 480Mb/sec, 8 ports.

- 2 ports Serial ATA/150.

- 2 contrôleurs IDE bus Master channel Ultra ATA 100.

- PCI Master V2.3, I/O APIC.

- Supporte à la fois l’ACPI et la gestion de l’alimentation (APM).

Mémoire Principale

l Supporte deux DIMM unbuffered de2.5 Volt DDR SDRAM.
l Supporte jusqu’à 2GB de mémoire non ECC.
l Supporte le seul canal DDR266/333/400 MHz.

(Pour nue mise à jour sur les modules de mémoires supportés, veuillez visiter
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php )

Slots

l Un slot AGP supportant 8x/4x à 1.5V (le 3.3V n’est pas supporté).
l Quatre slots PCI bus Master 32-bit v2.3 (supporte l’ interface bus PCI 3.3v/5v).

IDE Intégré

l Deux contrôleurs IDE Ultra DMA 66/100 intégrés dans ICH5.

- Supporte les modes opératoires PIO, Bus Master.

- Possibilité de connecter jusqu’à quatre disques Ultra ATA.

l Contrôleur Serial ATA/150 intégré dans ICH5.

- Vitesse de transfert jusqu’à 150MB/sec.

- Peut connecter jusqu’à deux disques Serial ATA.

Périphériques Intégrés

l Périphériques Intégrés Inclus:

- 1 port floppy supportant 1 FDD avec 360K, 720K, 1.2M, 1.44M et 2.88Mbytes

- 1 port série sur le panneau arrière

- 1 port série sur broches à travers un câble externe

- 1 port parallèle supportant les modes SPP/EPP/ECP

- 8 ports USB 2.0 (Arrière * 4/ Avant * 4)

- 1 Line-In / Line-Out / Mic-In

- 1 RJ45 LAN jack

Audio

l Contrôleur AC97 link integré dans le chipset Intel® 848P.
l 5.1 canaux audio codec ADI AD1888.

- Compatible avec les Spec AC97 v2.3.

- Répond aux exigences audio PC2001.

15

LAN

l Broadcom® 4401

- Fast Ethernet MAC et PHY Integré dans une puce.

- Supporte 10Mb/s, 100Mb/s.

- Compatible avec PCI 2.2.

- Supporte l’ACPI Power Management.

BIOS

l La carte procure un BIOS “Plug & Play” qui détecte automatiquement les cartes

d’extension ou les périphériques.

l La carte offre une interface DMI (Desktop Management Interface) qui enregistre les

spécificités de la carte mère.

Dimension

l Format ATX : 30.5 cm (L) x 17.5 cm (W).

Montage

l 6 trous de montage.

16

Panneau Arrière

Le panneau arrière procure les connecteurs suivants:

Installation Matériel

Ce chapitre vous indique comment installer le CPU, la mémoire ainsi que les cartes d’extension
ou encore le réglage des cavaliers présents sur la carte. Vous aurez aussi des instructions
relatives à la connexion des périphériques tels que la souris, le clavier etc. Lors de l’installation
veuillez faire très attention aux éléments composant la carte mère et suivez bien les procédure
d’installations.

Central Processing Unit: CPU

La carte mère supporte les processeurs Intel Pentium 4/Celeron(D) (socket 478). La carte mère
utilise un socket appelé PGA478 permettant une installation aisée du processeur. Lors de
l’installation du CPU, assurez-vous que le CPU possède bien un système de refroidissement
constitué d’un dissipateur + ventilateur permettant la dissipation de la chaleur. Pour connaître le
modèle de ventilateur nécessaire à la bonne utilisation de votre système n’hésitez pas à
contacter votre revendeur. (Pour connaître les dernières informations concernant le CPU,
veuillez visiter
(http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php)

Exemple de Dérivation du CPU Core Speed

Si Horloge CPU = 133MHz

Ration Core/Bus = 23
Alors Vitesse CPU = Horloge x ratio Core/Bus
= 133MHz x 23
= 3.06 GHz

Tableau de support de vitesse mémoire / CPU FSB

Memory

FSB

DDR 266 DDR 333 DDR 400

400 MHz OK N/A N/A
533 MHz OK OK N/A

800 MHz N/A OK OK

Procédure d’Installation du CPU Socket 478

1. Veuillez éteindre ou débrancher le PC avant d’installer le CPU.

2. Tirer le levier qui se trouve sur le côté du socket. Assurez-vous que celui-ci est bien relevé
(position 90°).

3. Chercher la marque dorée sur le CPU. La marque dorée doit pointer vers le pivot du levier.

17

Le CPU peut ne s’installer que dans une seule position.

4. Si le CPU est correctement installé, les pattes doivent être complètement insérées dans le
socket et ne plus être visibles. Veuillez noter qu’une mauvaise installation endommage à
coup sur le processeur ainsi que la carte mère.

5. Appuyer sur le CPU et baisser le levier. Ainsi le CPU ne peut plus bouger et reste fixe sur

le socket.

Installation du Ventilateur de CPU

La technologie faisant augmenter rapidement la vitesse des nouveaux CPU, il devient donc
nécessaire de prêter attention à la dissipation thermique (refroidissement du CPU). C’est la
raison pour laquelle vous devez installer un système de refroidissement en phase avec votre
processeur. Suivez les instructions ci dessous afin d’installer votre système de refroidissement :

1. Localiser le CPU et son système de rétention sur la carte mère.

2. Positionner le dissipateur au dessus du mécanisme de rétention du CPU.

3. Monter le ventilateur sur le dissipateur. Appuyer sur l’ensemble jusqu’à ce que vous
puissiez attacher le ventilateur au mécanisme de rétention.

4. Appuyer sur les deux leviers du ventilateur. Chaque levier ne peut se manipuler que dans
un seul sens.

5. Connecter le câble d’alimentation sur le connecteur de la carte mère prévu à cet effet (3
broches).

MSI Vous Rappelle...

Surchauffe

La surchauffe endommagera le CPU ainsi que le système, c’est pourquoi il faut un ventilateur
adéquat afin de protéger votre PC.

Remplacer le CPU

Lorsque vous remplacez les CPU, veuillez toujours couper le courant ou débrancher la prise
pour éviter tout problème et ne pas endommager votre PC.

Mémoire

La carte mère possède deux slots (184 broches) pour modules de mémoire DDR 266 / DDR333 /
DDR400 DDR SDRAM, et supporte un maximum de mémoire jusqu’à 2GB. Pour fonctionner
correctement, il faut au moins installer un module de mémoire DIMM. (Pour les dernières mises
à jours de mémoire supportées, merci de visiter
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php )
Installer au moins un module DIMM sur les slots. L’installation des modules de mémoires n’a pas
de sens particulier. Vous pouvez installer soit des modules simples ou doubles faces selon vos
besoins.

1. Le DDR DIMM ne possède qu’une encoche en son centre. Ainsi il n’est possible de
monter le module que dans un seul sens.

2. Insérez le module de mémoire DIMM verticalement dans le slot. Puis

appuyez dessus

3. Le clip en plastique situé de chaque côté du module va se fermer

automatiquement.

Notch

Volt

18

Alimentation

La carte mère supporte les alimentations ATX. Avant de brancher le connecteur d’alimentation,
Il faut toujours vous assurer que tous les composants sont bien installés afin de ne pas les
endommager. Une alimentation 300W ou supérieur est préconisée.

Connecteur d’Alimentation ATX 20 Broches : ATX1

Ce connecteur vous permet de connecter l’alimentation ATX. Pour ce
faire assurez-vous que le connecteur est bien positionné dans le bon
sens. Puis appuyer sur le câble.

Connecteur d’alimentation ATX 12V : JPW1

Le connecteur d’alimentation 12V est utilisé pour alimenter le CPU

Connecteur Floppy Disk Drive: FDD1

La carte offre un connecteur standard floppy disk drive (lecteur de
disquette) qui supporte les disques 360K, 720K, 1.2M, 1.44M et

2.88M

Connecteur IDE: IDE1/IDE2

La carte mère possède un contrôleur 32-bit Enhanced PCI IDE et Ultra DMA
66/100/133 qui procure les fonctions PIO mode 0~4, Bus Master, et Ultra DMA
33/66/100/133. Vous pouvez connecter jusqu’à 4 matériels (disques durs, CD-ROM,
120MB Floppy).

Le premier disque dur doit être connecté sur l’IDE1. L’IDE1 peut recevoir un matériel
Maître et un Esclave. Vous devez configurer le second disque en mode Esclave et ce à
l’aide du cavalier situé à l’arrière.

MSI Vous Rappelle...
Si vous voulez installer deux disques durs, vous devez configurer le second en Esclave
en configurant le cavalier. Se référer à la documentation du disque dur pour les
instructions.

Connecteurs Serial ATA contrôlés par Intel® ICH5: SATA1/SATA2

La carte mère procure deux ports d’interface haute vitesse Serial ATA. Elle
supporte la 1e génération de serial ATA (taux de transfert 150 MB/s).
Ces quatre connecteurs sont entièrement compatibles avec le Serial ATA 1.0. Chaque
connecteur peut être connecté à un disque dur..
Le Southbridge de cette carte est Intel ICH6, qui supporte quatre connecteurs de série SATA1 ~
SATA4. SATA1 ~ SATA4 sont deux ports d’interface dual high-speed Serial ATA. Chacun

11011

20

+3.3V

+3.3V

-12V

+3.3V

GND GND

PS-ON#

+5V
GND GND
GND +5V
GND GND

-5V

PWR OK

+5V 5VSB
+5V +12V

1

3

4

2

GND

12V

GND

12V

19

MSI Vous Rappelle...

Ne pas tordre le câble à 90° afin de ne pas l’endommager et éviter les pertes de données lors du
transfert.

Connecteur CD-In: AUDIO2000

Le connecteur est destiné au branchement audio du CD-ROM

Connecteur Chassis Intrusion Switch: JCI1

Ce connecteur est connecté à deux broches chassis switch. JCI1
est compatible avec l’Intel® Front Panel I/O Connectivity Design
Guide.

Connecteurs d’alimentation de ventilateur:
CPUFAN1/PWRFAN1/SYSFAN1

Le CPUFAN1 (Ventilateur de processeur) et le
PWRFAN1 (ventilateur d’alimentation) /
SYSFAN1 (ventilateur de système) supporte le
+12V. CPUFAN1 peut supporter 3 ou 4 broches.
Lors de la connexion du câble, assurez-vous
que le fil rouge soit connecté au +12V et le fil noir connecté au “GND“. Si la carte mère possède
un système de gestion intégré, vous devez utiliser un ventilateur ayant ces caractéristiques si
vous voulez contrôler le ventilateur du CPU

MSI Vous rappelle...

Il faut toujours consulter votre revendeur au sujet du ventilateur

Connecteurs Front Panel: JFP1/JFP2

La carte mère procure 2 connecteurs pour les branchements
électriques (LED disque dur…). JFP1 est compatible avec le

Design Intel Front Panel I/O Connectivity Design Guide

Connecteur Front Panel Audio: JAUD1

Le connecteur audio JAUD1 vous permet de
connecter l’audio en façade et est compatible
avec lntel ® Front Panel I/O Connectivity

Design Guide

MSI Vous rappelle...

Si vous ne voulez pas connecter l’audio en façade à l’aide des broches 5 & 6,
9 & 10 doivent être recouvertes par un cavalier pour envoyer le signal vers les
ports audio à l’arrière. Autrement le connecteur Line-Out à l’arrière ne fonctionnera pas.

L

R

GND

GND
+12V
Sensor

+12V

Sensor

+12V
GND

GND

Sensor

CPUFAN1 SYSFAN1PWRFAN1

JFP1

Power

LED

HDD

LED

Reset

Switch

Power

Switch

1 9

2

10

JFP2

Power

LED

Speaker

1

728

(2)AUD_GND

AUD_VCC

AUD_RET_R

Key

AUD_RET_L(10)

(1)AUD_MIC

AUD_MIC_BIAS

AUD_FPOUT_R

HP_ON

AUD_FPOUT_L(9)