mr. steam eTempo Plus Operation And Installation Instructions Manual

mr.steam®aromasteam

Operation and Installation Instructions

_________________________________________________

MS AromaFlo®A

Table of Contents

Box Contents

Assembly and Installation

General Installation
Installation of Hoses

Assembly Diagram . . . . . . . . . . . . . . . . . . 5

Electrical Wiring

Sta

rt-up

Initial Priming of AromaSteam System
Filling the Pressure Hose

Adjusting amount of oil delivery

Troubleshooting

Technical Information

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . . . .

. . .

. . . . . . . . . .

. . . . 7

. . . . . . . . . . . . . .

. . . . . . . . . .

2

3
4

6

7
7

8

8

WARNING

!

fragrance or fragrance containing emulsifiers or aldehy­des. AromaSteam system damage may result. Mr.Steam
oils are approved for operation with this system.

WARNING

!

Mr.Steam oils may introduce excessive concentration of
oil into the steam room, resulting in a health hazard.

WARNING

!

dizziness. Keep out of the reach of children. In case of
contact with eyes, rinse immediately with plenty of
water and seek medical advice. If swallowed, rinse mouth
with water (only if the person is conscious), seek medical
advice immediately and show this container or label.

WARNING

!

from sources of ignition– No smoking. Keep container
tightly closed & in a well-ventilated place. This material
& its container must be disposed of as hazardous waste.

WARNING

!

rooms.

Material Safety Data Sheet (MSDS) available upon request

IMPORTANT NOTE:

As you follow these instructions, you will notice warning and caution symbols.This blocked information is important for the safe and efficient
installation and operation of this AromaSteam. These are two types of potential hazards that may occur during this installation and operation:

Do not use with water soluble

The use of any oils other than

Vapors may cause drowsiness and

Highly Flammable. Keep away

Not for use in acrylic or fiberglass

NOTE:

It is strongly recommended that this warning sign (supplied)

be posted in a conspicuous location near the steam room.

This room is equipped with an aromatic oil dispensing system.

Leave the room immediately if you have any adverse or
allergic reactions, including difficulty breathing or eye, nasal,
throat, or skin irritation and seek medical attention.

mr.steam

1 800 76 STEAM www.mrsteam.com

AromaSteam

(for illustrative purposes only)

!

WARNING

®

43-20 34th Street , Long Island City NY 11101

PUR 100405

WARNING

!

states a hazard which may cause serious injury
or death if precautions are not followed.

mr.steam

Sussman-Automatic Corp
[e-mail]
www.mrsteam.com

®

43-20 34th Street

®

Long Island City, NY 11101
Tel: 1-800-76 STEAM
Fax: [phone]

CAUTION

!

signals a situation where minor injury or product
damage may occur if you do not follow instructions.

9410 S. La Cienega Blvd.
Inglewood CA 90301
1-800 -72 STEAM
Fax: [phone]

IMPORTANT NOTE:

This highlights information that is especially relevant
to a problem-free installation.

PUR 100402 - 6/08

Motor Operated

Pumps24VW

mr.steam®aromasteam Operation and Installation Instructions

TABLE OF CONTENTS

Box Contents . . . . . . . . . . . . . . . . . 2

Assembly and Installation

General

.. . . . . . . . . . . . . . . . . . . . 3

Pump Assembly

.. . . . . . . . . . . . . . . . 4

Installation of Hoses

.. . . . . . . . . . . . . . 4

System Schematic

.. . . . . . . . . . . . . . . 5

Electrical Wiring

.. . . . . . . . . . . . . . . . 6

Assembly Diagram

.. . . . . . . . . . . . . . . 7

Start-up

Initial Priming of Metering Pump

.. . . . . . 8

Filling the Pressure Hose

.. . . . . . . . . . . 8

Programming Table

.. . . . . . . . . . . . . . 9

Maintenance

M

aintenance of Metering Pump,

Suction Valve, and Pressure Valve

.. . . . . . 10

Troubleshooting.. . . . . . . . . . . . . . 11

Technical Information . . . . . . . . . . 11

SpareParts . . . . . . . . . . . . . . . . . . 11

Warranty.. . . . . . . . . . . . . . . . . . . 12

ADivision of Sussman-Automatic Corporation

43-20 34th Street, Long Island City, NY 11101 • [phone] • 1-800-767-8326 • Fax:[phone] • www.mrsteam.com

Western Regional Offices

9410 S.La Cienega Blvd., Inglewood CA 90301 • 1-800 72 STEAM (1-800 727-8326) • Fax:[phone]

P

UR 100402 - 01/06

NOTE:

Sussman-Automatic strongly recommends that this warning sign

(supplied) be posted in a conspicuous location near the steam room.

Donot use with water soluble fragrance or fragrance containing
e

mulsifiers or aldehydes.AromaStean pump damage may result.

MrSteam oils are approved for operation with this pump.

The use of any oils other than MrSteam oils may introduce excessive
concentration of oil into the steam room, resulting in a health hazard.

WARNING

!

WARNING

!

s

ignals a situation where minor injury or product

dam-age may occur if you do not follow instructions.

IMPORTANT NOTE:

THIS HIGHLIGHTS INFORMATION THAT IS ESPECIALLY
RELEVANT TO A PROBLEM-FREE INSTALLATION.

IMPORT

ANT NOTE:

Asyou follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and operation of
t

his AromaSteam.These are two types of potential hazards that may occur during this installation and operation:

s

tates a hazard which may cause serious injury
or death if precautions are not followed.

Fragrance Metering Pump
for Residential Steam Rooms

This room is equipped with an aromatic oil dispensing system.

Leave the room immediately if you have any adverse or
allergic reactions, including difficulty breathing or eye, nasal,
throat, or skin irritation and seek medical attention.

MrSteam

®

C

ommercial Steam Generators
Sussman-Automatic Corp.43-20 34th Street , Long Island City NY 11101
1800 76 STEAM • www.mrsteam.com

WARNING

!

L

isted Oil Delivery

P

ump

24

V

W

mr.steamaromasteam

®

operation and installation instructions

_________________________________________________

WARNING

!

CAUTION

!

______________________________________________________________________________________________

Box Contents

Shipping Hose

AromaSteam System 6 ft. Pressure Hose 2 ft. Suction Hose with Filter
& Bracket Assembly
(with integrated 6 ft. power cord,
8 ft. request cable and 3 ft. demand cable)

1/2 inch NPT Atomizing Nozzle Injector with Injection Hose Scent Container Cap

Demand Button

(with integral 30 ft. cable)

Installation & Operation Manual

with Peel-off Warning Label

2

mr.steam®aromasteam Operation and Installation Instructions

______________________________________________________________________________________________

General Installation

CAUTION

!

For use with residential steam rooms only. Not for commercial use.

Locate the AromaSteam system to monitor the consumption of essential oils and for easy oil replacement.

1.

2.

Mr.Steam strongly suggests that the warning sticker provided be placed in a conspicuous location near the
steam room.

3.

Mr.Steam AromaSteam System is designed and intended for indoor use only and is to be located indoors in a dry
clean location and not subject to moisture, condensation or similar high humidity environments.

4.

Do not install AromaSteam Systems outdoors.

5.

Do not install AromaSteam Systems in a location where water could freeze.

6.

Do not install AromaSteam Systems near flammable or corrosive materials and chemi­cals. Installation in areas having high concentrations of chlorine (such as pool equip­ment room) should be avoided.

7.

Attach the AromaSteam System onto a secure vertical surface.

8.

Provide access to AromaSteam System for servicing, and refills.

9.

The system should not be installed in areas accessible to children. A LOCKED ROOM
IS STRONGLY RECOMMENDED (ie: utility room)

10.

Height difference between AromaSteam System discharge and 90 degree

held to a maximum

The AromaSteam system is qualified for use with Mr.Steam residential steam generators ONLY.

!

WAR NI NG

This room is equipped with an aromatic oil dispensing system.

T is to be

6 ft. (see page 5).

Leave the room immediately if you have any adverse or
allergic reactions, including difficulty breathing or eye, nasal,
throat, or skin irritation and seek medical attention.

mr.steam

1 800 76 STEAM www.mrsteam.com

®

43-20 34th Street , Long Island City NY 11101

PUR 100405

Clearance to heat sources

•

Do not install the AromaSteam system directly below or above the Mr. Steam steam

generator where it is subject to heat.

•

Minimum distance between the AromaSteam system and a heat source (e.g. steam

generator, heating system) is 1.5 ft. If this minimum distance of 1.5 ft cannot be
maintained, install a radiation plate or heat insulation between the heat source and
AromaSteam system.

•

Ambient temperature at and around the AromaSteam system should not exceed 90˚ F.

Installing the 90 degree T and Atomizing Nozzle

1.

For optimal results locate a brass 90 degreeT(not provided) and atomizing nozzle
in the steam supply line between 16" and 36" from the steam head (see page 5). If
using copper tubing for steam lines, install a female 1/2 NPT thread to sweat fitting
in the downward facing

must face downward as shown (in figure 2).

2. T

3.

Screw the atomizing nozzle into 90°Tfitting using teflon tape on the threads.

Note:

The further the 90°Tis from the steam head (more than 36”) the more the fra­grance degrades and be less effective. Conversely, the closer the 90°Tis to the steam­head (less than 16”) the less the fragrance will "blend" with the steam and the aroma
effect will be lessen.

T.

90˚ T

Steam Line

1/2 NPT

Figure 2

IMPORTANT NOTE:

Follow the installation instructions for the steam
pipeline in the Mr.Steam Residential Steam Bath Installation and Operating
Manual (PUR 101289). Visit www.mrsteam.com to download this document.

3

mr.steam®aromasteam Operation and Installation Instructions

______________________________________________________________________________________________

Installation of Pressure Hose to AromaSteam System.

1.

Unscrew the pressure end nut from the pump head and remove the shipping hose

and the pressure end nut.

2.

Insert the pressure hose through the hole of the pressure end nut and firmly push

the pressure hose onto the pressure valve.

3.

Screw the pressure end nut onto the pressure valve and tighten the nut by HAND only.

Installation of Suction Hose in Scent Container

1.

Locate the “container cap” in the AromaSteam box.

2.

Unscrew the cap from the Mr.Steam scent container and discard.

Open End

Container Cap

Suction Hose

Filter

Container Height 8 inches

3.

Insert the suction hose with the open end from below through the hole in the

container cap (see Fig. 3).

4.

Insert the filter into the scent container so that the filter rests on the bottom.

5.

Screw the cap onto the scent container.

Installation of Suction Hose to AromaSteam System

1.

Unscrew the suction end nut from the pump head and remove shipping hose
(see Fig. 3) (discard shipping hose, keep pressure end nut).

2.

Remove suction end nut from the shipping hose.

3.

Insert the open end of the suction hose through the hole of the suction end nut.

4.

Firmly push the hose onto the cone of the suction valve at the pump head.

5.

Screw the suction end nut to the suction valve.

IMPORTANT NOTE:

HAND-TIGHTEN ONLY.

Figure 3

Suction Suction Pump Pressure Pressure

End Nut Valve Head Valve End Nut

Figure 4

4

mr.steam®aromasteam Operation and Installation Instructions

______________________________________________________________________________________________

Typical AromaSteam Installation

For use with
eTempo/Plus®Controls

Locate the AromaSteam system to
monitor the consumption of essential
oils and for easy oil replacement.

NOTE:

CABLES SHOULD NOT CONTACT STEAM PIPE.

FOR ILLUSTRATIVE PURPOSES ONLY

ypical Mr.Steam

T

team Generator

S

Cable to Steam Generator

(Request Cable)

Scent Container

AromaSteam

Demand Button

Pump Line Cord 120V

(grounded receptacle required)

Atomizer Nozzle

Pressure Hose

Suction Hose

Mounting
Bracket

Steam Line

90˚ T

Mi

Ma

x

. d

Max ht.6 ft.

AromaSteam
System

UTILITY

ROOM

eTempo/Plus

n

. d

i

s

t

a

n

c

e

i

s

16

t

a

n

"

c

e

36"

Steam Head

STEAM ROOM

For use with Tempo
Tempo/Plus

®

and

eTempo®Controlss

®

,

Cable to Steam Generator

Typical Mr.Steam
Steam Generator

(Request Cable)

Scent Container

Atomizer Nozzle

Pressure Hose

Suction Hose

Mounting
Bracket

Steam Line

90˚ T

Mi

Ma

x

. d

Max ht.6 ft.

AromaSteam
System

AromaSteam
Demand Button

n

. d

i

st

a

n

ce

i

st

16

a

n

"

ce

36"

Steam Head

STEAM ROOM

Tempo,
Tempo/Plus
& eTempo

UTILITY

Pump Line Cord 120V

(grounded receptacle required)

ROOM

5

mr.steam®aromasteam Operation and Installation Instructions

Contactor

Contactor

______________________________________________________________________________________________

Electrical Connection of AromaSteam™System

CAUTION

!

This AromaSteam system is factory
wired. If the power cord of the AromaSteam system is
damaged it must be replaced by the Sussman-Automatic
service department or similarly qualified personnel in
order to avoid risks. All electrical connections to be made
by a licensed, qualified electrician. Disconnect all power
to the steam generator before making power connec­tions.

1.

Disconnect all power to the Mr Steam steambath gen-

erator and remove the top cover.

2. Run the request cable from the AromaSteam System

through one of the knockouts in the side of the
steambath generator. Use a strain relief bushing or
grommet to prevent chafing.

3. Locate the contactor inside the steambath generator

and identify the red and red/white wires. (NOTE:
Tempo generations use blue & white wires).

4. Remove those two wires from the contactor

and attach the request cable to those two
terminals.

5. Reconnect the red and red/white wires by attaching

them to the piggyback terminals on the request cable.

AromaSteam Wiring Schematic

AromaSteam

120 VAC

Outlet

(grounded receptacle required)

Plug

Request Cable
24 VAC

Connector Connector

Demand Cable

to steam generator
(see below)

AromaSteam Connections when using
eTempo®Controls

(refer to Installation Instructions

Demand Button

for proper location)

NOTE: When using generators hooked up in tandem the
AromaSteam steam system should be connected to the
contactor on the primary generator. The atomizing nozzle
should be connected to the main generator’s steam line.

Demand Button

ETEMPO/PLUS INSTALLATIONS:

1.

Locate the demand button on or near the pump brack­et. The demand button will be used to turn on the
AromaSteam pump only during installation (and if
power is cut to the pump) as the AromaSteam pump is
controlled by the eTempo/Plus

TEMPO, TEMPO/PLUS AND ETEMPO INSTALLATIONS:

1.

Locate the demand button in a location accessible
to the steambather. Mr.Steam suggests adjacent to
the Tempo Controls.

2. A 7/8 inch hole is required for the demand button.

3. Fill the hole with silicone as required for a mois-

ture seal, care should be taken not to get silicone
on the adhesive on the back of the button.

For Tempo, Tempo/Plus, and eTempo

Contactor location in MS-65T- MS400T
and MS90E - MS400E

For Tempo, Tempo/Plus, and eTempo

Contactor location in MSSUPER1T- MSSUPER6T
and MSSUPER1E- MSSUPER6E

6

mr.steam®aromasteam Operation and Installation Instructions

______________________________________________________________________________________________

Start-up

Initial Priming of the Pump

1. Insure MrSteam scent container is full.

2. Insert the short injector hose onto the tip of the injector

(see Fig. 5).

3. Unscrew the pressure end nut from the pump head and remove the
pressure hose from the pressure valve (see Fig.3).

4. Insert the open end of the injection hose onto the pressure valve
(see Fig. 5).

5. Draw liquid from the injector slowly and evenly. Continue until the
injector is full of liquid.

6. If you have drawn up the injector completely and no liquid is in the
injector, remove the injector hose from the pressure valve.

7. Drain injector. Repeat steps until the injector is filled.

8. Save the oil injector as it will be needed when new oils are used.

Filling the Pressure Hose

1.

Insure the AromaSteam System is primed and the scent container

is full.

2

. Locate the Push-button at the rear of the metering pump (see

Fig. 6). Depress this push-button to start metering pump.

3.

Continue to depress push-button until the pressure hose is filled
with liquid.

Figure 5

Pressure Valve

AromaSteam

Metering Pump

Injector Hose

IMPORTANT NOTE:

of the pressure hose, and after new oil bottles are installed.

Push button to be used only for initial filling

Operation

ETEMPO/PLUS

1.

Press the AROMA button on the eTempo/Plus
control (Aroma will appear in the display).

2

. When the generator is steaming the pump will inject oil into the

steam line at preset time intervals.

3

. If the generator is not steaming, no oil will be pumped.

TEMPO, TEMPO/PLUS AND ETEMPO

1.

With the generator on press the demand button once

(the demand button will light up).

2

. When the generator is steaming the pump will inject oil into the

steam line at preset time intervals.

3

. If the generator is not steaming, no oil will be pumped.

Note:

After the generator has been turned off the light on the
demand button will remain ON, the pump will be in stand-by mode
waiting for the generator to be turned on again.

Aroma button

Push Button

Figure 6

Adjusting the Amount
of Oil Delivery

WARNING

!

suitable amount of aromatic oil into a typical sized steam room. PLEASE CONTACT
THE MRSTEAM TECHNICAL SERVICE DEPARTMENT BEFORE CHANGING THIS SETTING.

Increasing the settings may introduce excessive concentration of oil into the
steam room, resulting in a health hazard.

Contact the MrSteam Technical Service Department at (800) 76-STEAM (East
coast) or (800) 72-STEAM (West coast)

WARNING

!

personnel may adjsut the factory setting.

The AromaSteam system has been factory set to deliver a

for assistance or additional information.

Only a qualified licensed electrician or factory authorized

7

mr.steam®aromasteam Operation and Installation Instructions

______________________________________________________________________________________________

Troubleshooting

WARNING

!

TO AVOID ELECTRIC SHOCK, DISCONNECT POWER TO PUMP BEFORE SERVICING

METERING PUMP DOES NOT PRIME

1.

Check if voltage is available.

2.

Check liquid level in scent container. Replenish liquid, if necessary.

3.

Check for air bubbles in the suction hose or the pump head. To eliminate air bubbles see: Priming Pump.

4.

Check valves for contamination. Clean valves, if necessary.

5.

Check filter in container for contamination. Rinse filter under clean water.

Metering pump does not inject oil into steam room

1.

Check if voltage is available.

2.

Check liquid level in scent container. Replenish liquid, if necessary.

3.

Check for air bubbles in the suction hose or the pump head. To eliminate air bubbles see: Priming Pump.

4.

Check valves for contamination. Clean valves, if necessary.

5.

Check filter in container for contamination. Rinse filter under clean water.

6.

Check the pressure hose for kinking or jamming. Straighten or replace.

7.

Check if liquid is freely flowing through the atomizing nozzle when the metering pump is energized. Apply compressed air through the atomizing

nozzle. Attach the compressed air at the point of connection of the pressure hose.

8.

For eTempo/Plus: ensure the demand button light is on. the demand button light should be pressed during installation, the light willl turn on. In

the event of a power outage the button will need to be pressed again.

Metering pump oil delivery too much or too little

Contact Mr.Steam techincal service personnel at 1-800-76 STEAM (East Coast) or 1-800-72-STEAM (West Coast).

Technical Specifications

List of Spare Parts

Description Part No.

Pump Head 103861
Pressure/Suction Hose EO1-1032

(ordered by the foot)

Eucalyptus oil, 1 liter MS OIL 1
Lavender oil, 1 liter MS OIL 2
Evergreen oil, 1 liter MS OIL 3
Energizing Mint oil, 1 liter MS OIL 4
Poho oil, 1 liter MS OIL 5
Atomizing Nozzle 103918
Oil Injector 103983
Filter 103987

Dimensions: 7” L x 6.5” W x 4.5” H
___________________________________________

Weight: 5 pounds
___________________________________________

EN 60335
UL Listed
CSA Approved

___________________________________________
Motor voltage 120 VAC, 50/60 Hz

Power consumption, total [W] 12 Watt

MR.STEAM and des., A LIFETIME OFPLEASURE, ALLEGRO, AROMAFLO, AUTOFLUSH, CLEAN STEAM...EVER TIME, MRSAUNA,STEAM ON DEMAND, STEAM@HOME,
SUSSMAN, SUSSMAN LIFESTYLE GROUP, TEMPO, TEMPO/PLUS, TEMPO/REMOTE, TEMPO/EXT, WARMATOWEL, eTEMPO, eTEMPO/PLUS, eTEMPO/REMOTE,
eTEMPO/START and STEAMTHERAPY, are registered trademarks of Sussman-Automatic Corporation. AROMASTEAM, CLUB THERAPY, CHROMASTEAM, F1 PLUS,
MUSICTHERAPY, SAUNA/ONE, MAKE WELLNESS a WAY of LIFE and FROM BATHROOM TO SPA are trademarks of Sussman-Automatic Corporation.

8