Mr. Heater BOSS-XB13 Basecamp, BOSS-XB18 Basecamp Owner's Manual
OPERATING INSTRUCTIONS AND OWNER’S MANUAL
BATTERY OPERATED SHOWER SYSTEM
Fully Portable Instant Hot Water/Shower
READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe
place for future reference. Do not allow anyone who has not read these instructions to assemble,
light, adjust or operate the shower.
Model #
XB13
XW18
Battery Operated Shower System
XB13
DANGER
• This appliance can produce carbon monoxide which has
no odor
•Using it in an enclosed space can kill you.
• Never use this appliance in an enclosed space such as a
camper , car or home
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
– An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
– WHAT TO DO IF YOU SMELL GAS
any other appliance.
appliance
• Do not try to light appliance
• Extinguish any open flame
• Shut off gas to appliance
CARBON MONOXIDE HAZARD
XW18
www.mrheater.com
•
800-251-0001
2017
WARNING:
YOUR SAFETY IS IMPORTANT, SO PLEASE READ THESE INSTRUCTIONS
BEFORE YOU OPERATE.
THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE
ASSEMBLY, OPERATION AND MAINTENANCE OF THIS PORTABLE
SHOWER.
SAFETY PRECAUTIONS ARE ESSENTIAL WHEN ANY MECHANICAL
OR PROPANE FUELED EQUIPMENT IS INVOLVED. THESE
PRECAUTIONS ARE NECESSARY WHEN USING, STORING AND
SERVICING. FOLLOWING THESE SAFETY ALERTS WILL REDUCE THE
POSSIBILITY OF PERSONAL INJURY OR PROPERTY DAMAGE.
PROPANE CYLINDERS MUST BE DISCONNECTED WHEN THE
SHOWER IS NOT BEING USED OR WHEN STORING THE SHOWER.
THE STATE OF CALIFORNIA REQUIRES THE FOLLOWING WARNINGS:
WARNING: COMBUSTION BY-PRODUCTS PRODUCED WHEN
USING THIS PRODUCT CONTAIN A CHEMICAL KNOWN TO
THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH
DEFECTS (OR OTHER REPRODUCTIVE HARM).
WARNING: THIS PRODUCT CONTAINS CHEMICALS KNOWN
TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM.
DANGER
EXPLOSION-FIRE
HAZARD
Never store propane
near high heat, open
flames, pilot lights,
direct sunlight, or other
ignition sources or
where temperatures
exceed 120° F (49°C)
Propane is heavier than
air and can accumulate
in low places it you
smell gas leave the area
immediately.
During operation this
product can be a source
of ignition. Never
use this appliance in
spaces that contain or
may contain volatile or
airborne combustibles,
or products such as
gasoline, solvents, paint
thinners, dust particles
or unknown chemicals
DANGER
HOT
BURN
•Water temperature
over 125°F(52°C) can
cause severe burns
instantly or death
from scalds.
•Children, disabled
and elderly are at
highest risk of being
scalded.
• See instruction
manual before
setting temperature
at water heater.
• Feel w ater before
bathing or
showering.
.
WARNING:
• NOT FOR HOME OR RECREATIONAL VEHICLE USE.
• THE WATER HEATER IS FOR POINT OF USE, FOR
TEMPORARY WATER HEATING AND NOT FOR
CONNECTION TO A PERMANENT INLET WATER
CONNECTION OR FOR CONNECTION TO A WATER
DISTRIBUTION SYSTEM TO SUPPLY MULTIPLE OUTLETS.
• DO NOT OPERATE HEATER WHERE FLAMMABLE
LIQUIDS OR VAPORS MAY BE PRESENT.
• USE THE PRESET REGULATOR THAT IS INSTALLED.
DO NOT ATTEMPT TO ADJUST.
• NEVER INSTALL OR REMOVE PROPANE TANK
WHILE HEATER IS OPERATING, NEAR FLAME,
OTHER IGNITION SOURCES OR WHILE HEATER IS
HOT TO THE TOUCH
PORTABLE HOT WATER/SHOWER:
• THIS APPLIANCE IS NOT INTENDED FOR THE SUPPLY
OF DRINKING WATER. HEALTH RISKS CAN OCCUR IF
WATER IS CONSUMED INTERNALLY
• THIS APPLIANCE IS INTENDED FOR THE SUPPLY OF
HEATED WATER FOR THE PURPOSE OF WASHING AND
CLEANING ONLY.
• CHECK AND CONFIRM SAFE WATER TEMPERATURE
BEFORE USING THIS APPLIANCE. WATER FROM THIS
APPLIANCE MAY BE VERY HOT.
Basecamp, Inc. | Portable Shower Operating Instructions and Owner’s Manual
CONTENTS
WARNINGS ................................................................................. 2
SHOWER SPECIFICATIONS ........................................................... 3
OPERATING PRECAUTIONS .......................................................... 3
SAFETY PRECAUTIONS ................................................................ 3
OPERATING INSTRUCTIONS ........................................................ 4
MAINTENANCE, STORAGE AND SERVICE ................................... 6
WIRING DIAGRAM ......................................................................7
TROUBLESHOOTING....................................................................7
EXPLODED VIEW ......................................................................... 8
PARTS LIST .................................................................................. 9
WARRANTY ...............................................................................10
INSTRUCTIONS FOR ORDERING PARTS .......................................10
LANGUAGES
ENGLISH ...........................................................................1-10
SPANISH ................................................................................1-10
FRENCH .................................................................................1-10
Clearance to Combustibles:
Model: TOP & FRONT Sides Rear
XB13
XW18
2
48” 12 ” 12 ”
48” 12 ” 12 ”
SPECIFICATIONS
CAUTION: Certified for use only with Liquid Propane
LP-gas cylinders of the U.S. Department of Transportation (DOT) or Transport Canada, CAN/CSA B339.
Model: XB13
(F235300)
Rating: BTU 10,000 -13,000 10,000 -17,000
Battery 6(D cell batteries)
Not included
Run Time (Full Charge) 30 minutes 40 minutes
Fuel Source Propane Propane
Fuel Supply Pressure
(to regulator):
Gas Supply Pressure
(Regulator out):
Electrical Input
High Temperature Control: 125°(F) 125°(F)
Temperature Rise 35°(F) 42°(F)
Ignition Piezo Spark Piezo Spark
Max. Bottle
Pressure
11” WC 11” WC
XW18
(F235325)
2.6A/HR Sealed
Lead Acid Internal
Battery
Max. Bottle
Pressure
115V, 60 Hz, 1Ø, 2A
Min. Operating
Voltage:100V
230 Watts (W)
Model XB13
Model XW18
DIMENSIONS
Model: Length(in) Width(in) Height(in) Weight(LBS)
XB13 12 1/2” 7 1/2” 12 ” 14 lbs.
XW18 19 1/4”
(Faucet to Handle)
7 1/2” 12 ” 15 lbs.
UNPACKING and ASSEMBLING
1. Remove heater from carton.
2. Remove all protective material which may have been applied
to the heater for shipment.
3. Check the appliance for possible shipping damage and
straighten out all hoses to remove any kinks or twists. If any
damage is found immediately contact the manufacturer at
1-800-251-0001.
4. Install handle assembly by screwing them into place.
5. Attach the supplied regulator by rotating the t-wing nut in a
“clockwise” direction carefully not to over tighten.
6. Attach the LP cylinder to the regulator by rotating in a
“clockwise” direction. Only use LP cylinders with proper fuel
type approved for the appliance must be used. Check for gas
leaks with soapy water.
DO NOT USE A FLAME TO CHECK FOR LEAKS.
Fuse (Model XW18)
Regulator
Assembly
Handle Assembly
Basecamp, Inc.| Portable Shower Operating Instructions and Owner’s Manual
Pump Inlet Connection
3
OPERATING PRECAUTIONS
Propane is heavier than air. If propane leaks from a connection or
fitting, it sinks to the floor, collecting there with the surrounding
air, forming a potentially explosive mixture. During set up check
all connections and fittings for leaks using soapy water. Never use
flame. Bubbles indicate a leak. Check that the connection is not
cross threaded and that it is tight. Perform another leak check.
If there is still a leak, remove the cylinder and contact Basecamp
direct for service or repair.
• Use for water heating only. Never alter in anyway or use with
any device or part not expressly approved by BaseCamp.
• This appliance is designed to be used with a source water
temperature of 60°F or below
• The maximum temperature rise from the appliances 35º F to
the shower head and 42º F to the tap from the source water
temperature
• For safety the appliance is designed to shut off the burner
when the water temperature from either of the outlets
reaches 125°°F
• XB13 will operate up to 75 minutes between battery changes
• The average run time for the XW18 from a fully charged
battery is 20 to 30 mins before it will require recharging
• The XW18 can be operated while connected to AC or DC,
however the battery will only receive charge when pump is
not operating. When the pump is off the battery will receive
charge.
• During operation ensure that all air inlets and exhaust
(front,sides and back) are kept free from obstructions and
closure.
CONTROL PANEL
TEMPERATURE CONTROL KNOB
MODEL (XB13)MODEL (XW18)
TEMPERATURE CONTROL KNOB
OPERATING SHOWER INSTRUCTIONS
1. MODEL (XB13) Make sure to insert 4 D cell batteries in the
pump power pack and 2 D cell batteries in under side of battery
compartment.. (Fig.1)Attach pump hose with quick connect fitting
to the back inlet hose connection.(Fig.2)
AIR INLETS
AND
EXHAUST
SAFETY FEATURES
This appliance is equipped with the following safety
features:
• Over Temperature Sensor – the appliance will not
allow the burner to remain in operation once the outlet
water temperature reaches 125ºF.
• Water Flow Sensor – water must be flowing through
the system to allow the burner to ignite. In the case
that the water supply is restricted or ceases, the burner
will be extinguished and will not relight.
• Tilt Switch – in the event that the appliance is moved
during operation or is being operated on an unstable
or non-solid surface the appliance will shut down and
must be switched off until a suitable surface is located.
Fig. 1
Fig. 2
Model (XW18) Have the heater fully charged or AC input
plugged in also have the pump plugged in properly.
AC INPUT
PUMP INPUT
Basecamp, Inc. | Portable Shower Operating Instructions and Owner’s Manual
4
3. Attach the shower hose using the Quick Connect Fitting. Model
XB13 attaches to inlet connection located on the front side of
shower. (Fig. 2)
Model XW18 attaches to the faucet. (Fig. 3)
XB13
Fig. 2 Fig. 3
4. Submerge the pump in a suitable reservoir of water. Maintain
pump fully submerged in water as the pump is being used as
pump motor can be damaged if not.
DO NOT use water direct from rivers, lakes sediments
from these bodies of waters can damage pump and the
appliance. DO NOT use in ocean in which salt water can
damage the pump and appliance.
WARNING: there are possible health effects from microbes
that might be present in these bodies of waters rivers, lakes
and oceans.
5. Screw propane clockwise into shower regulator then depress
the power button,the electronic ignition should be heard
igniting the burner. The XB13 model press the start button
on the pump power pack.
XW18
OPERATING TAP
INSTRUCTIONS(Model XW18 Only)
1. Swing the tap away from its storage position and locate towards the side of the appliance and locate a basin or bucket
beneath and locate the water flow to the central position.
2. The water temperature can be adjusted by moving the flow
valve between “Min & Max” as this will slow or increase the
water flow resulting in an increase or decrease in the outlet
temperature.
IMPORTANT: Running water for an extended period of time
in the low flow position (-) can trigger the High Limit Switch
causing burner to stop.
6. Take care to measure the temperature of the water from the
shower head, the temperature can be adjusted by turning the
temperature control knob until the desired level is reached.
IMPORTANT – Water remaining in the heat exchanger while the
flow is stopped may become hot. When the flow is resumed the
user must check the temperature output to ensure that it is
suitable and not too hot.
APPLIANCE POWER & CHARGING
(Model XW18)
1. The appliance is fitted with a 15V 5A/hr battery pack and can
be recharged with the AC adaptors /supplied.
2. Check the “Battery Indicator” that sufficient power is
available, if not connect to the AC adaptor.
Basecamp, Inc.| Portable Shower Operating Instructions and Owner’s Manual
5
3. Connect to the power inlet socket at the rear of the appliance
and the battery Indicator LED will stay a steady “RED” confirming that the battery is now charging. Once the unit is fully
charged the battery Indicator LED will change to “Green”.
.
AC INPUT
4. AC: Connect the three (3) pin plug to a suitable outlet then
connect to the appliance & switch on the AC outlet.
PUMP INPUT
MAINTENANCE
WARNING: To prevent personal injury unplug the appliance from
any electrical outlets.
STORING
1. Press the “Power” button & turn the
appliance off.
2. Disconnect all hoses and hold vertically allowing all excess
water to drain from them. With the shower head check that
the flow regulation switch is in the
“ON” position.
3. Return the tap to its locked position if
being used.
4. Unscrew the LP cylinder from the appliance
5. Unscrew the drain plug which is located on the underside
towards the pump inlet connection then tip the appliance
towards the back and to one side to drain excess water from
the heat exchanger via the water inlet.
• DO NOT USE – AC to DC converters or modify the adaptors
supplied with the appliance.
• Charge time from either power source is 4 hours, 50% battery
capacity can be reached after 2 hours however to maintain
battery life & condition it is recommended that the unit is
allowed to charge for the full 4 hours.
• IMPORTANT – If the appliance is not being used or is stored
it must be recharged every three months to guarantee the
battery life expectancy, failure to do so may result in
battery failure.
Using warm soapy water with a mild detergent wipe down all surfaces and areas of the appliance. DO NOT submerge the appliance
in a sink or bowl. DO NOT use abrasive cleaners or bleach. DO
NOT run soapy water through the heat exchanger.
WIRING DIAGRAM
CAUTION: Label all wires prior to disconnecting when servicing controls. Wiring errors can cause improper and dangerous operation.
The parts lists and wiring diagram show the appliance as it was constructed. Do not use a heater which is different from that
shown. Service should be done by qualified service technician.
Basecamp, Inc. | Portable Shower Operating Instructions and Owner’s Manual
MODEL:
XB13
6
WIRING DIAGRAM
MODEL:
XW18
TROUBLESHOOTING
PROBLEM SOLUTION
Check that appliance is switched on
Check sufficient water is available
Water will not flow
from shower head
Burner will
not light
Water is not
hot enough
Check gas control
Check source water
temperature
Check that the pump is connected to the appliance
Make sure the battery is charged
Check for kinks in shower hose
Check that pump fuse is not blown
Check that the shower flow water regulator is in the open position
Check that gas cylinder is turned on and that there is gas in cylinder
Check that the water is flowing from shower head
Check that the water is not over temperature
Check that adequate AC power is available
Check that battery does not require re-charging
Check gas control
Check source water temperature
Cycle the water through the system back in to the source reservoir then through the appliance again
Model XW18 reduce flow using the flow valve
DO NOT ATTEMPT TO
MODIFY THE APPLIANCE
Basecamp, Inc.| Portable Shower Operating Instructions and Owner’s Manual
TROUBLE SHOOTING
This guide should be followed in case of failure of the
appliance to operate correctly. If symptoms persist
contact Technical Service 1-800-251-0001
7
PARTS DIAGRAM
MODEL: XB13
MODEL: XW18
Basecamp, Inc. | Portable Shower Operating Instructions and Owner’s Manual
8
PARTS LIST
MODEL: XB13 MODEL: XW18
Item # Description
1. Bottom Feet 35542 4 35542 4
2. Battery Cover 1 35547 1
3. High Limit Switch 35527 1 35526 1
4. Igniter 35525 1 35548 1
5. Control, Main 35549 1
6. Control Charging 35550 1
7. Switch, Tip-over 35546 1 35546 1
8. Gas Inlet Assembly 35528 1 35528 1
9. Ignition, Electrode 35530 1 35530 2
10. Ignition Electrode 35551 1
11. Switch, Flow Water 35544 1 35552 1
12. Gas Outlet Assembly 35533 1 35533 1
13. Handle Assembly Shower 35545 1 35545 1
14. Faucet Assembly 35553 1
15. Regulator Assembly 35534 1 35534 1
16. Switch Power Main 35535 1 35535 1
17. Drain Plug 35536 1 35536 1
18. Knob Control 35537 1 35537 1
19. Fuse Assembly 35554 1
20. Water Outlet Fitting 35529 1 1
21. Label Control Panel 35541 1 1
22. Label Control Panel 35555 1
23. Battery 12V 35556 1
24. Shower Head 35538 1 35538 1
25. Power Supply 35557 1
26. Pump Assembly, 12V 35558 1
27. Pump Assembly
Part Number QTY Part Number QTY
Please Contact
Manufacture
F273701 5ft Propane Hose Assembly (Swivel 1”-20 Male Throwaway Cylinder Thread X POL w/ Handwheel)
F273704 10ft Propane Hose Assembly (Swivel 1”-20 Male Throwaway Cylinder Thread X POL w/ Handwheel)
F273702 12ft Propane Hose Assembly (Swivel 1”-20 Male Throwaway Cylinder Thread X POL w/ Handwheel)
Basecamp, Inc.| Portable Shower Operating Instructions and Owner’s Manual
ACCESSORIES
9
OPERATING INSTRUCTIONS
AND OWNER’S MANUAL
WARNING:
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS
COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE
DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE
AGENCY.
PARTS ORDERING INFORMATION:
PURCHASING: Accessories may be purchased at any Basecamp local dealer or
direct from the factory
Model #
XB13
XW18
XB13
XW18
FOR INFORMATION REGARDING SERVICE
Please call Toll-Free 800-251-0001
www.mrheater.com
Our office hours are 8:00 AM – 5:00 PM, EST, Monday through Friday.
Please include the model number, date of purchase, and description of problem in
all communication.
LIMITED WARRANTY
Basecamp, Inc. warrants its appliances and accessories to be free from defects in
material and workmanship for a period of 1 year from date of purchase. Basecamp,
Inc. will repair or replace this product free of charge if it has been proven to be
defective within the 1-year period, and is returned at customer expense with proof
of purchase to Basecamp, Inc. within the warranty period.
Basecamp, Inc. reserves the right to make changes at any time, without notice or
obligation, in colors, specifications, accessories, materials and models.
Basecamp, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001
Basecamp is a registered trademarks of Mr. Heater, Inc.
© 2017, Basecamp/Mr. Heater. All rights reserved
Basecamp, Inc. | Portable Shower Operating Instructions and Owner’s Manual
ANSI Z21.96-2014•CSA B11.6-2014
10
Loading...