Page 1
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1. Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2. Remove alternator from vehicle and place on bench
or suitable work area.
3. Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4. Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5. Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6. Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7. Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8
.Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9. Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com
©2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1. Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2. Remove alternator from vehicle and place on bench
or suitable work area.
3. Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4. Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5. Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6. Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7. Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8
.Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9. Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com
©2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1. Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2. Remove alternator from vehicle and place on bench
or suitable work area.
3. Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4. Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5. Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6
. Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7. Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8
.Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9. Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com
©2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1. Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2. Remove alternator from vehicle and place on bench
or suitable work area.
3. Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4. Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5. Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6
. Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7. Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8
.Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9. Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com
©2000 Printed in U.S.A.
100138-Inst.MRG5320 Alum Pulley 9/11/02 2:22 PM Page 1
Loading...