Please read this manual carefully before installation and keep it for future reference.
Remote Control
User Manual
Due to updates and constantly improving performance, the information and instructions within this
manual are subject to change without notice. Please visit www.mrcool.com/documentation to
ensure you have the latest version of this manual.
Version Date: 09-29-21
For more info visit www.mrcool.com
Contents
Remote Controller Specifications & Quick Start Guide .............. 2
1
Handling the Remote Controller .................................................. 3
2
Easy Pro™ Remote Controller ....................................................... 4
3
Buttons & Functions
............................. 4
Remote Screen Indicators ................. 5
How to Use Basic Functions ............. 6
Setting the Timer .................................. 8
How to Use Advanced Functions .... 8
Easy Pro™ Remote Controller
Model #: RG10A (DS2)/BGEFU1
DIY® E-Star™ Remote Controller .................................................. 12
4
Buttons & Functions .
...........................12
Remote Screen Indicators ................13
How to Use Basic Functions ............ 14
Setting the Timer ................................. 16
How to Use Advanced Functions .....17
®
DIY
E-Star™ Remote Controller
Model #: RG10A4(D1)/BGEFU1
Page 1 mrcool.com
Remote Control Specifications
My Mode
Swing
Mode
On/Off
Fan
Sleep
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
SET TEMPERATURE
Installation Summary
& Quick Start Guide
Model
Rated Voltage
Signal Receiving
Range
Operational
Temperature Range
Quick Start Guide
1
2
1
DIY® E-Star™: RG10A4(D1)/BGEFU1
Easy Pro™: RG10A (DS2)/BGEFU1
3.0V (Dry Batteries R03/LR03 x 2)
26.25 ft. (8m)
23°F ~ 140°F (-5°C ~ 60°C)
3
AUTO
COOL
DRY
HEAT
FAN
FIT BATTERIES
6
POINT REMOTE TOWARD UNITPRESS POWER BUTTON
SELECT MODE SELECT TEMPERATURE
5 4
SELECT FAN SPEED
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections
of this manual for more detailed instructions of how to operate the unit.
SPECIAL NOTE
Button designs on your remote may differ slightly from the example shown.
•
If the indoor unit is not equipped with a particular function, but your remote controller has
•
a button for it, pressing that function’s button on the remote control will have no effect.
When there are differences between the “Remote Controller Manual” and the “USER’S
•
MANUAL” when it comes to function description, the description of “USER’S MANUAL”
should take precedence.
mrcool.com
Page 2
Handling the Remote Controller
2
Inserting and Replacing Batteries
Your air conditioning unit may come with two
batteries (some units). Install the batteries in the
remote control before use by following the steps
below:
1. Slide the back cover from the remote control
downward to expose the battery compartment.
2. Insert the batteries, making sure to match the (+)
and (-) designations on the end of the batteries
with the symbols inside the battery compartment.
3. Reinstall the back cover by sliding it back into
place.
BATTERY NOTES
For optimum product performance:
• Do not mix old and new batteries, or
batteries of different types.
• Do not leave batteries in the remote
control if the device will not be used for
more than 2 months.
BATTERY DISPOSAL
DO NOT dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
• The remote control must be used within 26 ft
(8 m) of the unit.
• The unit will beep when remote signal is
received.
• Curtains, other materials and direct sunlight
can interfere with the infrared signal receiver.
Remove batteries if the remote will not be
used more than 2 months.
NOTES FOR USING REMOTE CONTROL
The device should comply with the local
national regulations.
• In Canada, it should comply with
CAN ICES-3(B)/NMB-3(B).
• In the USA, this device complies with part 15
of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and radiates radio
frequency energy. If it is not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference
by using one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
• Changes or modifications not approved by
the party responsible for compliance could
void user’s authority to operate the
equipment.
Page 3 mrcool.com
Operation Of Buttons
Easy Pro™ Remote Controller
3
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use Basic Functions section of this manual.
ON/OFF
Turns the unit on or off.
TEMP
Increases temperature in
1°F (1°C) increments.
Maximum Temperature
setting is 86°F (30°C).
NOTE: Press together &
buttons at the same
time for 3 seconds will
alternate the temperature
display between °C & °F.
Scrolls through operation
functions in following
sequence:
Sleep ( ) Follow Me ( )
AP Mode ( )
The selected symbol will
flash on the display window,
press the OK button to
confirm.
Decreases temperature
in 1°F (1°C) increments
Minimum temperature
setting is 60°F (16°C).
Selects fan speeds in the
following sequence:
AU 20% 40% 60%
80% 100%
Press the TEMP or
button to increase or
decrease the fan speed in
1% increments.
Starts and stops the horizontal
louver movement. Hold down
for 2 seconds to initiate vertical
louver auto swing feature.
TEMP
FAN SPEED
SET
SWING
MODE
Scrolls through operation modes in
the following sequence:
AUTO COOL DRY HEAT FAN
NOTE: HEAT mode is not supported
by the cooling-only version.
ECO/GEAR
Press this button to enter the energy
efficient modes which can be selected
in the following sequence:
ECO GEAR (75%) GEAR (50%)
Previous setting mode ECO
OK
Used to confirm the selected
functions.
TIMER
Used to set the timer to turn the unit
on or off at a specified time.
BREEZE AWAY
This feature keeps direct airflow
from blowing directly on the
occupants of the room.
NOTE: This feature is only available
in COOL, FAN, and DRY modes.
CLEAN
Used to start/stop the Self-Clean or
Active Clean function (Model
dependent, please refer to the
USER’S OPERATION & INSTALLATION
MANUAL).
LED
Turns the indoor unit’s LED display
and air conditioner buzzer on and off
(model dependent), to create a quiet
environment.
TURBO
Enables unit to reach the preset
temperature in the shortest possible
time.
Page 4mrcool.com
Remote Screen Indicators
Remote Screen Indicators
Information that is displayed when the remote controller is turned on.
Breeze Away display (some units)
Active clean feature display
Sleep mode display
Follow me feature display
Wireless control feature display(some units)
Transmission:
This indicator lights up
when the remote
transmits a signal to the
indoor unit.
TIMER ON display
TIMER OFF display
Silence:
This indicator lights
up when the Silence
function is activated.
FAN SPEED:
Displays selected fan speed:
Silence
1%
LOW
MED
HIGH
AUTO
NOTE: The fan speed cannot be
adjusted in AUTO or DRY mode.
Not all the models can display
*
the fan speed values between
AU-100%.
*
2%-20%
21%-40%
41%-60%
61%-80%
81%-100%
*
Low battery detection display (If flashes)
MODE display
Displays the current mode,
including:
ECO display
Displays when ECO feature
is activated
GEAR display
Displays when GEAR feature
is activated
LOCK display
Displays when LOCK feature
is activated
Temperature/Timer/Fan
speed display
Displays the set temperature
by default, or fan speed or
timer setting when using
TIMER ON/OFF functions.
*
*
*
*
Horizontal louver
swing display
Vertical louver
auto swing display
TURBO MODE display
Not available for
this unit.
• Temperature range:
60-86°F (16-30°C)/
68°F-82°F (20-28°C)
(model dependent)
• Timer setting range:
0-24 hours
• Fan speed setting range:
AU - 100%
This display is blank when
operating in FAN mode.
NOTE: All indicators shown are for demonstration purposes. During actual operation, only
the relative and active functions will be shown in the display window.
Page 5 mrcool.com
How to Use Basic Functions
How to Use Basic Functions
ATTENTION
Please ensure the unit is plugged in and power is available before operation.
AUTO Mode
Select AUTO mode Set your desired temperature
MODE
NOTE:
•
In AUTO mode, the unit will automatically select COOL, FAN, or HEAT function
based on the set temperature.
• In AUTO mode, fan speed cannot be set or adjusted by the user.
Turn on the air conditioner
COOL or HEAT Mode
Select COOL/HEAT
mode
MODE
Set the temperature
Set the fan speed
Turn on the air
conditioner
DRY Mode
Select DRY mode
MODE
NOTE: In DRY mode, fan speed cannot be set because it is automatically controlled.
Set your desired temperature Turn on the air conditioner
FAN Mode
Select FAN mode Turn on the air conditioner
MODE
NOTE: In FAN mode, the temperature cannot be set or adjusted. As a result, no
temperature reading will display on the remote screen.
Set the fan speed
Page 6mrcool.com
Setting the Timer
ON/OFF
M
ODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEMP
S
L
E
EP
ON/O
FF
MODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEM
P
SL
E
EP
ON/O
FF
MODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEMP
S
L
E
EP
How To Use The Buttons
Setting the TIMER
TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
Press TIMER button to
initiate the ON time
sequence.
Press Temperature UP or DOWN
button to set the desired time to
turn ON the unit.
Point remote control at the unit
and wait 1 second, the
TIMER ON will be activated.
TIMER
x5
1sec
ON/O
FF
MODE
SHORT
CUT
F
AN
TEMP
TIMER ON
S
L
E
EP
TIMER OF
F
TIMER OFF setting
Press TIMER button to
initiate the OFF time
sequence.
TIMER
Press Temperature UP or DOWN
button to set the desired time to
turn OFF the unit.
x10
NOTE:
• When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes
increments with each press, up to 10 hours. After 10 hours and up to 24, it will
increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press
10 times to get 5h,) The timer will revert to 0.0 after 24.
• Cancel either function by setting its timer to 0.0h.
TIMER ON & OFF setting (example)
NOTE: Keep in mind that the time periods you set for both functions refer to hours after
the current time.
TIMER
xn
TIMER
Point remote control at the unit
and wait 1 sec, the
TIMER OFF will be activated.
1sec
xn
xn
Timer
starts
Unit turns
ON
Unit turns
OFF
Example: If current time is 1:00PM,
and the timer is set using the above
steps, the unit will turn on 2.5 hours
Current
time 1 PM
2 PM 3 PM
2.5 hours later
5 hours later
3:30 PM
4 PM 5 PM
6 PM
later (3:30PM) and then turn off
at 6:00PM (5 hours after the timer
is originally set).
Page 7 mrcool.com
How To Use Advanced Functions
How to Use Advanced Functions
Swing function
Press the SWING button
2s
Swing
The horizontal louver will swing up and down
automatically when pressing SWING button.
Press it again to make it stop.
Keep pressing the SWING button more than 2
seconds, this will activate the vertical louver
swing function (Model dependent).
Swing
Airflow direction
If continue to press the SWING button, five
different airflow directions can be set. The
Swing
NOTE: When the unit is off, press and hold the MODE and SWING buttons together for one
second, the louver will move to an extreme angle to make it easier to clean. Press and hold
the MODE and SWING buttons together again for one second to reset the louver to its original
position (Model dependent).
louver can be moved to a different angle each
time you press the button. Continue pressing
the button until the desired setting is reached.
LED Display
LED LED
Press the LED button to either turn on or off
the display on the indoor unit.
Press LED button Press and hold the LED button
5s
more than 5 seconds (some units).
Press and hold the LED button more than 5
seconds, to make the display of the indoor unit
show the actual room temperature. Press and
hold the LED button for more than 5 seconds
again and the display will revert back to the set
temperature.
Page 8mrcool.com
How To Use Advanced Functions
ECO/GEAR function
Pressing the iECO/GEAR button will allow you to select the energy efficiency
modes in the following sequence:
ECO GEAR (75%) GEAR (50%) Previous setting mode ECO......
NOTE: This function is only available under the COOL mode.
ECO operation:
Under COOL mode, press this button and the remote controller will automatically adjust the
temperature to 75°F (24°C), fan speed off of AUTO to save energy. However, this only occurs when
the set temperature is less than 75°F (24°C). If the set temperature is above 75°F (24°C), pressing the
ECO button will cause the fan speed to change to AUTO and the set temperature will remain
unchanged.
NOTE:
• Pressing the ECO/GEAR button, modifying the mode, or adjusting the set temperature to
less than 75°F (24°C), will stop ECO operation.
• Under ECO operation, the set temperature should be 75°F (24°C) or above, or it may result in
insufficient cooling. If the cooling feels insufficient, press the ECO button again to turn off
this feature.
GEAR operation:
Press the ECO/GEAR button to enter the GEAR operation as following:
75% (up to 75% electrical energy consumption)
50% (up to 50% electrical energy consumption)
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternate between electrical energy
consumption reading and the set temperature.
Silence function
2s
Pressing the FAN button for more than 2 seconds will activate or disable the Silence
function (some units).
Due to low frequency operation of compressor, this function could result in
insufficient cooling and heating capacity. Pressing the ON/OFF, MODE, SLEEP, TURBO
or CLEAN button while the system is operating with the silence function activated will
cancel it.
Page 9 mrcool.com
How To Use Advanced Functions
FP function
2
Using this function will cause the unit to operate with a high fan speed setting
(while the compressor is on) with temperature automatically set to the lowest
setting, 46°F (8°C), in order to achieve faster cooling.
NOTE: The function listed below is for heat pump air conditioners only.
Press the button 2 times within one second while in HEAT Mode and the temperature will be set to
60°F (16°C) or 68°F (20°C) (dependent on model) and the FP function will be activated.
Pressing the On/Off, Sleep, Mode, Fan or Temperature buttons while operating this function will
cancel it.
LOCK function
5s
Clean
5s
Turbo
+
Clean Function (some units)
Press CLEAN button
Airborne bacteria can grow in the moisture that condenses around heat
Clean
TURBO Function
exchanger in the unit. With regular use, most of this moisture is evaporated
from the unit. By pressing the CLEAN button, your unit will clean itself
automatically. After cleaning has been completed, the unit will turn off
automatically. Pressing the CLEAN button mid-cycle will cancel the operation
and turn off the unit. You can use the CLEAN function as often as you like.
NOTE: You can only activate this function in COOL or DRY mode.
Pressing the CLEAN and TURBO buttons at the same time for
more than 5 seconds will activate the LOCK function.
With this feature activated no buttons pressed will respond,
except when these two buttons are pressed again for two
seconds in order to disable the LOCK function.
Press TURBO button
Turbo
When the TURBO button is pressed while the unit is in COOL mode, the
unit will blow cool air with highest fan setting to speed up the cooling process.
When the TURBO button is pressed while the unit is in HEAT mode, for
units with electric heat elements, the electric heater will activate and speed up
the heating process.
Page 10mrcool.com
SET function
How To Use Advanced Functions
SET SET OK
Press the SET button to enter the function setting, then press the SET button or the TEMP or
buttons to select the desired function. The selected symbol will flash on the display, press the OK
button to confirm and this will activate the selected function.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Breeze Away ( ) Sleep ( ) Follow Me ( ) AP mode ( )
[ ]: If your remote controller has a Breeze Away button or Sleep button, you cannot use the
*
SET button to select the Breeze Away or Sleep feature.
Breeze Away function ( ) (some units):
This feature keeps airflow from being blown
directly on the occupants of the room.
NOTE: This feature is available under COOL,
FAN and DRY modes only.
Sleep function( ) :
The SLEEP function is used to decrease energy
use while you sleep (temperature settings
needed to stay comfortable during sleep differ
from the settings needed while awake). This
function can only be activated via the remote
control.
For further details, please refer to the Sleep
Operation section of your unit’s USER MANUAL.
NOTE: The SLEEP function is not available in
FAN or DRY mode.
AP function ( ) (some units):
Choose AP mode to use the wireless network
configuration. For some units, it does not work
by pressing the SET button. To enter the AP
mode, continuously press the LED button
seven times within 10 seconds.
*
or
Follow me function ( ):
The FOLLOW ME function enables the remote
control to measure the temperature at the
location it currently is and send this signal to
the air conditioning unit in a 3 minute interval.
When using AUTO, COOL, or, HEAT modes,
measuring the ambient temperature from the
remote control (instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature where you currently
are and ensure maximum comfort.
NOTE: Press and hold the TURBO button for
seven seconds to start or stop the memory
feature of the FOLLOW ME function.
If the memory feature is activated, “ON”
will display for 3 seconds on the screen.
If the memory feature is stopped, “OF”
will display for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the
Follow Me function.
Page 11 mrcool.com
DIY® E-Star™ Remote Controller
4
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how
to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.
ON/OFF
Turns the unit on or off.
TEMP
Increases temperature in
1°F (1°C) increments.
Maximum Temperature
setting is 86°F (30°C).
Scrolls through operation
functions in following
sequence:
Sleep ( ) Follow Me ( )
AP Mode ( )
The selected symbol will
flash on the display window,
press the OK button to
confirm.
Decreases temperature
in 1°F (1°C) increments
Minimum temperature
setting is 62°F (17°C).
Selects fan speeds in the
following sequence:
AUTO LOW MED HIGH
NOTE: Pressing and holding
this button for 2 seconds
will activate the SILENCE
feature.
SET
TEMP
FAN SPEED
MODE
Scrolls through operation modes in
the following sequence:
AUTO COOL DRY HEAT FAN
NOTE: HEAT mode is not supported
by the cooling-only version.
ECO
Press this button to enter the energy
efficient mode.
OK
Used to confirm the selected
functions.
TIMER
Used to set the timer to turn the unit
on or off at a specified time.
SHORTCUT
Used to restore the current settings
or resume previous settings.
CLEAN
Used to start/stop the Self-Clean
function.
LED
Turns the indoor unit’s LED display
and air conditioner buzzer on and off
(model dependent), to create a quiet
environment.
SWING
Starts and stops the horizontal
louver movement. Hold down
for 2 seconds to initiate vertical
louver auto swing feature.
NOTE: Press and hold the temperature & buttons at the same time for 3 seconds and it will
alternate the temperature display between °F and C° readings.
TURBO
Enables unit to reach the preset
temperature in the shortest possible
time.
Page 12mrcool.com
Remote Screen Indicators
Remote Screen Indicators
Information that is displayed when the remote controller is turned on.
Sleep mode display
Follow me feature display
Wireless control feature display
Transmission:
This indicator lights up
when the remote
transmits a signal to the
indoor unit.
Low battery detection display (If flashes)
MODE display
Displays the current mode,
including:
TIMER ON display
TIMER OFF display
Silence:
This indicator lights
up when the Silence
function is activated.
FAN SPEED:
Displays selected fan speed:
Silence
LOW
MED
HIGH
AUTO
NOTE: The fan speed cannot be
adjusted in AUTO or DRY mode.
ECO display (some units)
Displays when ECO feature
is activated.
LOCK display
Displays when LOCK feature
is activated.
Temperature/Timer/Fan
speed display
Displays the set temperature
by default, or fan speed or
timer setting when using
TIMER ON/OFF functions.
• Temperature range:
62-86°F (17-30°C)/
68°F-82°F (20-28°C)
(model dependent)
• Timer setting range:
0-24 hours
This display is blank when
operating in FAN mode.
NOTE: All indicators shown are for demonstration purposes. During actual operation, only
the relative and active functions will be shown in the display window.
Page 13 mrcool.com
How To Use Basic Functions
How to Use Basic Functions
ATTENTION
Please ensure the unit is plugged in and power is available before operation.
SETTING TEMPERATURE
The operating temperature range for units is
62-86°F (17-30°C) or 68-82°F (20-28°C)
(model dependent). You can increase or
decrease the set temperature in 1°F (1°C)
increments by using the the Temperature
or buttons on the remote.
AUTO Mode
In AUTO mode, the unit will automatically select
1
3
2
the COOL, FAN, or HEAT operating mode based
on the set temperature. To select AUTO mode
follow these steps:
1. Press the MODE button and select AUTO
mode.
2. Set your desired temperature using the
TEMPERATURE or buttons.
3. Press the ON/OFF button to start the unit.
NOTE: FAN speed cannot be set or adjusted
in AUTO mode.
COOL Mode
To select COOL Mode follow these steps:
1. Press the MODE button and select COOL
mode.
2. Set your desired temperature using the
TEMPERATURE or buttons.
3. Press the FAN button to select the desired fan
speed: AUTO, LOW, MED, or HIGH.
4. Press the ON/OFF button to start the unit.
1
4
2
3
Page 14mrcool.com
How To Use Basic Functions
DRY Mode (dehumidifying function)
In DRY mode, the unit acts as a dehumidifier.
1
3
2
To select DRY mode follow these steps:
1. Press the MODE button and select DRY mode.
2. Set your desired temperature using the
TEMPERATURE or buttons.
3. Press the ON/OFF button to start the unit.
NOTE: FAN speed cannot be set or adjusted
in DRY mode.
FAN Mode
1. Press the MODE button and select FAN
mode.
2. Press FAN button to select the desired the fan
speed: AUTO, LOW, MED, or HIGH.
3. Press the ON/OFF button to start the unit.
NOTE: The temperature cannot be set or
adjusted in FAN mode. As a result of this, the
remote control LCD display will not display
the temperature.
1
4
2
3
1
3
2
HEAT Mode
To select HEAT mode follow these steps:
1. Press the MODE button and select HEAT
mode.
2. Set your desired temperature using the
TEMPERATURE or buttons.
3. Press the FAN button to select the desired
fan speed: AUTO, LOW, MED, or HIGH.
4. Press the ON/OFF button to start the unit.
NOTE: As the outdoor temperature drops,
the performance of the unit’s HEAT function
may be affected. If this occurs, we
recommend using other heating appliances
in conjunction with the unit.
Page 15 mrcool.com
Setting the Timer
ON/OFF
M
ODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEMP
S
L
E
EP
ON/O
FF
MODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEM
P
SL
E
EP
ON/O
FF
MODE
F
AN
SHORT
CUT
TIMER ON
TIMER OF
TEMP
S
L
E
EP
Setting the TIMER
TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
Press TIMER button to
initiate the ON time
sequence.
Press Temperature UP or DOWN
button to set the desired time to
turn ON the unit.
Point remote control at the unit
and wait 1 second, the
TIMER ON will be activated.
TIMER
x5
1sec
ON/O
FF
MODE
SHORT
CUT
F
AN
TEMP
TIMER ON
S
L
E
EP
TIMER OF
F
TIMER OFF setting
Press TIMER button to
initiate the OFF time
sequence.
TIMER
Press Temperature UP or DOWN
button to set the desired time to
turn OFF the unit.
x10
NOTE:
• When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes
increments with each press, up to 10 hours. After 10 hours and up to 24, it will
increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press
10 times to get 5h,) The timer will revert to 0.0 after 24.
• Cancel either function by setting its timer to 0.0h.
TIMER ON & OFF setting (example)
NOTE: Keep in mind that the time periods you set for both functions refer to hours after
the current time.
TIMER
xn
TIMER
Point remote control at the unit
and wait 1 sec, the
TIMER OFF will be activated.
1sec
xn
xn
Timer
starts
Unit turns
ON
Unit turns
OFF
Example: If current time is 1:00PM,
and the timer is set using the above
steps, the unit will turn on 2.5 hours
Current
time 1 PM
2 PM 3 PM
2.5 hours later
5 hours later
3:30 PM
4 PM 5 PM
6 PM
later (3:30PM) and then turn off
at 6:00PM (5 hours after the timer
is originally set).
Page 16mrcool.com
How To Use Advanced Functions
How to Use Advanced Functions
Swing function
Press the SWING button
2s
Swing
The horizontal louver will swing up and down
automatically when pressing SWING button.
Press it again to make it stop.
Silence function
2s
LED Display
Pressing the FAN button for more than 2 seconds will activate or disable the Silence
function (some units).
Due to low frequency operation of compressor, this function could result in
insufficient cooling and heating capacity. Pressing the ON/OFF, MODE, SLEEP, TURBO
or CLEAN button while the system is operating with the silence function activated will
cancel it.
Swing
Keep pressing the SWING button more than 2
seconds, this will activate the vertical louver
swing function (Model dependent).
LED LED
Press the LED button to either turn on or off
the display on the indoor unit.
Press LED button Press and hold the LED button
5s
more than 5 seconds
(some units).
Press and hold the LED button more than 5
seconds, to make the display of the indoor unit
show the actual room temperature. Press and
hold the LED button for more than 5 seconds
again and the display will revert back to the set
temperature.
Page 17 mrcool.com
How To Use Advanced Functions
ECO function
Pressing the ECO button will enter the unit into energy efficiency mode.
NOTE: This function is only available under the COOL mode.
ECO operation:
Under COOL mode, press this button and the remote controller will automatically adjust the
temperature to 75°F (24°C), fan speed off of AUTO to save energy. However, this only occurs when
the set temperature is less than 75°F (24°C). If the set temperature is above 75°F (24°C), pressing the
ECO button will cause the fan speed to change to AUTO and the set temperature will remain
unchanged.
NOTE:
• Pressing the ECO/GEAR button, modifying the mode, or adjusting the set temperature to
less than 75°F (24°C), will stop ECO operation.
• Under ECO operation, the set temperature should be 75°F (24°C) or above, or it may result in
insufficient cooling. If the cooling feels insufficient, press the ECO button again to turn off
this feature.
FP function
2
Using this function will cause the unit to operate with a high fan speed setting
(while the compressor is on) with temperature automatically set to the lowest
setting, 46°F (8°C), in order to achieve faster cooling.
NOTE: The function listed below is for heat pump air conditioners only.
Press the button 2 times within one second while in HEAT Mode and the temperature will be set to
60°F (16°C) or 68°F (20°C) (dependent on model) and the FP function will be activated.
Pressing the On/Off, Sleep, Mode, Fan or Temperature buttons while operating this function will
cancel it.
LOCK function
5s
Clean
+
5s
Pressing the CLEAN and TURBO buttons at the same time for
more than 5 seconds will activate the LOCK function.
Turbo
With this feature activated no buttons pressed will respond,
except when these two buttons are pressed again for two
seconds in order to disable the LOCK function.
Page 18mrcool.com
How To Use Advanced Functions
SHORTCUT function
Press SHORTCUT button(some units) to revert to previous settings:
Pressing the SHORTCUT button when the remote controller is on will cause
the system to automatically revert back to the previous settings including the
operating mode, set temperature, fan speed level, and the sleep feature
(if activated).
If the SHORTCUT button is pressed for more than 2 seconds, the system will
automatically restore the current operation settings including the operating
mode, set temperature, fan speed level and sleep feature (if activated).
Clean Function
Press CLEAN button
Airborne bacteria can grow in the moisture that condenses around heat
Clean
exchanger in the unit. With regular use, most of this moisture is evaporated
from the unit. By pressing the CLEAN button, your unit will clean itself
automatically. After cleaning has been completed, the unit will turn off
automatically. Pressing the CLEAN button mid-cycle will cancel the operation
and turn off the unit. You can use the CLEAN function as often as you like.
TURBO Function
Press TURBO button
Turbo
NOTE: You can only activate this function in COOL or DRY mode.
When the TURBO button is pressed while the unit is in COOL mode, the
unit will blow cool air with highest fan setting to speed up the cooling process.
When the TURBO button is pressed while the unit is in HEAT mode, for
units with electric heat elements, the electric heater will activate and speed up
the heating process.
Page 19 mrcool.com
SET function
How To Use Advanced Functions
SET SET OK
Press the SET button to enter the function setting, then press the SET button or the TEMP or
buttons to select the desired function. The selected symbol will flash on the display, press the OK
button to confirm and this will activate the selected function.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Sleep ( ) Follow Me ( ) AP mode ( )
*
[ ]: If your remote controller has a Sleep button, you cannot use the SET button to select
*
the Sleep feature.
Sleep function ( ):
The SLEEP function is used to decrease energy
use while you sleep (temperature settings
needed to stay comfortable during sleep differ
from the settings needed while awake). This
function can only be activated via the remote
control.
For further details, please refer to the Sleep
Operation section of your unit’s USER MANUAL.
NOTE: The SLEEP function is not available in
FAN or DRY mode.
AP function ( ) (some units):
Choose AP mode to use the wireless network
configuration. For some units, it does not work
by pressing the SET button. To enter the AP
mode, continuously press the LED button
seven times within 10 seconds.
or
Follow me function ( ):
The FOLLOW ME function enables the remote
control to measure the temperature at the
location it currently is and send this signal to
the air conditioning unit in a 3 minute interval.
When using AUTO, COOL, or, HEAT modes,
measuring the ambient temperature from the
remote control (instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature where you currently
are and ensure maximum comfort.
NOTE: Press and hold the TURBO button for
seven seconds to start or stop the memory
feature of the FOLLOW ME function.
If the memory feature is activated, “ON”
will display for 3 seconds on the screen.
If the memory feature is stopped, “OF”
will display for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the
Follow Me function.
Page 20mrcool.com
Due to updates and constantly improving performance, the information and instructions within this
manual are subject to change without notice. Please visit www.mrcool.com/documentation to
ensure you have the latest version of this manual.
Version Date: 09-29-21
Loading...