Page 1
Installation, Operation and Maintenance Manual
Steambath Generator Systems
Residential
Models: MS90E – MS400E and MSSUPER1E – 6E
____________________
IMPORTANT:
Leave this material with the home owner.
____________________
mr.steam
®
®
Feel Good Inc.
CAUTION
!
installation, operation and maintenance manual supplied with the product must be used for
installation, operation and maintenance purposes. Failure to use the installation, operation and
maintenance manual supplied with the product may result in a property damage or personal injury.
This installation, operation and maintenance manual is for general reference. The
Page 2
EA D M E F IRS T!
R
WARNING
!
instructions, you will notice warning and
caution symbols. This blocked information is
important for the safe and efficient installation and operation of this generator. These
are types of potential hazards that may
occur during installation and operation:
WARNING
!
hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
!
ardous situation, which, if not avoided may result in
minor or moderate injury or product damage.
IMPORTANT NOTE:
information that is especially relevant to a problemfree installation.
ll information in these instructions is based on
A
he latest product information available at the
t
time of publication. Sussman-Automatic Corporation
reserves the right to make changes at any time
without notice.
As you follow these
Indicates a potentially
Indicates a potentially haz-
his highlights
T
When installing and using this electrical equipment, basic safety precautions should
always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
.
1
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
2.
!
WARNING
3.
!
injury or death if improperly used. Steam rooms
contain steam and elevated temperatures.
Please read and observe all warnings in this
manual before installing or using a steam room.
WARNING
4.
!
A. The wet surfaces of steam enclosures
may be slippery. Use care when entering
or leaving.
B. The steam head is hot. DO NOT touch the
steam head and avoid the steam near
the steam head.
C. Prolonged use of the steam system can raise
excessively the internal human body temperature and impair the body’s ability to regulate its internal temperature (hyperthermia).
Limit your use of steam to 10-15 minutes
until you are certain of your body’s
reaction.
Supervise children at all times
Steam is hot and can cause
To reduce the risk of injury:
D. Excessive temperatures have a high
potential for causing fetal damage during the early months of pregnancy.
Pregnancy or possibly pregnant women
should consult a physician regarding
correct exposure.
E. Obese persons and persons with a his-
tory of heart disease, low or high blood
pressure, circulatory system problems,
or diabetes should consult a physician
before using a steambath.
F. Persons using medication should con-
sult a physician before using a steambath since some medication may
induce drowsiness while other medications may affect heart rate, blood pressure and circulation.
SAVE THESE INSTRUCTIONS
HYPERTHERMIA occurs when the internal temperature of the
body reaches a level several degrees above the normal body
temperature of 98.6° F. The symptoms of hyperthermia
include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness, and fainting. The effects of
hyperthermia include:
WARNING
!
Not Actual Size
The use of alcohol, drugs, or medication can greatly increase the risk of hyperthermia.
The manual supplied with the generator includes a peel and stick warning label. Its
proper use is an essential part of providing a safe environment for steam room users.
The peel and stick warning label must be applied to the wall of the shower or steam
enclosure, at a point that is visible to all users. Failure to install this sticker may result in
serious injury or death. The location where this owner's manual is kept shall be written
in the space provided on the label using permanent ink. For a replacement warning
label contact MrSteam customer service at 1-800-76-STEAM or hello@mrsteam.com.
a) Failure to perceive heat;
b) Failure to recognize the need to exit the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath; and
f) Unconsciousness.
Designed, Engineered
and Assembled in the
# # # #
USA
mr.steam
43-20 34th Street, Long Island City, NY 11101 TEL: 1 800 76 STEAM FAX: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 TEL: 1 800 72 STEAM FAX: 310 216 2944
®
Sussman-Automatic Corporation®hello@mrsteam.com www.mrsteam.com
PUR 100472A Rev 8.18
Page 3
RESIDENTIAL STEAMBATH GENERATOR SYSTEMS
INSTALLATION, OPERATION & MAINTENANCE MANUAL
MODEL _______________________________
MODELS: MS-90E, MS-150E, MS-225E, MS-400E, MS-SUPER 1E,
S-SUPER 2E, MS-SUPER 3E, MS-SUPER 4E, MS-SUPER 5E, MS-SUPER 6E
M
TABLE OF CONTENTS
Important Safety Instructions . . . . . . . . . . . . . Inside front cover
Select Your MrSteam Model . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Generator Specification Chart . . . . . . . . . . . . . . . . . . . . . . . . . 2
_______________________________________________________________________
INSTALLER SECTION
Before Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Steam Room Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Water Quality Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Locating the Steam Generator . . . . . . . . . . . . . . . . . . . . . . . 4
Typical Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . 5
Installation: Plumbing, Water Supply, Drain, Steam Outlet
Safety Valve, Drip Pan, AromaSteam . . . . . . . . . . 6
Steam Head Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Steam Generator Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical Specifications & Field Power Wiring . . . . . . . . . . . 9
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Optional Tandem Cable Diagram . . . . . . . . . . . . . . . . . . . . 11
Initial Start-Up & Checkout . . . . . . . . . . . . . . . . . . . . . . . . . 12
Optional & Accessary Equipment . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System Status Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Liquid Level Control Board . . . . . . . . . . . . . . . . . . . . . . . . . 13
Optional AutoFlush System . . . . . . . . . . . . . . . . . . . . . . . . . 14
Optional Drip Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Optional Express Steam . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts Identification Diagrams. . . . . . . . . . . . . . . . . . . . . . . . 16
Replacement Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CONTROL INSTALLATION
Before Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Control Rough-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
_______________________________________________________________________
SERIAL NO. ___________________________
HOMEOWNER SECTION
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . 19
Setting Steam Bath Temperature & Duration . . . . . . . . . . . 20
Safety & Operating Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Care Tips for Controls and Generator Maintenance . . . . . . 20
Using the AromaSteam Essential Oils . . . . . . . . . . . . . . . . . 21
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
®
mr.steam
Feel Good Inc.
Page 4
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
SELECT YOUR MrSteam
MrSteam @ Your Fingertips:
Start working smarter with MrSteam’s mobile sizing app,
now available for the iPad
Visit mrsteam.com to size your generator automatically
or go directly to: http://isizing.mrsteam.com
Materials of construction, room size and special design features such
s large glass areas, all affect
a
1.
Measure length, width & height in feet of the steam/shower or tub/shower
Multiply the Length ____ x Width_____ x Height _____ =
2.
Construction Materials:
For natural stones: natural marble, Add 110%
stone, shale, glass block or concrete
For ceramic or porcelain tile on Add 40%
cement board or mortar bed
3.
Ceiling Height: For each foot above 8 feet Add 15%
4. Add all figures above to obtain the Total Room Volume required
Compare your Room Volume to the Chart below
®
, iPod®and most smart phones.
he steam generator model selection.
t
and select the appropriate model.
ROOM VOLUME
WARNING
!
se of this steambath system, please note that if
u
In considering the purchase or
you are pregnant, have a coronary condition, are
in poor health, are being treated for any other
medical condition, or are using medication or
drugs, MrSteam recommends that you obtain the
approval of a physician before use.
For information about this product and safety
issues, please call 1.800.76.STEAM
IMPORTANT NOTES:
or steam rooms constructed of acrylic or
F
synthetic materials, select next lower-rated
MS model.
The MrSteam Sizing Chart allows for up to 60 feet
of insulated steam line from the MS generator to
the steam room. If the 60 foot line is exceeded
consult with factory. The steam generator control
locations must be taken into account. A 30 foot
cable is standard. Contact MrSteam to purchase
an optional 60 ft. cable PN 103990-60 for
®
iTempo
iSteam
and AirTempo®and PN 104117-60 for
®
. The maximum cable length is 60 feet.
R E S I D E N T I A L S T E A M G E N E R AT O R S S P E C I F I C A T I O N C H A R T
Model No. KW 240v/1PH)† Size‡ Room Vol. Gallons†† Dimensions* Wt. (lbs)**
MS90E 5 21 10 100 0.67 14½"L x 14¾"H x 6¾"D 30
MS150E 6 25 8 150 0.80 14½"L x 14¾"H x 6¾"D 30
MS225E 7.5 32 8 225 1.0 14½"L x 14¾"H x 6¾"D 30
MS400E 9 38 8 360 1.2 14½"L x 14¾"H x 6¾"D 30
MS SUPER 1E 10 42 8 475 1.4 17"L x 18½"H x 77⁄8"D 40
MS SUPER 2E 12 50 6 575 1.6 17"L x 18½"H x 77⁄8"D 40
MS SUPER 3E 15 63 4 675 2.0 17"L x 18½"H x 7
MS SUPER 4E 20 84 8 875 2.7 17"L x 18½"H x 77⁄8"D x 2 80
MS SUPER 5E 24 100 6 1075 3.2 17"L x 18½"H x 77⁄8"D x 2 80
MS SUPER 6E 30 125 4 1275 4.0 17"L x 18½"H x 7
IMPORTANT NOTES:
• Add C1 suffix to Model No. for 240V/1Ph; Add B1 suffix to Model No. for 208V/1Ph.
• Models SUPER 1E-6E must use iTempo/Plus
• All MrSteam MS Models are cULus Listed and CE approved.
NOTES:
All MS Generators available in 240v/1PH, 208v/1PH and other voltages/phases.
† Amps are for 240/1PH rated units.
‡Wire size (AWG) based on minimum 90˚C rated THHN copper conductors.
Refer to the National Electrical Code for other types of conductors.
See MrSteam® Installation and Operation Manual for complete dimensional and installation information.
MS SUPER 4E includes two MS SUPER 1E steam generators, and require one iTempo/Plus
steam generators, and require one iTempo/Plus
iTempo/Plus
®
Control, and two matching steamheads.
®
control.
®
Control, and two matching steamheads. MS SUPER 6E includes two MS SUPER 3E steam generators, and require one
Amps (for Wire Total Adj. Water Usage Shipping
®
Control, and two matching steamheads. MS SUPER 5E includes two MS SUPER 2E
2
7
⁄8"D 40
7
⁄8"D x 2 80
*Dimensions are for generator only, without
AutoFlush® or plumbing features.
**Shipping weight and pricing are for generator only,
without control or steamhead.
†† Water usage based on 20 minutes of operation.
Page 5
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
BEFORE INSTALLING
Carefully inspect the Steam Generator and packaging for
shipping damage. In the event of shipping damage, please
contact the carrier for claim information. Our
customer service department can assist you with any
missing or damaged parts.
Read these instructions before installation or service.
Although this MS steambath generator has been fully qualified for shipment by MrSteam
reviewed for proper, safe and enjoyable steam bathing:
1. Verify that the model and accessories specifications are
correct for the incoming line voltage.
2. Insure steambath generator has been correctly sized for
the steambath room. Pay particular attention to room vol-
®
, the following must be
STEAM ROOM GUIDELINES
1. Steam room must be completely enclosed, with full
walls, door, floor and ceiling.
2. It is recommended that a gasketed door is used for
steam containment.
WARNING
3. To prevent slip and fall hazards non-skip
!
strips must be installed on the steam room floor.
4. Check the suitability of any materials with the
manufacturer. Walls and ceilings must be constructed
of water-resistant, non-corrosive surface, such as tile,
marble, molded acrylic, or other non-porous material.
5. The ceiling should be sloped to prevent dripping of
condensate.
6. Provide a floor drain.
7. No heating, venting or air conditioning devices
should be installed inside the steam room.
8. Steam room tile construction information is available
from the Tile Council of America, Inc. by purchasing
the TCA Handbook for Ceramic Tile Installation.
Tel. (864) 646-8453 or www.tileusa.com.
9. Windows that are part of the steam room should be
double paned and tempered safety glass.
10. Limit steam room ceiling height to 8 feet. Exceeding
8 feet may require a higher-rated steam generator.
ume and construction. If any questions, please refer to
MrSteam sizing and selection guide on page 2.
3. Marble or glass walls or ceilings. “ENLARGE” the room’s
size, requiring a generator larger than one based only
on the room’s cubic foot (L x H x W) volume.
4. The physical size of the unit, clearance for plumbing
servicing, and its distance from the steam room must all
be considered before final installation.
5. Consider any controls and accessories before initiating
installation. Read the Installation and Operation Manual
of all controls and accessories available at
www.mrsteam.com technical downloads.
6. Record the serial number of the steam generator in the
space provided in the table of contents of this manual.
WARNING
!
manual provided with the steam bath generator is an essential
part of providing a safe environment for steam room users. The
peel and stick warning label must be applied to the wall of the
shower or steam enclosure, at a point that is visible to all users.
Failure to install this sticker may result in serious injury or death.
The location where this owner's manual is kept shall be written
in the space provided on the label using permanent ink. For a
replacement warning label contact MrSteam customer service
at 1-800-76-STEAM or hello@mrsteam.com
The peel and stick warning label located in the
Not Actual Size
I N S T A L L E R
WARNING
!
result in an inoperative or hazardous installation.
• Discontinue use of the steam generator and control if the steam
generator or control are damaged or otherwise not functioning
properly. Doing so may result in an inoperative or hazardous
installation
• ELECTRICAL SHOCK HAZARD. MrSteam steam generators are
connected to 240V line voltage and contain live electrical
components. All installation and service to be performed by
qualified and licensed electricians and plumbers only. Installation
or service by unqualified persons or failure to use MrSteam parts
may result in property damage or in a hazardous condition.
• The MS series of steam generators are for residential use only.
Commercial or other nonresidential applications void the warranty and may adversely affect product performance and may represent a safety hazard.
Never use damaged equipment, doing so may
CAUTION
!
materials are used as part of the steam room enclosure. Consult with
the material manufacture and see pg. 7, “Installing the Steamhead"
for additional details.
IMPORTANT NOTES:
This document contains important safety, operation and maintenance
information. Leave this document with the homeowner. Do not
discard this document.
The following general information should be used in conjunction
with consultations with an architect, designer and contractor in
determining factors necessary in providing a suitable and safe steam
room.MrSteam steam generators are intended to be operated with
MrSteam iSteam
and iGenie®controls only, and are to be installed strictly in accordance with the specific instructions contained in this manual and as
supplied in the manuals provided with the controls or accessories.
3
If acrylic, fiberglass or other non-heat resistant
®
, AirTempo®, iTempo/Plus®, iTempo®Home Wizard
®
Page 6
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
WATER QUALITY INFORMATION
I N S T A L L E R
For optimum results, the water supply should be tested prior
o installation. If the mineral content exceeds the following
t
recommended limits, various external treatment processes are
recommended to correct the problem.
NOTE: An analysis of the on-site water must be made by a
recognized and reliable water treatment company to ascertain
the existing condition and treatment required.
Poor water quality can affect efficiency or result in steam generator
damage. Water contains impurities in solution and suspension.
These impurities concentrate in the generator. The concentration of
these impurities increases as more feedwater is introduced into the
generator and steam is produced. If the suspended solids are
allowed to concentrate beyond certain limits, a deposit or “scale”
will form on the generator internal surfaces. This deposit can
interfere with the proper generator operation and cause generator
failure. The concentration of these impurities is generally controlled
by the water quality and by periodic draining of the generator.
RECOMMENDED FEEDWATER QUALITY
Hardness, ppm 8 – 85 (~0.5 – 5 gpg)
P-Alkalinity, ppm 85 – 410 (~5 – 24 gpg)
T. Alkalinity, ppm 200 – 500 (~7 – 0 gpg)
pH (strength of alkalinity) 8.0 – 11.4
Every 2 months, or more often in “hard” water
areas, the manual drain valve should be opened
fully flushing out accumulated materials, salts and
other particles which are natural by-products of
boiling water.
The optional AutoFlush System feature automatically drains the MrSteam generator following each use.
A time delay allows the water to cool down (about
two hours) before it drains by gravity for a safe and
gentle operation.
LOCATING THE STEAM GENERATOR
Select a location as near as practical to the steam room. Typical locations include: closet, vanity cabinet,
heated attic or basement.
NOTE:
control must be located accordingly. A 60 foot cable is available as a special order part for iTempo
PN 103990-60 and PN 104117-60 for iSteam
IMPORTANT NOTE: The control cable should be run in a dedicated 1" conduit to facilitate installation and service.
together with power lines or close to hot water or steam piping. Doing so may result in an inoperative or hazardous installation.
The standard length of the cable for connecting the control to the steam generator is 30 feet. The steam generator and
®
.
The maximum cable length is 60 feet.
WARNING
!
DO NOT route iSteam, AirTempo, iTempo/Plus, iTempo, HomeWizard or iGenie control wiring inside conduit
®
and AirTempo®,
WARNINGS
!
1. DO NOT
a shock hazard will occur.
2. DO NOT
wherever environmental conditions may result in a
shock hazard or affect performance of the generator.
3. To prevent damage to the steam generator or a fire
hazard DO NOT
flammable or corrosive materials or chemicals such as
gasoline, paint thinners, or the like. Installation in areas
having high concentrations of chlorine (such as pool
equipment room) must be avoided.
4. Burn Hazard. Steam line, safety valve, drain valve and
plumbing become hot during operation and remain
hot after shutdown for a period of time. Provide
appropriate protection, including insulating plumbing
lines. Avoid plumbing runs and steamhead locations
that can come in contact with bathers.
5. Suitable for operation in ambient not exceeding 45 °C
(113˚ F). Operation of the steam generator in an ambient
temperature above 45 *C (113 *F) may result in a
hazardous condition or property damage
CAUTIONS
!
DO NOT
6.
unheated attic or any locations where water could freeze
and cause pipes to rupture and cause property damage.
(Items 1-5)
install steambath generator inside steam room,
install steambath generator outdoors or
install steambath generator near
(Items 6-8)
install steambath generator or plumbing lines, in
7. Install steambath generator on a solid and level surface.
Keyhole slots are provided for wall mounting. Insure the
steam generator is properly secured and level when
mounting with keyhole slots to prevent damage to the
steam generator.
8. Install steambath generator in an upright position only
to prevent damage to the generator.
IMPORTANT NOTES: (Items 9-13)
9. Install anti-water hammer device as necessary.
10.Provide a minimum of (12) inches at both ends and top of
the steam generator or as required for servicing. See page 8.
11.
Provide unions as required to facilitate installation
and disconnection of piping.
12
. MrSteam controls can be located inside the steam room
or on the outside of the steam room. See the Control
Installation Manual for your specific control package for
specific details.
13. The MS series of steam generators are for residential use
only. Commercial or other nonresidential applications
void the warranty and may adversely affect product
performance and may represent a safety hazard.
NOTE:
MrSteam Generators (inclusive of the iTempo, AirTempo
and iSteam series controls) are CE and UL listed.
4
Page 7
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
TYPICAL MRSTEAM INSTALLATION
NOTE: Drawings for illustrative purposes only.
Consult with qualified designer, architect or
contractor for steam room construction details.
Provide unions as required to facilitate
installation and disconnect of piping
Field installed
power supply
Steam
Generator
Drain Valve must be closed
when the optional
AutoFlush is not installed
When installing the optional AromaSteam, install a downward facing 90-degree T in the steam supply line. See the
AromaSteam Installation Manual for complete information.
Field installed
water supply line
Field installed
steam supply pipe
CAUTION
!
temperature sensor. Locate the control in a location
representative of the desired steambathing temperatures. Do not locate the control above or near the
steam head or direct steam emissions.
Steam Head (shown with optional acrylic shield)
See page 7 for Steam Head Installation information
CAUTION
!
where other controls, accessories, shower heads, valves, body sprays or similar within the
shower could cause confusion or interfere with the MrSteam control’s intended use and function.
The control features an integral
Control cable run in
1” conduit (located
behind the wall)
To avoid unintentional steambath operation, do not locate the control
iSteam®, AirTempo
or iTempo®Control
Refer to Control
Installation Manual
for installation
information
®
I N S T A L L E R
TYPICAL INSTALLATION INSTRUCTIONS
FOR MODELS MS SUPER 4E, 5E & 6E
1. Install each steam generator as in a single installation. Install generators as close as practical to each other, not exceeding 10 feet.
The interconnecting cable length is 12 feet.
WARNING
2. Shock Hazard. Power must be disconnect-
!
ed at the main electrical supply. Remove steam generator covers. Retain screws and covers for reuse.
3. Connect the iSteam
®
or AirTempo®control to either
unit as per the Installation Manual supplied with
each control.
4. Remove one knock-out on each generator as shown.
Insert the ends of interconnecting cable provided
(PN 103904) through the knock-outs as shown in
diagram. Connect each end to the printed circuit
board connector labeled "TANDEM" as shown.
5. Prevent the interconnecting cable from contacting
hot surfaces such as steam outlet, safety valve
and the like.
6. Connect separate plumbing and power supplies
for each unit. Replace covers with cover screws.
7.
Provide unions as required to facilitate installation
and disconnection of piping
NOTE: The secondary unit will de-energize when the
steam room reaches steambathing temperature resulting
in a more gentle and energy efficient operation.
(shown with optional AutoFlush)
Power
Supply
Secondary Unit
5
Printed Circuit Board Component
shown enlarged for illustrative purpose.
iSteam or
AirTempo
Primary Unit
Interconnecting
Cable
Control
PN 103904
Optional AutoFlush
Installation page 14
Water Feed
Line
®
, see AutoFlush
All drawings are for illustrative purposes only
Control
Cable
Steam Heads
shown with
optional acrylic
shields
Page 8
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
INSTALLATION
I N S T A L L E R
PLUMBING
All plumbing shall be performed by a qualified licensed plumber
and in accordance with applicable National and local codes.
1. Use unions on all pipe connections.
2. Use only brass piping or rigid copper tubing as permitted
by codes.
3. DO NOT use black, galvanized, PVC pipe or PEX except as
noted below.
WATER SUPPLY (3⁄8" NPT)
1. Connect to cold water line.
NOTE: Water feed line may be flexible copper tubing, braided
hose, PVC or PEX if permissible by local codes.
2. Provide a shut off valve in the water supply line upstream of
the steambath generator.
3. DO NOT overheat inlet solenoid valve with solder connections.
Overheating will damage parts.
4. Flush inlet water line thoroughly before making connection
to unit.
5. Strainer recommended upstream of feed water connection.
6. In order to reduce operating noise, reducing feed water pres-
sure to between 15 - 20 psi is recommended. Optional pressure reducing valve part number 104198.
7. Provide anti-water hammer device as required.
8. Install an approved backflow preventer as required
by local codes.
DRAIN (1⁄2" NPT)
CAUTION
!
undersink trap, unless the generator is mounted higher than the
sink to prevent damage to the generator if the drain backs up.
NOTE: A drain valve is provided to facilitate servicing. Provide a
drain line connection from steambath generator drain valve
according to National and local Codes. Check local plumbing
code for receptor, trap and vent requirements. Do not connect
Drain line and Safety Valve line together. Unit drains by gravity.
NOTE: Do not plumb the generator drain and drip pan drain
together in such a way that will cause drain water to back into
drip pan.
WARNING
!
location where accidental contact with drain water may occur. In
the event of a power failure the AutoFlush System valve will
open and may discharge boiling water causing a scalding hazard.
DO NOT connect the drain valve to the steam line
The drain from the generator should not share an
DO NOT drain into a steam enclosure or any
STEAM OUTLET (1⁄2" NPT)
1. DO NOT install any valve in steam line. Flow of steam must
be unobstructed.
2. Use 1/2-inch brass pipe or copper tubing from unit to steam
head as permitted by codes.
3. Insulate steam line with fiberglass pipe insulation or similar
insulation rated 212° F or higher.
4. Pitch steam line 1/4" per foot towards steam head or steam
generator to avoid valleys and trapping of condensate.
NOTE: Running the steam line down and then up will create a
steam trap blocking the flow of steam.
NOTE: A 1.5" hole in the steam room is required to mount the
steamhead.
SAFETY VALVE (3⁄4" NPT)
Where permitted by local codes, provide an outlet plumbing
connection for safety valve.
WARNING
!
operation: DO NOT connect a shut off valve or a plug at safety
valve outlet. DO NOT connect a shut off valve or any obstruction in steam supply pipe. DO NOT connect the safety-valve
output into the steam line.
To insure proper and automatic safety valve
DRIP PAN
MrSteam strongly recommends the use of a drip pan in the
unlikely event of a plumbing leak. Check local plumbing codes
for receptor, trap and vent requirements. Drip pans drain by
gravity. The drip pan is equipped with an integral3/4" fitting.
See page 15 for additional drip pan installation information.
NOTE: Do not plumb the generator drain and drip pan drain
together in such a way that will cause drain water to back into
drip pan.
AROMASTEAM
If the optional AromaSteam Electronic Oil Delivery System
PN:MS AROMA
(
fitting must be installed at a designated location on the steam
outlet line. See the MrSteam AromaSteam Operation and
Instruction Manual (
before the steam line is installed at the technical downloads
section of www.mrsteam.com
) is to be installed, a 90 degree T plumbing
PN
: 100402) for installation information
6
Page 9
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
INSTALLING THE ROUND OR SQUARE
AROMASTEAM STEAMHEAD
NOTE: A 1
needed to mount the steamhead.
STEP 1
Locate steam head 6-12 inches above floor, except for:
1. Tub/shower enclosures, install 6 inches above tub top edge.
2. For enclosures with acrylic or other non-heat resistant
flooring install Acrylic Shield Part Number MS-103938.
3.To prevent door seals from deteriorating do not locate
the steam head where direct steam emission would contact
door seals.
STEP 2
Install steamhead with the oil well facing up as shown. Hand
tightening is sufficient when teflon or equal pipe thread sealing
compound is used.
STEP 3
Secure a bronze drop ear fitting to a header and run a
copper steam line from the steam generator to the drop ear
fitting. Install a temporary nipple (6" or longer) in the drop ear
fitting to locate the steamhead after the wall is finished.
STEP 4
After the wall has been finished, mark on the nipple where the
surface of the wall is. Remove the nipple and measure the
portion that was in the wall (the end to your mark). Subtract
from that dimension and select a brass nipple of that length to
finish the installation.
1
⁄
" clearance hole around the steam pipe is
2
(1⁄2" NPT)
1
⁄
"
2
1
⁄4"
Use Teflon®or
equal sealant on
pipe threads
Apply with silicone or equal
sealant as required for
moisture seal.
Oil Well
Steam
Supply Pipe
STEP 3
1/8" minimum clearance required
when Acrylic Shield is used.
See installation instructions provided
with the Acrylic Shield.
End of pipe to be recessed
1/4"
(without Acrylic Shield)
1/8" (with Acrylic Shield)
Drop Ear
Fitting
I N S T A L L E R
STEP 5
Wrap teflon tape around the threads of the new nipple and screw
the nipple into the steamhead. Do not use wrenches or tools which
would damage the steamhead's finish.Wrap teflon tape around the
threads of the nipple and screw the nipple and steamhead assembly you just made into the drop ear fitting in the wall. The steamhead should be flush with the wall and the well must be facing up.
__________________________________________________________
IMPORTANT NOTE: DO NOT disassemble steamhead.
MrSteam’s steamhead is shipped fully assembled and requires
no additional assembly.
To preserve steam head finish, DO NOT use wrench or other
tools to tighten. DO NOT use abrasive cleansers or chemicals.
Use only water with mild soap and a non-abrasive sponge.
CAUTION
!
Because the steam head and direct steam
emissions are very hot, locate the steam head where incidental
contact by bather with the steam head or direct steam emission
cannot occur.
Consult with supplier of acrylic, fiberglass and other non-heat
resistant enclosures for recommended steamhead location.
Use Acrylic Shield PN MS-103938 (round) or PN MS-103938SQ
(square). See instructions provided with steam shield.
STEP 4
STEP 5
Steamhead
(shown with
optional acrylic shield
)
Locating Nipple
All drawings are for illustrative purposes only
7
Page 10
””
for servicing
D
I N S T A L L E R
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
GENERATOR DIAGRAM
Water Inlet
Control &
Accessory
Connections
team Outlet
S
Safety Valve
Optional AutoFlush
Manual Drain Valve
J
IMPORTANT NOTES:
Provide a minimum of (12) inches at both ends and top of
the steam generator or as required for servicing. Alternately,
provide unions as required to facilitate installation and disconnection of the steam generator.
The minimum clearance from combustible surfaces is zero
all around.
Side View Showing
Element Access Panel
TO AVOID EQUIPMENT
DAMAGE DO NOT
CONNECT POWER
SUPPLY DIRECTLY TO
ELEMENTS !!!
All drawings are for illustrative purposes only
MS 90E- MS 400E MS Super 1E-3E
_______________________________________
3
⁄8” NPT
1
⁄2” NPT
3
⁄4” NPT
1
⁄2” NPT
1
⁄2” NPT
1
⁄4 (184)
1
⁄4 (57)
7
⁄8 (124)
A
5 (127) 7
1
B
8
⁄8 (206) 97⁄8 (251)
1
C
11
⁄4 (392) 151⁄2 (394)
1
D
14
⁄4 (392) 183⁄4 (476)
7
E
1
⁄8 (48) 11⁄4 (32)
F
2 (51) 2
7
G
5
⁄8 (149) 6 (152)
H
5 (127) 4
7
I
6
⁄8 (175) 77⁄8 (200)
J
2 (51) 2 (51)
1
K
14
⁄2 (368) 17 (432)
1
L
2
⁄2 (64) 21⁄2 (64)
3
M
6
⁄8 (162) 63⁄8 (162)
NOTES
:
1. M= Optional AutoFlush
2. All units in inches (MM)
3. MS Super 4E includes (2) MS Super 1E units
4. MS Super 5E includes (2) MS Super 2E units
5. MS Super 6E includes (2) MS Super 3E units
WATER INLET
STEAM OUTLET
SAFETY VALVE
MANUAL DRAIN VALVE
AUTOFLUSH VALVE
8
Page 11
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Water Feed
Liquid
Level Probe
AutoFlush
®
Plug and
Play Connection
(see page 14)
Fuses
Contactor
Power Block
Power Supply
Knock-Out
Steam
Outlet
Field
Wiring
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Steam Outlet
Liquid
Level Probe
AutoFlush
®
Plug and
Play Connection
(see page 14)
Contactor
Power Supply
Knock-Out
Field
Wiring
Water Feed
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
EL E CT R IC A L C HA R T
ol Max Room Wire Size Wire Size
V
KW
Volts†Phase Amps
208 1 24 10 8
240 1 21 10 10
3 12 12 12
208 1 29 88
240 1 25 88
3 14 12 12
208 1 36 88
240 1 32 88
3 18 10 10
208 1 44 8 6
240 1 38 88
3 22 10 10
208 1 49 66
3 24 88
208 1 58 64
3 29 88
208 1 73 43
3 36 88
AWG)for 40˚ C (AWG) for 45˚ C
(
Ambient Ambient
ELECTRICAL
WARNING
!
a qualified licensed electrician in accordance with
National Electrical Code and local electrical code.
POWER WIRING
See “Field Power Wiring” Diagrams (below)
1. Check power voltage. Use 240V rated unit when supply
is greater than 208V. (Most homes have 240V, 1PH
service). Use 208V rated unit for 208V power.
2. Use minimum 90˚ C/300V rated insulated copper
conductors only, sized in accordance with National
Electrical Code and local electrical code for the current
in Ampere Chart. If allowed by codes, NM cable may
require a larger wire size than as listed on the chart.
3. Connect suitably sized equipment grounding wire to
ground terminal provided.
4. Install a separate circuit breaker between supply and
unit. Provide a power supply disconnect within sight
of the steam generator or one that is capable of being
locked in the open position.
5.
For single phase units, use two-wire supply source and
equipment grounding wire. Neutral (white) wire is not
required.
WARNING
!
All electrical wiring to be installed by
PROVIDE A POWER SUPPLY DISCONNECT WITHIN SIGHT OF THE STEAM GENERATOR OR ONE
THAT IS CAPABLE OF BEING LOCKED IN THE OPEN POSITION AS REQUIRED BY CODE.
________________________________________________________________________________________________________
Model No.
________________________________________________________________________________________________________
MS-90E 100 5.0 3 14 12 12
_______________________________________________________________________________________________________
_
MS-150E 150 6.0 3 17 10 10
________________________________________________________________________________________________________
MS-225E 225 7.5 3 21 10 10
________________________________________________________________________________________________________
MS-400E 360 9.0 3 25 88
_______________________________________________________________________________________________________
_
MS-Super 475 10.0 3 28 88
________________________________________________________________________________________________________
MS-Super 575 12.0 3 34 88
_______________________________________________________________________________________________________
_
MS-Super 675 15.0 3 42 86
________________________________________________________________________________________________________
*See page 2 for room sizing.
†
All specifications shown are for 208V and 240V Consult factory for other voltage specifications.
(Cu. Ft.*)
1E 240 1 42 86
2E 240 1 50 66
3E 240 1 63 44
I N S T A L L E R
FIELD POWER WIRING
1. TO AVOID EQUIPMENT DAMAGE
DO NOT CONNECT POWER SUPPLY
DIRECTLY TO ELEMENTS!!!
2. L1, L2, Ground to be field wired
3. Super 1E 240/1 models
are not supplied with internal fusing.
4. All Drawings are for illustrative
purposes only. Consult with qualified
licensed electrician for electrical
installation.
Models MS 90E–MS 400E
(single phase wiring shown)
Models MS Super 1E-6E
(single phase wiring shown)
9
Page 12
FAC TOR Y
WIR ING
FIE LD
WIR ING
L E G EN D
(All Diagrams)
C
ONTACTOR
HEATING ELEMENT
TO PROBE
CONTROL BOARD
AutoFlush
S
teamGenie or
iGenie
(optional)
iSteam, AirTempo
i
Tempo/Plus or
i
Tempo Control
T
RANSFORMER
P
OWER INPUT
GROUND
WATER
FEED
S
OLENOID
VALVE
CONTACTOR
HEATING ELEMENT
TO PROBE
CONTROL BOARD
AutoFlush
SteamGenie or
iGenie
(optional)
iSteam, AirTempo
iTempo/Plus or
iTempo Control
TRANSFORMER
P
OWER INPUT
GROUND
W
ATER
F
EED
SOLENOID
VALVE
F
USES
POWER INPUT
TRANSFORMER
CONTROL BOARD
CONTACTOR
GROUND
HEATING ELEMENT
TO PROBE
WATER
FEED
SOLENOID
VALVE
AutoFlush
(optional)
SteamGenie or
iGenie (optional)
iSteam, AirTempo
iTempo/Plus or
iTempo Control
I N S T A L L E R
mr.steam
Installation, Operation & Maintenance Manual
__________________________________________________________________________
SINGLE PHASE 208/240 VOLT WIRING DIAGRAMS
MODELS MS90E, MS150E,
MS225E, MS400E
®
MODELS MS SUPER-1E,
MS SUPER-2E,
MS SUPER-3E
(Note: Super 1E 240V
does not have fuses)
THREE PHASE 208/240 VOLT WIRING DIAGRAM
MODELS MS90E, MS150E,
MS225E, MS400E,
MS SUPER-1E,
MS SUPER-2E,
MS SUPER-3E
10
Page 13
AutoFlush
(optional)
iTempo/Start
(optional)
iSteam, AirTempo
or iTempo/Plus
AutoFlush
(optional)
Do Not
Connect
Control
FAC TO RY
WIR IN G
FIE LD
WIR IN G
L E G EN D
(All Diagrams)
{
C
ONTACTOR
PRIMARY UNIT SECONDARY UNIT
AutoFlush
(optional)
Steam Genie
(optional)
iSteam, AirTempo
or iTempo/Plus
AutoFlush
(optional)
PLUG THIS END
TO MASTER UNIT
PRIMARY UNIT
SECOND UNIT
TO THIRD UNIT
TO FOURTH UNIT
TO FIFTH UNIT
Optional Tandem Cable for 2-5 Generators
Length is 30 ft. PN: 103917
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
INSTALLATION INSTRUCTIONS
FOR MODELS: MS-SUPER 4E, MS-SUPER 5E AND MS-SUPER 6E
1.
Install each unit as in a single installation. Install the two generators as close to each other as possible.
2.
WARNING
!
steam generator covers.
3. Connect the iSteam
4. Remove one knock-out on each generator as shown. Insert the ends of interconnecting cable provided (PN 103904)
through the knock-outs as shown in the Diagram on page 5. Connect each end to the printed circuit board as shown.
5. Connect separate plumbing and power supplies for each unit.
Wiring Diagram: MS-Super 4E, MS-Super 5E, MS-Super 6E
Shock Hazard.
®
, AirTempo®or iTempo/Plus®control to either generator per the control instructions..
Power must be disconnected at the main electrical supply before removing
I N S T A L L E R
OPTIONAL TANDEM CABLE
For connecting more than 2 steam generators in tandem
11
Page 14
I N S T A L L E R
1
2
4
7
8
9
3
6
5
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Ste
Ou
Liquid
Level Probe
AutoFlush
and Play
Connectio
Contactor
Power Supply
Knock-Out
Field Wiring
Water Feed
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
INITIAL START-UP AND CHECKOUT
1. Turn on control. Follow specific instructions provided with controls.
2. Steam will begin to appear in approximately 5 minutes (unless equipped
with factory-installed Express Steam option) at the steam head. Steam
will shut off when desired temperature is reached and will automatically
resume when room temperature drops below set point.
3. Steam will shut off automatically when control counts down to zero.
To shut steam off manually, turn control OFF. To clear steam from
enclosure area, turn shower on before opening door.
4. If unit does not start and control does not turn ON (control display does
not light up) then turn breaker off for 20 seconds and try again.
5. Check all internal and external plumbing fittings for leaks while the
steam is on.
OPTIONAL & ACCESSORY EQUIPMENT
Refer to specific instruction manual for installation, operation and maintenance of optional equipment and
accessories such as iSteam
®
, AirTempo®, iTempo/Plus®, iTempo®, Home Wizard®, iGenie®and MSTS.
TROUBLESHOOTING
IMPORTANT NOTE: The model and serial number is printed on
the data plate on the front of the steam bath generator.
Step 1 Check main incoming power to the unit.
Step 2 Ensure the black wires from the pri-
mary side of the transformer are connected
to the quick connect tabs on the line side
of the contactor.
Step 3 Verify that you have 24VAC
coming out of the transformer, WHT &
WHT/BLU wires, into the board.
Step 4 Verify that you have the green
light on the PC board.
Step 5 Push the white test button to
run the generator for 10 minute test
cycle. Make sure the steam room is
empty.
Step 6 Verify that you have 24 VAC to the water feed
solenoid, GRY & WHT/GRY wires (will fill when needed).
Step 7 Temporarily short out the WLS (Purple wire) and GND (Green wire) terminals and verify the contactor engages.
Step 8 When the red light is on, verify 24 VAC,
RED & WHT/RED wires, to the contactor.
WARNING
!
All electrical troubleshooting to be performed by a qualified licensed electrician
Step 9 Check main voltage on the
load side of the contactor when it is engaged.
Step 10 If all steps on the power path were verified, turn off power to the unit
and pull the heating element via the left hand access panel for inspection.
DO NOT disassemble internal components,
internal components contain no serviceable parts.
12
All drawings are for illustrative purposes only
Page 15
mr.steam
R
ED
(
H
eater)
Y
ELL
OW
(
Water Lev
el)
GR
EEN
(
Po
wer
)
Force On
Test Button
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
SYSTEM STATUS CODES
The control (either iSteam®, AirTempo®, iTempo®or iTempo/Plus®) may display a status code if the steam generator is not functioning
properly.
Code Code Meaning Probable Cause Suggested Remedy
H20 Water level is not Water Supply is off Turn on Water Supply
satisfied within 5 min.
Prr1 Temperature Probe Error Control cable/MSTS cable cut Replace control cable/MSTS
or Prr2
Err1 Incorrect Field Supply Voltage Incorrect voltage supplied Supply steam generator with the correct
(green light on liquid level to Generator voltage noted on the data plate label.
control board will be off)
Err2 Button on control is pressed Control cover misalignment Remove and reinstall control cover
for more than 5 minutes
Defective water feed solenoid Check/replace water solenoid valve
Water feed probe not functioning Check/clean probe.
Check probe wiring.
Drain Valve Open Check/Close drain valve
AutoFlush not functioning Check/Replace AutoFlush
Internal problem with control/MSTS Replace control / MSTS
Debris behind control cover Remove control cover and clean cover,
control and keypad with a damp cloth
I N S T A L L E R
Errb Water level not satisfied in a tandem set up - Check secondary generators, see H20.
Err7 Liquid Level Control Board malfunction Memory error in LLCB Press ON/OFF to clear.
Replace control if code remains.
LIQUID LEVEL CONTROL BOARD Explanation of LED Indicators
______________________________________________________________________________________________________________________________________
GREEN LED is ON when there is 208/240 Volt incoming power connected,
______________________________________________________________________________________________________________________________________
YELLOW Water level indicator–LED is OFF when no water is detected (for more that 5 seconds). ON when
______________________________________________________________________________________________________________________________________
RED Contactor relay indicator–LED is ON when relay is closed and sending 24 Volts to the
______________________________________________________________________________________________________________________________________
FORCE ON Press this button to operate the generator. This button is for trouble shooting only and will operate
TEST BUTTON
Liquid Level Control Board
PN 103975
(shown without wiring)
24 Volt transformer secondary output and on-board 5 Volt DC control power are present.
water level is satisfactory. For units with AutoFlush, if more than five hours have elapsed since
last usage and this LED is ON it is indicative of an AutoFlush or water level probe circuit malfunction.
contactor coil. (This LED comes ON if the generator is ON.)
if a control is connected or not. Pressing the button again will shut the generator OFF. The test button
will only allow the generator to operate for 10 minutes.
All drawings are for illustrative purposes only
13
Page 16
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
OPTIONAL AUTOFLUSH
®
Box Contents
AutoFlush Valve with Cord
Installation Instructions.
OPERATION
The optional AutoFlush System feature automatically drains
the MrSteam generator following each use. A time delay
allows the water to cool down (about two hours) before it
I N S T A L L E R
drains by gravity for a safe and gentle operation.
NOTE:
If the Express Steam®option has been installed, the
AutoFlush will drain for ten minutes then refill with fresh water
to begin the pre-heat cycle.
INSTALLATION INSTRUCTIONS
1. Plumbing to be performed by a qualified plumber and shall be in
accordance with applicable national and local codes. Unit drains
by gravity. A drain line that is lower than the AutoFlush
must be available. The AutoFlush System valve outlet is
Check plumbing code for receptor, trap and vent requirements.
2. Use copper or brass nipple
to connect AutoFlush valve (end "B") to the Drain Valve (valve end
“A” and “B” are indicated on bottom of AutoFlush Valve)
1
⁄2“ NPT x 31⁄2“ or longer (not supplied)
®
assembly
1
⁄2“ NPT.
Steam Generator
Drain Valve
shown in the correct
(
open position)
O NOT REMOVE
D
HIS DRAIN VALVE
T
3 Pin Connector
for AutoFlush
AutoFlush Cord
Connector
AutoFlush Cord
ipplecopper or brass
N
1
nipple
⁄2" NPT x 31⁄2" or
not supplied)
(
onger
l
End
"B"
Arrow indicates correct direction of flow
E
"A"
nd
AutoFlush
Valve
lumb to
P
Drain Line
CAUTION
!
DO NOT REMOVE THE DRAIN VALVE
Removal may cause equipment and property damage. If there is
not enough room for the valve, an elbow and a short nipple
(not provided) can be added.
3. Open Drain Valve (handle must be aligned with brass nipple).
4. Connect the AutoFlush System cord connector to the three pin
connector as shown.
WARNING
!
DO NOT drain into a steam enclosure or any location
where accidental contact with drain water may occur. In the event of
a power failure the AutoFlush System valve will open and may discharge boiling water causing a scalding hazard.
SWEAT FITTINGS
When using sweat fittings use only tin base solder with a melting
point below 600 degrees F. DO NOT overheat. Ends of water supply
tubing must be thoroughly clean for a minimum distance of 1" from
ends. DO NOT remove valve cover.
TO CHECK OPERATION
1. Turn on MrSteam and allow tank to fill with water.
2. Turn off MrSteam control. Water should stay in tank.
3. Turn off power at the panel box. Water should
discharge from tank.
4. Turn on power at panel box.
5. Repeat
Steam Generator
Drain Valve
DO NOT TURN OR REMOVE
THE DRAIN VALVE
(shown in the correct open
position)
AutoFlush Shown Fully Assembled
AutoFlush
Valve
Nipple
Plumb to
Drain Line
CAUTION
!
PROVIDE DRAIN PLUMBING ACCORDING TO LOCAL
CODES. PLUMB AS REQUIRED FOR AUTOFLUSH SYSTEM.
All drawings are for illustrative purposes only
14
Page 17
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
OPTIONAL DRIP PAN
MrSteam strongly recommends the use of a drip pan
n the unlikely event of a plumbing leak.
i
Locate the drip pan on a solid level surface and
place the steam generator inside the drip pan.
Insure the steam generator is level (see page 4 for
locating the steam generator).
All plumbing shall be performed by a qualified
licensed plumber and in accordance with applicable
national and local codes. Check local plumbing
code for receptor, trap and vent requirements.
Drip pans drain by gravity.
The drip pan is equipped with an integral female
3
⁄4" NPT fitting.
NOTE: Do not plumb the generator drain and drip
pan drain together in such a way that will cause drain
water to back into drip pan.
I N S T A L L E R
OPTIONAL EXPRESS STEAM
(only available factory installed)
Available for all MS Models. Express Steam generators are equipped with a low power heating element
and thermostat to keep the water in the tank warm
enough to bring up steam quicker. All Express Steam
components and wiring are installed at the factory.
No additional wiring or plumbing is required by
installers.
®
All drawings are for illustrative purposes only
15
Page 18
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Water Inlet
Safety Valve
AutoFlush
Valve
(optional)
Stainless Steel Tank
Heating Element
Express Steam
heater (optional)
Element
Access Cover
Liquid Level Probe
Plug and Play
Connection
(see page 13)
Power Block
Power Supply
Knock-Out
Contactor
Steam Outlet
Fuses
Nipple
(not included)
Manual
Drain Valve
Transformer
D
rain Line
Nipple
(not included)
L
iquid Level
C
ontrol Board
W
ater Feed
S
olenoid
Water Inlet
S
afety Valve
AutoFlush
Valve
(optional)
Stainless Steel Tank
H
eating Element
Access Cover
Liquid Level Probe
P
lug and Play
C
onnection (see page 13)
C
ontactor
Power Supply
Knock-Out
S
team Outlet
Express Steam
H
eater (optional)
Manual
D
rain Valve
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
PARTS IDENTIFICATION DIAGRAMS
MS REGULAR MODELS
MS65E - MS400E
(with AutoFlush®)
shown with cover removed
I N S T A L L E R
NOTE:
FOR ILLUSTRATIVE PURPOSES ONLY.
Some components may be omitted or
altered for clarity. DO NOT use for wiring,
repair or other purposes not related to
component identification.
MS SUPER MODELS - MS SUPER 1E- MS SUPER 6E
(with AutoFlush®)
shown with cover removed
NOTE: Super 1E 240/1
models are not supplied
with internal fusing.
NOTE:
FOR ILLUSTRATIVE PURPOSES ONLY.
Some components may be omitted or
altered for clarity. DO NOT use for wiring,
repair or other purposes not related to
component identification.
16
Page 19
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
REPLACEMENT PARTS LIST
_________________________________________________________________________________________________
Part No. Description Generator
_________________________________________________________________________________________________
99178MS Drain Valve All Models
99297 Safety Valve 15PSI All Models
100479 Water Feed Solenoid Valve w/filter All Models
10477-3 Transformer 24VAC All Models
103975 Liquid Level Control Board All Models
103904 Tandem Cable for 2 generators (12 ft.) All Models
103917 Tandem Cable for up to 5 generators (30 ft.) All Models
103990-60 Cable for iTempo®Control (60 ft.) All Models
104117-30 Cable for iSteam®, AirTempo®and iTempo (30 ft.) All Models
104117-60 Cable for iSteam (60 ft) All models
MSTS Remote Temperature Probe All Models
for iTempo/Plus and AirTempo
iMSTS Remote Temperature probe for iSteam All Models
100476-2 Contactor 50A 2-pole MS 90E-400E, Single phase
99012 Contactor 50A 3-pole All 3-Phase Models
103453 Contactor 50A 4-pole MS Super-1E – Super-6E
100471-2 Probe Assembly All Models
99096MS Heating Element Gasket All Models
103938 Round Acrylic Shield iTempo & iTempo/Plus All Models
103938 Square Acrylic Shield iTempo & iTempo/Plus All Models
99314 Power Fuse 60A 250V MS-Super 1E–6E Single phase
29051BMS Heating Element 5 KW 208V MS 90E
29051CMS Heating Element 5 KW 240V MS 90E
29061BMS Heating Element 6 KW 208V MS 150E
29061CMS Heating Element 6 KW 240V MS 150E
29071BMS Heating Element 7.5 KW 208V MS 225E
29071CMS Heating Element 7.5 KW 240V MS 225E
29091BMS Heating Element 9 KW 208V MS 400E
29091CMS Heating Element 9 KW 240V MS 400E
29101BMS Heating Element 10 KW 208V MS SUPER-1E & MS Super-4E
29101CMS Heating Element 10 KW 240V MS SUPER-1E & MS Super-4E
29121BMS Heating Element 12 KW 208V MS SUPER-2E & MS Super-5E
29121CMS Heating Element 12 KW 240V MS SUPER-2E & MS Super-5E
29151BMS Heating Element 15 KW 208V MS SUPER-3E & MS Super-6E
29151CMS Heating Element 15 KW 240V MS SUPER-3E & MS Super-6E
104058 iGenie All Models
104059 iGenie Interface Module All Models
104060 iGenie Interface Cable (5 ft.) All Models
I N S T A L L E R
17
Page 20
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
CONTROL INSTALLATION
Refer to Control Manual for specific installation requirements
BEFORE INSTALLING
Turn power to the steam generator OFF before connecting the
control to the generator. Failure to turn the power off will result in
an inoperable control.
CAUTION
!
DO NOT locate the control where other controls, acces-
I N S T A L L E R
sories, shower heads, valves, body sprays or similar within
the shower could cause confusion or interfere with the
MrSteam control’s intended use and function.
CAUTION
!
iTempo/Plus
without reading and understanding its own manual and the
MrSteam steam generator Installation and Operation Manual.
Failure to read and understand these instructions may result
in an inoperative or hazardous installation.
WARNING
!
and permanently affixed in a conspicuous location near the
steam room. Failure to read and affix this warning sticker in a
conspicuous location may result in serious injury or death. .
Install the iSteam, AirTempo, iTempo or iTempo/Plus controls
according to installation instructions. Failure to install according to instructions will result in an inoperative control or hazardous overheating or inadequate heating of the steam room.
If an iSteam, AirTempo, iTempo or iTempo/Plus control is
installed outside the steam room a Remote Temperature
Probe (PN MSTS or iMSTS) must be installed inside the
steam room per installation instructions supplied with the
Remote Temperature Probe. Failure to install according to
instructions will result in an inoperative control and overheating of the steam room.
o avoid unintentional steambath operation,
T
DO NOT use any iSteam
®
, iTempo®, HomeWizard®or iGenie®controls
A peel and stick warning sticker must be read
®
, AirTempo®,
WARNING
!
iTempo, HomeWizard or iGenie control wiring inside conduit
together with power lines or close to hot water or steam piping.
Doing so may result in an inoperative or hazardous installation.
DO NOT alter or modify any MrSteam product. Doing so may
result in an inoperative or hazardous installation and will void the
UL listing and warranty.
IMPORTANT NOTES:
1. Turn power to the steam generator OFF before connecting the control to the generator. Failure to turn the power
off will result in an inoperable control.
2. DO NOT operate iSteam, AirTempo,iTempo/Plus, iTempo,
HomeWizard or iGenie controls with other than a MrSteam
iSteam, AirTempo, or iTempo compatible steam generator.
MrSteam residential steam generators with serial numbers
lower than 900000, or any other brand of steam generator
are not to be operated with iTempo controls. Doing so
may result in an inoperative or hazardous installation. If
iSteam is used with a generator having serial number
900000 through 930030, contact MrSteam technical support for an upgraded PC board.
3. This document contains important safety, operation and
maintenance information. Leave this document with the
homeowner. Do not discard this document.
4. Discontinue use of the steam generator or control if the
steam generator is damaged or otherwise not functioning
properly. Operating a damaged steam generator may
result in an inoperative or hazardous installation
DO NOT route iSteam,
AirTempo,
iTempo/Plus,
CONTROL ROUGH IN
Refer to Installation Instructions for the specific control
IMPORTANT NOTE: The control cable should be run in a
dedicated 1” conduit to facilitate installation and service.
1.
Determine the desired installation location of the control. The iSteam
controls are designed to be installed inside or outside the
steam room as a matter of personal preference. If the control is in-stalled inside the steam room the control must be
located:
2. 4-5 feet above the floor near the bather seating area
3. The control features an integral temperature sensor.
Locate the control in a location representative of the
desired steambathing temperatures.DO NOT locate
the control above or near the steam head or direct
steam emissions.
4. on a vertical wall
The iSteam and iTempo control cable length is 30 feet.
Insure that the control and/or steam generator are located accordingly. An optional 60 foot cable is available, PN
®
,
AirTempo®,
iTempo®and iTempo/Plus
103990-60 for AirTempo and iTempo and PN 104117-60 for
iSteam. Contact a MrSteam technical service representative if
a 60 foot cable is required. Excess control cable should be
neatly coiled and twisted into a figure 8. The AirTempo dongle
®
is provided with a 3 foot cable. The maximum cable length is
60 feet.
IMPORTANT NOTES:
• If the control is installed outside the steam room a Remote
Temperature Probe Part Number MSTS or iMSTS must be
installed inside the steam room, depending on the control.
• Insure MrSteam steam generator is iSteam, AirTempo or
iTempo compatible and has a serial number 900000 or higher. If iSteam is used with a generator having serial number
900000 through 930030, contact MrSteam technical support
for an upgraded PC board.
•
See instructions for the MSTS or iMSTS Temperature Probe
(located in the Control Installation Manual related to your specific control package) before rough-in or installation of control.
18
Page 21
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
H O M E O W N E R S E C T I O N
RE A D M E FI R ST !
WARNING
!
instructions, you will notice warning
and caution symbols. This blocked
information is important for the safe
and efficient installation and operation
of this generator. These are types of
potential hazards that may occur during
installation and operation:
WARNING
!
hazardous situation, which, if not avoided, could result in death or serious
injury.
CAUTION
!
hazardous situation, which, if not avoided may result in minor or moderate
injury or product damage.
IMPORTANT NOTE:
highlights information that is especially
relevant to a problem-free installation.
All information in these instructions is
based on the latest product information
available at the time of publication.
Sussman-Automatic Corporation
reserves the right to make changes at
any time without notice.
As you follow these
Indicates a potentially
Indicates a potentially
This
When using this steam bath equipment, basic safety precautions should always
be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
WARNING
2.
!
WARNING
3.
!
injury or death if improperly used. Steam
rooms contain steam and elevated temperatures. Please read and observe all warnings
in this manual before installing or using a
steam room.
WARNING
4.
!
A. The wet surfaces of steam enclosures
may be slippery. Use care when entering
or leaving.
B. The steam head is hot. DO NOT touch the
steam head and avoid the steam near
the steam head.
C. Prolonged use of the steam system can raise
excessively the internal human body temperature and impair the body’s ability to regulate
its internal temperature (hyperthermia). Limit
your use of steam to 10-15 minutes until you
are certain of your body’s reaction.
D. Excessive temperatures have a high potential
Supervise children at all times..
Steam is hot and can cause
To reduce the risk of injury:
for causing fetal damage during the
early months of pregnancy. Pregnancy
or possibly pregnant women should
consult a physician regarding correct
exposure.
E. Obese persons and persons with a his-
tory of heart disease, low or high
blood pressure, circulatory system
problems, or diabetes should consult
a physician before using a steambath.
F. Persons using medication should con-
sult a physician before using a steambath since some medication may
induce drowsiness while other medications may affect heart rate, blood
pressure and circulation.
SAVE THESE
INSTRUCTIONS
HYPERTHERMIA
nal temperature of the body reaches a
level several degrees above the normal
body temperature of 98.6° F. The symptoms of hyperthermia include an increase
in the internal temperature of the body,
dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit
the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath
and
f) Unconsciousness
WARNING
!
drugs, or medication can greatly increase
the risk of hyperthermia.
occurs when the inter-
.
The use of alcohol,
WARNING
!
stick warning label located in
the manual provided with the
steam bath generator is an
essential part of providing a
safe environment for steam
room users. The peel and stick
warning label must be applied
to the wall of the shower or
steam enclosure, at a point that
is visible to all users. Failure to
install this sticker may result in
serious injury or death.
The location where this owner's
manual is kept shall be written
in the space provided on the
label using permanent ink.
For a replacement warning label
contact MrSteam customer service
at 1-800-76-STEAM or hello@mrsteam.com
The peel and
19
Not Actual Size
Page 22
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
H O M E O W N E R
SETTING THE STEAM BATH
TEMPERATURE AND DURATION
WARNING
!
ing to personal preference, however it is highly recommended to begin steam bathing at a low temperature set-
ing to gauge comfort and safety levels. Set duration to a
t
maximum of 10 minutes to gauge comfort and safety levels. This will allow the steam generator to heat up and
begin producing steam.
Set the steam bathing temperature accord-
SAFETY AND OPERATING
INFORMATION
WARNING
!
AirTempo
®
iGenie
MrSteam steam generator Installation and Operation
Manual. Failure to read and understand these instructions
may result in an inoperative or hazardous installation.
WARNING
!
the manual provided with the steam bath generator must
be read and permanently affixed in a conspicuous location
near the steam room. Failure to read and affix this warning
sticker in a conspicuous location may result in serious injury
or death.
If an iSteam, AirTempo, iTempo or iTempo/Plus control is
installed outside the steam room a Remote Temperature
Probe (PN MSTS or iMSTS) must be installed inside the
steam room per installation instructions supplied with the
Remote Temperature Probe. Failure to install according to
instructions will result in an inoperative control and
overheating of the steam room.
WARNING
!
strips must be installed on the steam room floor.
DO NOT install or use any iSteam®,
®
, iTempo/Plus®, iTempo®, HomeWizard®or
controls without reading and understanding the
The peel and stick warning label located in
To prevent slip and fall hazards non-skip
CARE TIPS FOR ALL CONTROLS AND
STEAMHEADS
1. Use only mild soap and water on a soft cloth to clean
the control and steamhead.
2. DO NOT use abrasive cleansers.
3. If the decorative cover is damaged on the iTempo
r iTempo/Plus call MrSteam technical service for
o
replacement parts.
NOTE: Replacement of the decorative covers requires
removal and reinstallation of the control from the mounting
surfaces.
STEAM GENERATOR MAINTENANCE
MrSteam steambath generators require little maintenance.
Other than periodic draining, maintenance procedures are minimal. Every 2 months, or more often in “hard” water areas, the
manual drain valve should be opened fully flushing out accumulated materials, salts and other particles which are natural byproducts of boiling water.
CAUTION
!
trol has been turned off to insure that the water has cooled.
WARNING
!
expose PVC and other piping to high temperature water. Check
local codes. The unit will refill automatically when the control is
activated again. In areas of hard water, a MrSteam AutoFlush
system is recommended for generator longevity.
WARNING
!
equipment and user to scalding water and cause property and
personal injury.
IMPORTANT NOTE: The model and serial number is printed on
the data plate on the front of the steam bath generator.
Flush a minimum of two-three hours after the con-
Draining immediately after a steam cycle may
®
Failure to allow the water to cool will expose the
WARNING
!
product. Doing so may result in an inoperative or
hazardous installation and will void the UL listing and
warranty.
IMPORTANT NOTES:
lightning, fire, freezing or flooding is not covered under
the warranty.
Discontinue use of the steam generator or control if the
steam generator is damaged or otherwise not functioning
properly. Doing so may result in an inoperative or
hazardous condition.
DO NOT alter or modify any MrSteam
Malfunction due to power spikes,
20
Page 23
mr.steam
®
Installation, Operation & Maintenance Manual
__________________________________________________________________________
USING MRSTEAM®ESSENTIAL OILS
Enjoy AromaSteam essential oils by placing a drop or two
into an unheated AromaSteam steamhead as shown in the
illustration. Only use MrSteam AromaSteam essential oils in
he MrSteam AromaSteam steamhead.
t
AromaSteam
10ml bottle
with integrated
dropper
WARNING
!
cause inflammation, burns, headache, nausea and allergic
reactions. Consult a physician before using aroma therapy.
CAUTIONS
!
1. Use essential oils with caution. Essential oils are for external use only. Keep out of reach of children. Essential oils
are highly concentrated and are potent substances and
should not be applied directly to the skin as they can be
irritants. Use essential oils with caution.
Place the drops into the MrSteam AromaSteam steamhead
2.
recess prior to turning on the steambath. DO NOT place
drops in a hot steam head as serous injury can result if you
do not follow this warning.
3. Start with one drop to gauge strength and suitability. Limit
to a maximum of a few drops for a steambathing session.
4. The bather should exit the steambath IMMEDIATELY if
dizziness occurs. If skin irritation occurs stop using the oils
immediately. Remove any excess oil by washing in mild
soap and water. If ingested, rinse mouth with water.
Administer water or milk to dilute. Contact a physician
immediately.
CAUTION
!
turning on the steambath unit. DO NOT add oil
before
during steambathing or when the steam head is heated.
Essential oils and/or aroma therapy can
Aromatic oils should be added to steamhead
Recess for
essential oil
Steam
emission
slot
AromaSteam steamhead
(install per instructions on pg.7)
H O M E O W N E R
Tightly close bottles when storing oils.
Keep bottles away from sources of ignition.
All drawings are for illustrative purposes only
WARRANTY
To view or download the MrSteam Residential Generator Warranty
and register your Product go to:
blog.mrsteam.com/wr
21
Page 24
®
mr
steam
.
®
Feel Good Inc.
www.mrsteam.com
Products, information and specifications are subject to change without notice.
Please call Sales & Support at 1.800.76.STEAM (East Coast) or 1.800.72.STEAM (West Coast) for more information.
mr.steam
43-20 34th Street, Long Island City, NY 11101
TEL: 1 800 76 STEAM FAX: 718 472 3256
2018 © Sussman-Automatic Corporation I MrSteam and des., A Lifetime of Pleasure, AirTempo, AromaFlo, AudioWizard, AutoFlush, AutoSteam, Butler Package, ChromaSteam, Clean Steam...Every Time,
Club Therapy, CT Day Spa, Digital 1, Express Steam, Feel Good Inc., From Bathroom to Spa, HomeWizard, iButler, iGenie, iSpa Package, iSteam, iTempo, iTempo/Plus, Linear Steamhead, Making Wellness
a Way of Life, Music Therapy, My Steam, SmartSizing, Spa Package, Steam Genie, Steam on Demand, Steam in a Box, Steam@Home, SteamStart, SteamTherapy, Sussman, Tala, Tala Bath & Body, Tempo,
The Intelligent Steambath, Valet Package, and Virtual Spa System are registered trademarks of Sussman-Automatic Corporation.
®
Sussman-Automatic Corporation
®
hello@mrsteam.comIwww.mrsteam.com
I
9410 S. La Cienega Blvd. Inglewood CA 90301
TEL: 1 800 72 STEAM FAX: 310 216 2944
PUR 100472A 8.18
Loading...