Mpman PC36 Operating Instructions

1. PARTS OF THE CAMCORDER 4
2. PREPARING FOR USING 6
INSTALLING THE BATTERY 6 CHARGING THE BATTER Y 7 INSERTING THE MEMORY CARD 8 SETTING THE LANGUAGE 9 SETTING THE DATE AND TIME 10 MONITOR SCREEN DISPLA Y 11
3. USING THIS CAMCORDER 14
TURNING THE CAMCORDER ON AND OFF 14 CHANGE THE RECORD MODE 14 RECORDING A VIDEO CLIP 15 TAKING STILL IMAGES 16 USING THE SELF-TIMER 17 USING THE FLASH 18 RECORDING AUDIO 19
4.USING THE MENU IN RECORD MODE 19
MENU IN CAPTURE MODE 19 MENU IN VIDEO MODE 22
1
SETUP MENU 23
5.PLAYBACK 26
PLAYING BACK MOVIE CLIPS 26 PLAYBACK STILL IMAGE 26 PLAYING BACK AUDIO FILES 27 OTHER FUNCTION IN PLAYBACK MODE 27
6. MAKING CONNECTIONS 30
CONNECTING THE CAMCORDE R T O A TV 30 CONNECTING THE CAMCORDE R T O A HDTV 31 CONNECTING THE CAMCORDE R T O A PC 32
7. SOFTWARE INSTALLATION 33
INSTALLING THE SOFTWARE 33
8. TROUBLESHOOTING 37
9. TECHNICAL SPECIFICATIONS 38
2
Thank you for purchasing this product. Please read these operating
instructions carefully in order to use the digital video camera correctly.
Keep the instructions in a safe place after reading so that you can refer to
them later.

Precautions

Before using the camcorder, please ensure that you read and understand
the safety precautions described below.
Do not try to open the case of the camcorder or attempt to modify this
camcorder in any way. Maintenance and repairs should be carried out
only by authorized service providers.
Keep the camcorder away from water and other liquids. Do not use the
camcorder with wet hands. Never use the camcorder in the rain or snow.
Moisture creates the danger of electric shock.
Use only the recommended power accessories. Use of power sources not
expressly recommended for this equipment may lead to overheating,
distortion of the equipment, fire, electrical shock or other hazards.
3

1. Parts of the camcorder

4
1. Configuration & Installation
1 Lens
Self-Timer Lamp
2
Flash Lamp
3
Microphone
4
Display Button
5
Upwards
Leftwards
Rightwards
Downwards
~
OK
6 Joystick
7 T / Zoom in Button
8 Menu Button
9 Shot Button
10 W / Zoom out Button
11 Speaker
12 Power Button
13 USB Jack
14 HDMI Jack
15 AV out
16 Strap Mount
17 Mode Button
18 LCD Monitor
5
19 Battery Holder
SD Card Slot
20
21 Battery & SD Card Door
Battery Room
22

2. Preparing for using

Installing the Battery

1. Slide the battery cover open as illustrated.
2. Place the accessory lithium-ion battery into the compartment. Note
that the metallic contacts must be aligned with the contacts in the
compartment.
3. After the battery is properly installed, replace the battery cover.
6

Charging the battery

Please charge the battery at least 8 hours for first time use.
1. Connect one end of the supplied USB cable to the USB port of the
camcorder and the other end to a powered PC. Make sure the
camcorder is powered off.
2. The charging LED turns red and the charge starts.
3. When the charging is interrupted or the battery pack is fully charged,
7
the charging LED will turn off.

Inserting the Memory Card

This camcorder has an internal memory, it can only record a few pictures or
movie clips. If you want record more you have to use a SD or MMC card.
Turn off the camcorder before inserting or removing the memory card. Be
sure to orient the card correctly when inserting it. Never try to force the
memory card into the slot when you feel resistance. The memory card has
a write protect switch, which used to protect data from accidental deletion.
Therefore, whenever you want to record, format or delete files in the SD
card, disable the write protection beforehand.
1. Turn off the camcorder.
2. Slide the battery cover and then you will see the SD card slot.
3. Insert the memory card as illustrated.
4. Close the battery cover.
• To release the memory card press the edge of the card gently.
8

Format the memory card

It is important to format the memory card when it is the first time you use
this camcorder. All data will be deleted including protected files. Be sure to
download important files to your computer before formatting.
1: Turn the power on, and set the camcorder to the Setup Menu.(See the
details on 23 )
2: Push the joystick upward or downward to select [Format] then push the
joystick rightward to launch the submenu.
3: Push the joystick upward or downward to select the item [YES] and then
press the OK button to erase all data.

Setting the Language

When using the camcorder for the first time after purchasing it, be sure to
choose a language and set the date & time before using the camcorder.
1: Turn the power on, and set the camcorder to the Setup Menu.(See the
details on 23 )
2: Push the joystick upward or downward to select [Language] then move
the joystick rightward to launch the submenu.
9
3: Push the joystick upward or downward to select the desired language
and then press the OK button to confirm the setting.
4: Press the MENU button to close the menu.

Setting the date and time

1: Turn the power on, and set the camcorder to the Setup Menu. (See the
details on 23)
2: Push the joystick upward or downward to select [Date/Time] then push
the joystick rightward to launch the submenu: Date
Format, Date Setup.
3: Select a date format by using the joystick. And then
select [Date Setup].
4: Push the joystick upward or downward to change the
highlighted value. Push the joystick leftward or
rightward to move the cursor between settings.
5: Press the OK button to confirm the setting. 6: Press the MENU button to close the menu.
• The date and time can be only added to still images by setting the
10
function [Date Stamp] in capture menu.
Monitor screen display Capture
11
Video record mode
12
Playback mode
13

3. Using this camcorder

Turning the Camcorder On and Off

1. Open the LCD panel. Press the POWER button to turn on the
camcorder.
2. Press the POWER button again to turn the camcorder off.
To save battery power, the LCD monitor automatically turns off 30 seconds
after the last control accessed (factory-preset setting). Press any button
other than the power button to turn on the LCD monitor. After the power
saving function has been active for the set time, the power will turn off
completely. Press the Power button to power the camera back on. You can
change the power-off time by setting the function [Auto off] in the Setup
menu.

Change the record mode

There are three record modes in this camcorder.
1: Press the POWER button to turn on the camcorder
14
2: Press the MODE button to change the mode. Each time the MODE
button is pressed the mode icon is changed.
Display Title Description
Capture mode For taking still photos.
Video mode For recording movie clips.
Audio mode For recording audio files.
• You can quickly switch the camcorder to video mode or playback
mode by using the video/playback switch. Push the video/playback switch downward to set the camcorder to playback mode
push it upward to set it to video mode.
and

Recording a video clip

1: Turn on the camcorder and set the camcorder to video record mode
).
(
15
Press the SHUTTER button to start recording. Press the SHUTTER
2:
again to end the recording. If the memory is full the video camera will stop
recording automatically.
3: You can press
focus. When the picture is enlarged press the
SHUTTER button to lock the zoom ratio and end the
recording.
• On the upper of the LCD monitor displays the reco rded time.
T button or W button to adjust the

Taking still images

1. Turn on the camcorder.
2. Press the MODE button to set the camcorder to capture mode, the
appears on the LCD screen.
icon
3. Adjust the focus: press
adjust the focus.
T button or W button to
4. Hold the camcorder steady and then press the
SHUTTER button completely down to take a picture.
• Automatically the number displayed on the
16
screen is increased by one. For example, if the screen displays 3/2 0 when the camera is powered on, after one photo has been captured, 4/20 will appear. If the memory is full, “Memory Full “ will appear on screen.
• Make sure that your fingers do not cover the lens.

Using the Self-timer

Use the self-timer to set a delay from the time the shutter button is pressed
to the time the image is shot.
1: Turn the power on, and set the camcorder to the Capture mode.
2: Press the MENU button to display the capture menu.
3: Using the joystick to select the item [Self Timer]. And move the joystick
rightward to launch the submenu:
Disable: Don’t use self-timer.
10 Seconds: The shutter release will delay for 10 seconds.
20 Seconds: The shutter release will delay for 20 seconds.
4: Move the joystick upward or downward to select the self timer.
17
5: Press the OK button to confirm the setting, and then press the MENU
button to close the menu.
6: Press the SHUTTER button to take picture.

Using the Flash

The flash is not only for taking pictures when there is insufficient light, but
also for when the subject is in shade or with backlight conditions. Pressing
the flash button cycles your camera through the various flash modes. The
flash will not activate during continuous shooting or movie recording.
1: Set the camcorder to the Capture mode.
2: Press the FLASH/DELETE button to change the flash mode.
Each time the flash button is pressed, the flash icon changes.
Auto: Automatically turn on/of
Flash on: Force on the flash
Flash off: Force off the flash
3: Press the SHUTTER button to take a picture.
18
• When the battery level is low the flash strobe will not work.
• The LCD screen is black when the flash is charging. The next image
can be shot only when charging is completed.

Recording audio

1: Turn the camcorder on and set it to audio record mode.
2: Press the SHUTTER button to start recording. 3: Press the SHUTTER again to end the recording. If the memory is full the
video camera will stop recording automatically.
• On the center of the LCD monitor displays the recorded time.
• There is no menu in audio record mode.

4.Using the menu in record mode

When a menu is displayed, the joystick is used to make the desired setting.
The audio record mode doesn’t have a menu.

Menu in capture mode

1: Turn on the camcorder and set it to capture
19
mode.
2: Press the MENU button to display the menu.
3: Move the joystick upward or downward to select an item.
4: Push the joystick rightward to enter the submenu.
5: Use the joystick to select the desired item.
6: Press the OK button to confirm the setting. 7: Press the MENU button to close the menu.
Capture menu list
Menu item Function
Resolution There are five options for choice:
[12M]/[8M] /[5M]/[3M].
Quality Select a lower image quality to decrease the image size in
order to capture more images. There are three options for
choice:[Super] /[Fine] /[Normal].
White
Balance
Adjust the white balance to suit different light sources.
There five items for option: [Auto]/[Daylight]/ [Cloudy] /
[Fluorescent] / [Tungsten].
20
Color
Effect
Exposure Set the exposure value manually to compensate for unusual
Date
Stamp
Self Timer Use the self-timer to set a delay from the time the shutter
Burst Use this function to take 3 pictures continuously.
Set the color effect to add a color tone to the picture.
[color]: Reflects the true color of the object.
[Sepia]: Adds a sepia color tone to the picture.
[Monochrome]: The pictures only have two colors: white
and black.
lighting conditions such as indirect indoor lighting, dark
backgrounds, and strong backlighting. The exposure value
range is –2.0 to 2.0.
This function can be used to add a date to your pictures as
you take them. There are two items for option:
[On]: Add the recording date & time to printed images.
[Off]: Do not add the recording date & time to printed
images.
button is pressed to the time the image is shot. [Disable]/[10
SEC]/[20SEC].
21
Snapshot [Single]: Press the shutter button once to take one picture.
[Burst]: Press the shutter button once to take three pictures
continuously.

Menu in video mode

1: In video record mode press the MENU
button to display the menu.
2: Move the joystick upward or downward to
select an item.
3: Push the joystick rightward to enter the submenu.
4: Use the joystick upward or downward to select the desired item.
5: Press the OK button to confirm the setting. 6: Press the MENU button to close the menu.
Menu item Function
Resolution Select small movie size to record longer time. There are
two items for option:[1280x720]/ [720x480].
Frame Rate Select low frame rate to record longer time. There are
22
two items for option: [30FPS]/[15FPS].
White Balance See the details on page 20.
Audio [Enable]: Voice is recorded when recording movie clip..
[Disable]: No voice is recorded when recording movie
clips.

Setup menu

You can set the system items in setup menu.
1: Turn the power on and press the MENU
button to display the menu.
2: Push the joystick rightward to select
[Setup].
3: Move the joystick upward or downward to select an item.
4: Push the joystick rightward to enter the submenu.
5: Push the joystick upward or downward to select the desired item.
6: Press the OK button to confirm the setting.
7: Press the MENU button to close the menu.
Menu item Function
23
Language Select a language for the Display menu and other
information from the following languages: [English]: English, [Français]: French, [Deutsch]:German, [Italiano]: Italian, [Español]: Spanish, [Portuguãs]:
Portuguese. [Nederlands]Dutch
Auto off To save power, the camcorder is turned off
automatically after a period of time. There are four
options: [Disable] / [1Min] / [3Min]/[5 Min].
TV output You can review images on a television with the supplied
AV cable. TV Out should be set to either NTSC or PAL
depending on your region.
[NTSC]: America, Japan and others; [PAL]: Europe,
Oceania and others.
Frequency Light Frequency should be set to either 60Hz or 50Hz
depending on your region. [50HZ] / [60HZ].
Date/Time Refer to page 9.
Buzzer Sets the operation sound on and off. [Enable] / [Disable]
24
Format To erase all data stored on the memory card if you are
using a memory card, or all data stored in the internal
memory if there is no card inserted. All data will be
deleted including protected files. Be sure to download
important files to your computer before formatting. [Yes]
/ [No].
Default
Settings
USB Mode You can use this camera as a PC camera or removable
Firmware
version
To reset the entire menu and button operation settings
to initial default.
disk. [PC Camera]:Use as a PC camera; [Mass storage]:
Use as a removable disk.
This function will show the software version.
25

5.Playback

Playing back movie clips

1: Set the camcorder to playback mode.
2: Push the joystick leftward or rightward to select the movie clips you want
to playback.
3: Press the SHUTTER button to start playing. Press the OK button to
pause it and press it again to continue. Push the joystick rightward to fast
forward and push the joystick leftward to back forward.
4: Push the joystick upward or downward to adjust the volume.

Playback still image

1: Set the camcorder to playback mode.
The latest recorded file appears on the LCD screen. If there are no
images stored, a message [No Image] appears.
2: Push the joystick leftward or rightward to preview the previous or next
image.
26
3: Zooming:
T button or W button to zoom in or zoom out the image. When the
Press
picture is enlarged press the SHUTTER button to lock the zoom ratio and
then you can push the joystick upward/downward/Leftward/Rightward to
browse the details of the image.

Playing back audio files

1: Set the camcorder to playback mode.
2: Push the joystick leftward or rightward to select the audio file you want to
playback.
3: Press the SHUTTER button to start playing. Press the SHUTTER button
to pause it and press it again to continue.

Other function in playback mode

Viewing Thumbnails
Press W button to view the file in thumbnails mode. Move the joystick
upward/downward/leftward/rightward to select a file. Press
T button to view
27
the file in full screen.
Delete files
If you want to delete a single file you have to select the file first and then
press the MENU button to display the menu. Select “ Delete Current”
or”Delete All”and then Push the joystick rightward to enter the submenu.
Move the joystick leftward to select “Yes” and then press the OK button to
delete the file or d
elete All files
Menu in playback mode
1: In playback mode press the MENU
button to display the menu.
2: Move the joystick upward or downward to
select an item.
3: Push the joystick rightward to enter the
submenu.
4: Move the joystick upward or downward to select the desired item.
5: Press the OK button to confirm the setting. 6: Press the MENU button to close the menu.
28
Menu item Function
Delete Current Use this function to delete a single file. [Yes]/[No].
Delete All Use this function to delete all files. [Yes]/[No].
Lock Use this function to protect the files from being deleted
by accident.
[Lock Current]: Lock the current file.
[Unlock Current]: Unlock the current file.
[Lock all]: Lock all files.
[Unlock All]: Unlock all files.
Thumbnail View all files in thumbnail mode.
[2x2]: The LCD screen display 4 files a page.
[3x3]: The LCD screen display 9 files a page.
Rotate Use this function to rotate the images.
[90]:Rotate the image 90 degrees in clockwise.
[180]: Rotate the image 180 degrees in clockwise.
[270]: Rotate the image 270 degrees in clockwise.
Slide show Play the files automatically.
29
[On]: Select this item to start playing.
[Setup]: Set the direction and Interval time of the slide
show .
[Direction]: [Backward] / [Forward].
[Interval]: [I Sec] / [10 Sec].
Print Use this function to print the images.[Yes]/[No]

6. Making connections

Connecting the Camcorder to a TV

When plug in the TV-out cable (supplied) to the camcorder output jack the
LCD screen turns black, Connect the camcorder to a TV and the TV screen
now performs as the camcorder LCD screen.
1. Connect the camcorder to a TV via the TV-out cable (supplied)
2. Turn on the TV and the camcorder, and then set the TV to “AV” mode.
3. When the camcorder is set to record mode, you can preview the
subjects you want to record on the TV screen.
30
4. When the camcorder is set to Playback mode, you can review all the
pictures, video and audio clips stored in the camera on the TV.

Connecting the Camcorder to a HDTV

HD-TV hereby means the HDTV built-in component input ports, thus can perform HD (720P) high resolution quality while connected.
1. Connect the camcorder to HDTV by the HDMI-cable.
2. Power on HDTV and switch to HDMI-mode.
3. Power ON the camcorder. Set the camcorder in playback mode.
Push the joystick leftward or rightward to select the file demanded.
4. Press SHUTTER button to “Play” the selected video file on HDTV,
press it again to “Stop” the playing.
5. Press the OK button to “Pause”, press it again to “Continue” the
playing.
6. Push the joystick leftward to reward, push the joystick rightward to
forward.
7. Push the joystick upward or downward to adjust the volume.
31

Connecting the Camcorder to a PC

There are two ways to download files from the camcorder's internal
memory or memory card to a computer:
By inserting the memory card into a card reader
By connecting the camera to a computer using the supplied USB
cable.

Using a Card Reader

1: Eject the memory card from the camcorder and
insert it into a card reader that is connected to a
computer.
2: Open [My Computer] or [Windows Explorer] and
double-click the removable disk icon that represents the memory card.
3: Copy images from the card into a directory of your choice on the
computer’s hard disk.
Connecting the Camcorder to a PC with the USB Cable
1: Connect the supplied USB cable to the computer's USB port and turn on
32
the camcorder. A message “Mass storage” or “PC Camera” appears on the
screen when connection to the computer has been successfully completed.
Press the OK button to set the camcorder to “Mass storage” mode.
2: Open [My Computer] or [Windows Explorer]. A "Removable Disk"
appears in the drive list. Double-click the "Removable Disk" icon to view its
contents. Files stored on the camera are located in the folder named
"DCIM". 3: Copy the photos or files to your computer.

7. Software Installation

Installing the Software

The bundled software CD has the drivers and software that come with
video camera.
Insert the CD into your CD-ROM drive. The autorun menu appears:
33
The following software is listed:
Install Driver: Installs software for PC camera
Arcsoft Mediaimpression: Installs software for editing movie clips and
photos.
Click the items in the autorun menu to install the software.
If the autorun menu does not appear automatically, open the CD-ROM in
[My Computer] or [Windows Explorer] and double-click the file named
[autorun.exe] to start the program. You can also click [Run] in the Windows
Startup menu, enter "D:\autorun.exe" (where D is your CD-ROM drive letter)
in the text box, and click [OK].

Install Driver

(1 )Insert the CD to ll the driver;
your PC,Click “Install Driver” to insta
34
(2)Click “Next” and then click “Install” to install the driver;
(3) Click “Finish” to complete the inst lation
al
35
(4) Connect the camcorder to PC by the USB-cable,then Power on;
(5) er to [PC Camera] mode.
Use the OK button to set the camcord
(6) d ware” appears;
An interface “Installing device river soft
(7) Select “Install the software automatically (Recommended)”;
(8) If “Your devices are ready to use” interface appears , The inst
finished and now you can use the PC-Camera function.
is
36
allation
How to use the PC Camera function
1. Power ON, connect the camcorder with the PC by USB-cable.
. Press the OK button to set the camcorder to PC Camera mode.
2
. Double click the icon “My Computer” (on the PC-desktop).
3
. Double click the icon
4
Then you can start to use the PC-Cam
era function.

8. Troubleshooting

Power does not turn on.
1.Battery is insufficie er
on.
The camcorder does not take pictures.
1.Memory is full.
nt to pow
Recharge the battery.
Insert a new memory card.
2.Memory card is not formatted
correctly.
Format the memory card again
37
or use a new card.
Im is blurry or out of focus. age
1.The camcorder was moving
when the image was captured.
Image is not displayed on the LCD monitor.
1. card with non-PICT
A memory
images (recorded with other
camera) is loaded.
Recorded files are not saved in memory.
1.
The camcorder was turned off
before the files are saved in
memory. appears
9. T
echnical Specifications
Sensor 5 Mega Pixel CMOS;
Hold the
when shooting picture.
ot display
This camcorder cann
non-PICT images.
ndicator
If the battery low i
recharge the battery
immediately.
camcorder steady
on the LCD monitor,
38
D o risplay 2.7” TFT C lo LCD Display
Foc f ty us Range 200cm ~ in ini
Ape F3.1, Fixed Frture ocus
Shutter Electronic Shutter: 1/2 ~ 1/1800 sec.
File Format
Resolution
Exposure Control Auto
White Balance scent / Auto / Daylight / Tungsten / Fluore
Self Timer 5 sec / 10 sec
Flash Mode uto Flash off / Flash on / Flash a
Storage Internal 32 MB
Storage External SD / MMC
TV System PAL / NTSC
Power Supply Lithium Battery
Sill Image: JPEG (EXIF 2.2 compatible)
AV Video: MP4 ; Audio: W
Still Image: 1600x1200 (2M) / 2592x1944
(5M), 3400x2550(8M)
4032x3024 (12M) by interpola
Video: 1280x720
39
by interpolation /
tion;
HD / 640x480 / 320x240
Operating Temperature to 40°C 0°C up
Storage Temperature -20°C up to +60°C
Microphone Built-in
Speaker included
Dimension Camera Body: 122 x 61 x 28 mm
Weight Camera Body w/o battery: approx. 85 g
www.mpmaneurope.com
40
Loading...