Mr Steam Butler, Butler2, ButlerX User Manual
Butler/Butler2/ButlerX
iTempo Plus Control PUR100474 06-15
AromaSteam SteamHead PUR100421 10-15
SteaLinx Mobile App PUR100518 01-18
MS / Super AutoFlush PUR100200E 10-15
MX AutoFlush PUR100532 02-19
Condensation Pan TS0012 02-19
2019-03-14
Installation, Operation & Maintenance Manual
iTEMPO™ & iTEMPOPLUS™ CONTROLS
®
mr.steam
www.mrsteam.com
Feel Good Inc.
When installing and using this electrical equipment, basic safety precau-
tions should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
WARNING
!
2. Do not permit children under
the age of 16 to use this steambath.
WARNING
3. Steam is hot and can cause injury or death if
!
improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual
before installing or using a steam room.
4. To reduce the risk of injury:
WARNING
!
A. The wet surfaces of steam enclosures may be slippery. Use
care when entering or leaving.
B. The steam head is hot. Do not touch the steamhead and avoid
the steam near the steamhead.
C. Prolonged use of the steam system can raise excessively the
internal human body temperature and impair the body’s ability to regulate its internal temperature (hyperthermia). Limit
your use of steam to 10-15 minutes until you are certain of
your body’s reaction.
D. Excessive temperatures have a high potential for causing fetal
damage during the early months of pregnancy. Pregnancy or
possibly pregnant women should consult a physician regarding
correct exposure.
E. Obese persons and persons with a history of heart disease, low or
high blood pressure, circulatory system problems,
or diabetes should consult a physician before using a steambath.
F. Persons using medication should consult a physician before using
a steambath since some medication may induce drowsiness while
other medications may affect heart rate, blood pressure and
circulation.
HYPERTHERMIA
internal temperature of the body
reaches a level several degrees above
the normal body temperature of 98.6°
F. The symptoms of hyperthermia
include an increase in the internal
temperature of the body, dizziness,
lethargy, drowsiness, and fainting.
The effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to
exit the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath; and
f) Unconsciousness.
WARNING
!
The use of alcohol, drugs, or
medication can greatly increase the
risk of hyperthermia.
occurs when the
SAVE THESE INSTRUCTIONS
2
mr.steam
______________________________________________________________
®
Installation & Operating Instructions
READ ME FIRST!
WARNING
!
As you follow these instruc-
tions, you will notice warning and caution
symbols. This blocked information is important for the safe and efficient installation
and operation of this generator. These are
types of potential hazards that may occur
during installation and operation:
WARNING
!
Indicates a potentially
hazardous situation, which, if not avoided,
could result in death or serious injury.
Indicates a potentially
CAUTION
!
hazardous situation, which, if not avoided
may result in minor or moderate injury or
product damage.
IMPORTANT NOTE: This highlights
information that is especially relevant to
a problem-free installation.
All information in these instructions is
based on the latest product information
available at the time of publication.
Sussman-Automatic Corporation reserves
the right to make changes at any time
without notice.
Table of Contents:
Important Safety Instructions .............................. 2
Before Installing .................................................. 4
Dimensional Information .................................... 5
Installations ...................................................... 6-8
Installing the Remote Temperature Probe ....9-11
iTempo Operating Instructions ...................12-13
iTempoPlus Operating Instructions ............. 14-17
Care and Maintenance ..................................... 18
Warranty ........................................................... 18
3
mr.steam
______________________________________________________________
®
Installation & Operating Instructions
BEFORE INSTALLING
Carefully inspect the control and packaging for shipping damage. In the event of shipping damage, please
contact the carrier for claim information. Our customer
service department can assist you with any missing or
damaged parts.
CAUTION
!
To avoid unintentional steambath operation, do not locate the control where other controls,
accessories, shower heads, valves, body sprays or similar within the shower could cause confusion or interfere
with the Mr.Steam
Do not use any iTempoPlus
or iGenie
the respective Installation and Operation Manual and
Mr.Steam steam generator Installation and Operation
Manual (PN 101289 Revision number 10.0/08 or higher).
Failure to read and understand these instructions may
result in an inoperative or hazardous installation.
WARNING
A peel and stick warning sticker is
!
provided in the MrSteam steam generator Installation,
Operation and Maintenance Manual. This manual is
provided with every steam generator. The warning
sticker must be read and permanently affixed in a
conspicuous location near the steam room. Failure to
read and affix this warning sticker in a conspicuous
location may result in serious injury or death. Please call
MrSteam at 800 767-8326 for a free replacement or if
you have any questions regarding the warning sticker.
Install the iTempo or iTempoPlus controls according to
installation instructions. Failure to install according to
instructions will result in an inoperative control or hazardous overheating or inadequate heating of the steam
room. If an iTempo or iTempoPlus control is installed
outside the steam room a Remote Temperature Probe
(PN MSTS) must be installed inside the steam room
®
control’s intended use and function.
™
®
controls without reading and understanding
, iTempo™, HomeWizard™
per instructions for the Remote Temperature Probe.
Failure to install according to instructions will result in
an inoperative control and overheating of the steam
room.
WARNING
Do not route iTempoPlus, iTempo,
!
Home Wizard or iGenie control wiring inside conduit
together with power lines or close to hot water or
steam piping. Doing so may result in an inoperative or
hazardous installation.
WARNING
Do not alter or modify any Mr. Steam
!
product. Doing so may result in an inoperative or hazardous installation and will void the warranty.
IMPORTANT NOTES:
• Turn power to the steam generator OFF before connecting the control to the generator. Failure to turn
the power off will result in an inoperable control.
• Do not operate iTempoPlus, iTempo, Home Wizard or iGenie controls with anything other than a
Mr.Steam iTempo compatible steam generator.
Mr.Steam residential steam generators with serial
numbers lower than 900000, or any other brand
of steam generator are not to be operated with
iTempo controls. Doing so may result in an
inoperative installation.
• This document contains important safety,
operation and maintenance information. Leave this
document with the homeowner.
Do not discard this document.
• Discontinue use of the steam generator
or control if the steam generator is damaged or otherwise not functioning properly. Doing so may result
in an inoperative or hazardous installation.
• All illustrations are for illustrative purposes only.
4
mr.steam
______________________________________________________________
®
Installation & Operating Instructions
Dimensional Information
for the Round and Square
iTempo
™
and iTempoPlus
BOX CONTENTS:
• iTempo™ or iTempoPlus™ Control
• Control Cable (30 ft.)
• Steam head
• Tube of Silicone Sealant
• Owner’s Manual
™
1
4
/
”
2
1
2
/
”
2
5”
5”
1”
3
/
”
8
1
/
”
4
3
/
4
3
”
3
/
”
4
12” long
pigtail
Drawings for Illustrative Purposes Only.
5
mr.steam
______________________________________________________________
®
Installation & Operating Instructions
Installation Instructions for Round & Square
iTempo
™
and iTempoPlus
STEP 1
Determine the desired installation location of the control.
The iTempo
installed inside or outside the steam room as a matter of personal
preference. If the control is installed outside the steam room a
Remote Temperature Probe part number MSTS must be
installed inside the steam room. If the control is installed
inside the steam room the control must be located:
• 4-5 feet above the oor near the bather seating area.
• The control features an integral temperature sensor. Locate
• On a vertical wall
• The control cable length is 30 feet. Insure that the control and/or steam
generator are located accordingly. Contact a Mr.Steam technical service
representative if a longer cable is required (60 ft. cable, PN 103990-60).
IMPORTANT NOTE: The control cable should be run in a dedicated
1” conduit to facilitate installation and service.
IMPORTANT NOTE: See installation instructions for the MSTS
Temperature Probe before rough-in or installation of control (pgs. 8-9).
STEP 2
Make a 2-5⁄8” wide by 3-7⁄8” high cutout in the desired control location.
Do not oversize or under size the cutout.
STEP 3
Route the control cable (provided with the control) from the wall cutout
to the steam generator. Connect one end of the cable to the steam
generator connector.
™
and iTempoPlus
the control in a location representative of the desired steam
bathing temperatures. Do not locate the control above or
near the steam head or direct steam emissions. Locating the
controls near the steamhead or near direct steam emissions
may result in poor steam room temperature control.
Diagram 1
Diagram 2
™
™
controls are designed to be
6
Drawings for Illustrative Purposes Only.
5
2-
⁄ 8”
DIAGRAM 1
DIAGRAM 2
7
3-
⁄ 8”
mr.steam
______________________________________________________________
NOTE:
The connector is keyed with the at facing
up. The control cable is the same at both ends.
®
Installation & Operating Instructions
IMPORTANT NOTE:
strain, staple, pinch or otherwise damage the
control cable. Route cable as required to permit
replacement. Do not route cable inside conduit
together with power lines or close to hot water or
steam piping.
STEP 4
Firmly connect the other end of the cable to the
control. Turn on power to the steam generator
and test the control to verify correct connections.
Test per the instructions on pages 10-15. With
verification of proper control function, proceed to
Step 5.
If the generator is on for more
than a few minutes steam will start coming out
of the steamhead. Insure that steam room is not
occupied.
STEP 5
Remove and discard peel-off paper to expose
adhesive liner.
CAUTION
!
Diagram 3
Diagram 4
Be careful not to
DIAGRAM 3
DIAGRAM 4
7
Drawings for Illustrative Purposes Only.
mr.steam
______________________________________________________________
®
Installation & Operating Instructions
STEP 6
Run a bead of silicone (provided) as shown
to the outer edge of the control faceplate,
following the contour of the circle or square
shape. Use silicone as required to create a
moisture seal.
NOTE: The silicone supplied by Mr. Steam
can be used to meet a variety of sealing and
gasketing. It cures to silicone rubber and
adheres to glass, wood, metal, porcelain,
ceramic tile, painted surfaces, many plastics
and rubber. Surfaces must be clean and dry.
Apply thin layer of product. Fit together and
support if necessary. Allow excess material
to cure, then trim with a sharp blade.
Sealant “skins” in 5 minutes, dries to touch
in 1 hour. Fully cures and bonds in 24 hrs.
IMPORTANT NOTE:
excessive amounts of silicone. Do not apply
silicone to any other parts of the control
including the adhesive gasket.
STEP 7
Insure the mounting surface is clean and
dry as required for good adhesion. Hold
the control with the LED display in the
12 o’clock position and press the control
against the wall u ntil the adhesive sticks
and holds firmly. Control may have to be
supported or secured until the silicone fully
cures and bonds.
Diagram 5
DIAGRAM 5
DIAGRAM 6
Do not apply
Diagram 6
8
Drawings for Illustrative Purposes Only.
Loading...