Mr. Steam SAH6000C1, SAH6000B1 Specifications
®
1
1
⁄
2
”(38)
5
5
⁄
8
”
(138)
7
3
⁄
4
”
(
197)
1
1
⁄
4
”
(32)
12”
(305)
14
7
⁄
8
”
(378)
1
7
⁄
8
”
(48)
3
3
⁄
8
”(86)
5
3
⁄
16
” (132)
2
1
⁄
2
”
(64)
14
3
⁄
8
”(365)
mr.steam
Technical Specifications
______________________________________________________
Model SAH6000
Mr.Steam Standard Features
Ideal for starter homes and guest baths
•
• Ideal for ceramic, porcelain, glass tiles & acrylic enclosures
• Rugged stainless steel generator with electronic
printed circuit board available in 208V or 240V 1 Phase
• Uses less than one gallon of water for a 20-minute session
• 23% more compact than standard MS steam generators
• Integral safety time-out feature
• Built-in drain valve
• Made in the USA
Safety Features
• Built-in, low-voltage 24-volt control
• ASME safety valve
• 60-minute electronic countdown
shutdown with 75-minute limiting
safety back-up
Locating and Installing the Steam Generator Unit
• Select a location as near as practical to the steam room, within 60
feet. Typical locations include:
closet, vanity cabinet, heated attic
or basement
• Do not install steambath generator
inside the steam room.
• Do not install steambath generator
outdoors or wherever environmental conditions may affect the
safety and/or performance of the
generator
• Do not install steambath
generator or plumbing lines in unheated attic or any locations where
water could freeze
• Do not install steambath generator
near flammable or corrosive materials or chemicals or in areas having
a high concentration of chlorine
• Install steambath generator on a
solid and level surface or securely
mounted to a wall using the keyhole slots provided.
• Install steambath generator in an
upright position only
•
Provide a minimum of (12) inches at
both ends and top of the steam generator or as required for servicing
• Provide unions as required to facilitate installation and disconnection
of the steam generator.
Required Plumbing
Steam Outlet (3/8" NPT) Safety Valve (3/4" NPT)
Drain (1/4" NPT) Steam Head (1/2" NPT)
Water Supply (3/8" NPT)
Water Inlet
™
SteamStart
Connection
S
team Outlet
Safety Valve
Manual
Drain Valve
Electrical
All electrical wiring to be installed by a qualified
licensed electrician in accordance with National
Electrical Code and local electrical code.
Power Wiring
1. Check power voltage. Use 240V rated unit when
supply matches rating of unit before installation.
2. Use minimum 90˚ C/300 V rated insulated copper
conductors only, type THHN or equal sized in
accordance with National Electrical Code and local
electrical code for the Amps in Ampere Chart.
If allowed by code, NM cable may require a larger
wire size than as listed on the chart.
3. Connect suitably sized equipment grounding wire to
ground terminal provided.
4. Install a separate circuit breaker between supply and
unit. Provide a power supply disconnect within
sight of the steam generator or one that is capable
of being locked in the open position.
A M P E R E C H A R T
MODEL NO. VOL. CU.FT. KW 1 PH PHASE AMPS (AWG)*
SAH6000 150 6.0 208 1 29 8
MAX ROOM VOLTS WIRE SIZE
240 1 25 8
* for up to 45˚C ambient
FOR ILLUSTRATIVE PURPOSES ONLY.
IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and Maintenance
Manual or refer to the manual provided with the unit.
MODEL VOLTAGE* PROJECT INFORMATION
SAH6000
*
Steam@Home units are only available
in single phase
B=208
C=240
Location:
Architect:
Engineer:
Notes:
Optional Equipment: AudioWizard, ChromaSteam, Recessed Light, MS Light, MS Wallseat, Drip Pan, Chlorine Filter, FORM Shower Systems
mr.steam
43-20 34th Street, Long Island City, NY 11101 TEL: 800 76 STEAM FAX: 718 472 3256 / 9410 S. La Cienega Blvd. Inglewood CA 90301 TEL:800 72 STEAM FAX: 310 216 2944
®
Sussman-Automatic Corp
®
hello@mrsteam.com www.mrsteam.com
Contractor:
Submitted By:
Date:
TS0045-6000 REV 5.14
Loading...