Moxa VPort 26A-1MP User’s Manual
Edition 2.1, December 2015
www.moxa.com/product
© 2015 Moxa Inc. All rights reserved.
Moxa VPort 26A-1MP User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2015 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expres sed or i mpl ied, incl uding, bu t not limit ed
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
+1-714-528-6777
Fax:
+1-714-528-6778
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia
-Pacific
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Before Getting Started
Before using your VPort 26A-1MP, please pay close attention to the following instructions:
After opening the VPort 26A-1MP box, compare the contents of the box with the Package Checklist in Chapter 1.
Notify your sales representative if any of the items are missing or damaged.
To prevent damage or problems caused by improper use, read the Quick Installation Guide (the printed handbook
included in the package) before assembling and operating the device and peripherals. You may also refer to Chapter
1, under Product Description, and all of Chapter 2, of this manual.
The VPort 26A-1MP IP Camera has been designed for various environments and can be used to build various
applications for general security or demonstration purposes. For standard applications, refer Chapter 2, Getting
Started, and Chapter 3, Accessing the VPort 26A-1MP Web-based Manager.
Important Note
Surveillance devices may be prohibited by law in your country. Since VPort is both a high performance surveillance
system and networked video server, verify that the operations of such devices are legal in your locality before
installing this unit for surveillance purpose s.
Table of Contents
1. Introduction ...................................................................................................................................... 1-1
Overview ........................................................................................................................................... 1-2
Package Checklist ............................................................................................................................... 1-4
Product Features ................................................................................................................................ 1-5
Typical Application .............................................................................................................................. 1-6
Product Description ............................................................................................................................. 1-7
2. Getting Started ................................................................................................................................. 2-1
Before Getting Started ........................................................................................................................ 2-2
First-Time Installation and Configuratio n ............................................................................................... 2-2
Hardware Installation ................................................................................................................... 2-2
Software Installation .................................................................................................................... 2-7
VPort 26A-1MP Dimensions .................................................................................................................. 2-9
Wiring Requirements ......................................................................................................................... 2-10
3. Accessing the VPort 26A-1MP’s Web-based Manager ........................................................................ 3-1
Functions Featured on the VPort’s Web H omepage .................................................................................. 3-2
VPort’s Information ..................................................................................................................... 3-2
IP Camera Name ......................................................................................................................... 3-2
Camera Image View .................................................................................................................... 3-2
Audio Control .............................................................................................................................. 3-3
Client Settings ............................................................................................................................ 3-3
System Configuration .................................................................................................................. 3-4
Video Information ....................................................................................................................... 3-4
Show PTZ Control Panel (only supported by non-onvif version firmware: V1.x) ................................... 3-4
Relay Control .............................................................................................................................. 3-4
Snapshot .................................................................................................................................... 3-4
4. System Configuration ........................................................................................................................ 4-1
System Configuration by Web Console .................................................................................................. 4-2
System ...................................................................................................................................... 4-3
General Settings .................................................................................................................. 4-3
Account Privileges ................................................................................................................ 4-4
Local Storage ...................................................................................................................... 4-5
System Log ......................................................................................................................... 4-6
System Parameters .............................................................................................................. 4-7
Firmware Upgrade ............................................................................................................... 4-8
Reset to Factory Default ....................................................................................................... 4-8
Reboot ............................................................................................................................... 4-8
Network ..................................................................................................................................... 4-9
General Network Sett ings ..................................................................................................... 4-9
SMTP Server and Email Account Settings .............................................................................. 4-14
Dynamic DNS .................................................................................................................... 4-15
Universal PnP .................................................................................................................... 4-15
QoS (ToS) ......................................................................................................................... 4-16
FTP Server Settings ............................................................................................................ 4-16
Multicast ........................................................................................................................... 4-17
Configuring Multicast Settings ............................................................................................. 4-18
HTTP Event Server ............................................................................................................. 4-19
Accessible IP List ............................................................................................................... 4-20
SNMP ............................................................................................................................... 4-21
Configuring SNMP Settings .................................................................................................. 4-21
SNMP Read/ Write Settings ................................................................................................. 4-22
HTTP Event Server ............................................................................................................. 4-23
ModBus/TCP ...................................................................................................................... 4-24
Telnet ............................................................................................................................... 4-25
LLDP ................................................................................................................................ 4-26
Video ....................................................................................................................................... 4-26
Image Settings .................................................................................................................. 4-26
Camera Setting ................................................................................................................. 4-27
ROI (Region of Interest) ..................................................................................................... 4-29
Privacy mask ..................................................................................................................... 4-30
Video Performance ............................................................................................................. 4-30
Audio ....................................................................................................................................... 4-33
Audio Source ..................................................................................................................... 4-33
PTZ ......................................................................................................................................... 4-33
Digital PTZ ........................................................................................................................ 4-33
DynaStreamTM ......................................................................................................................... 4-34
Basic ................................................................................................................................ 4-34
Conditions ......................................................................................................................... 4-35
Alarm ...................................................................................................................................... 4-35
System ............................................................................................................................. 4-35
Basic ................................................................................................................................ 4-36
Schedule ........................................................................................................................... 4-37
Event Alarm ...................................................................................................................... 4-38
Digital Input ...................................................................................................................... 4-39
Motion Detection ................................................................................................................ 4-40
CGI Event ......................................................................................................................... 4-43
Camera Tamper ................................................................................................................. 4-44
A. Frequently Asked Questions .............................................................................................................. A-1
B. Modbus Address Table ...................................................................................................................... B-1
Read/Write Registers (Support Function Code 4 & Funct ion Code 3) ........................................... B-1
C. Time Zone Table ................................................................................................................................ C-1
D. Technical Specifications .................................................................................................................... D-1
1
1. Introduction
The VPort 26A-1MP is a rugged IP camera designed for use in harsh environments. In addition to being able to
handle basic video feeds, many advanced features are also included to set up surveillance or web multimedia
applications. The VPort 26A-1MP is designed to provide stability, robustness, ease-of-use, and flexibility.
The following topics are covered in this chapter:
Overview
Package Checklist
Product Features
Typical Application
Product Description
Moxa VPort 26A-1MP Introduction
1-2
Overview
The VPort 26A-1MP is a vandal-proof, IP66-rated, fixed dome HD IP camera for use in harsh, outdoor
environments. With a maximum resolution of 1280 x 800, H.264/ MJPEG triple video streams and
day-and-night camera lens, the VPort 26A-1MP is especially well-suited for outdoor video surveillance
applications.
To enhance video image quality, the VPort 26A-1MP series is equipped with a megapixel 3 to 9 mm vari-focal
lens that meets versatile viewing angle and distance requirements. With a built-in removeable IR-cut filter, and
automatic switching from color to B/W images, the VPort 26A-1MP series is suitable for day-and-night use.
Along with built-in DNR (Digital Noise Reduction) and WDR (Wide Dynamic Range), the VPort 26A-1MP series
provides excellent image quality u n d er low illumination or back light conditions.
The VPort 26A-1MP series is specially designed for outdoor applications with the following features: IP66 rain
and dust protection, high EMI/surge protection, -40 to 50°C or -40 to 75°C operating temperature witho ut a
fan or heater, metal housing, and EN 62262 IK10 vandal-proof dome cover. In addition, the camera is built in
a dehumidified membrane for diffusing the moisture inside the camera.Users can choose either the VPort
P26A-1MP with PoE (Power over Ethernet, 802.3af) functionality, or the VPort 26A-1MP model with a 12/24
VDC or 24 VAC direct-wired power input.
The VPort 26A-1MP series is designed to pr ovide both H.264 and MJPEG vid e o streams and transmit up to 3
independent video streams (2 in H.264, and 1 in MJPEG) simultaneously. The camera can encode and transmit
up to 30 FPS for each of the H.264 and MJPEG streams. In addition, Moxa’s DynaStream™ function changes the
video frame rate automatically to help you control your network bandwidth budget and ease network system
management. The CBR Pro™ function guarantees no packet loss in limited bandwidth transmissions, ensuring
that images will not exhibit the mosaic effect. Advanced network security functions, such as 802.1x and SSH,
are also provided to prevent unauthorized access or data hij a cking, which is critical fo r most surveillance
applications.
High Quality 1/2.7” HD CMOS sensor with advanced DNR and WDR
The VPort 26A-1MP IP camera uses a 1/2.7” HD CMOS sensor with DNR (digital noise reduction) and WDR (wide
dynamic range), which provide clearer video images in many environments, and especially in low illumination
(lux) environments.
Comes with 3 to 9 mm vari-focal lens, to meet a variety of viewing
requirements
The VPort 26A-1MP IP camera is designed with a 3 to 9 mm vari-focal lens for providing viewing angles from
148.4° to 43.8° diagonal. In addition, this lens sup ports auto-iris functionality, and possesses day & night
capability with IR-cut removable (ICR), which is suitable for most outdoor applications.
-40 to 50°C or -40 to 75°C operating temperature without fan and heater
The VPort 26A-1MP IP camera can work in -40 to 50°C, and VPort 26A-1MP-T can work in -40 to 75°C
operating temperature range, without the need of fan and heater, which can reduces the maintenance
workload substantially, especially in the outdoor or harsh environments.
IP66-rated form factor design for protection against dust and rain
The IP66-rated form factor design makes the VPort 26A-1MP suitable for use in outdoor environments, without
the need for additional protective housing. In addition, cable glands are provided free of charge to ensure that
attached cables also have IP66-rated protection.
Support for PoE (Power-over-Ethernet) or direct-wired power inputs
The VPort P26 supports standard 48 VDC power-over-Ethernet (IEEE 802.3 af), and the VPort 26A-1MP
supports a direct-wired 12/24 VDC or 24 VAC power input.
High Performance H.264/MJPEG video compression
Video input can be efficiently compressed into H.264/MJPEG video strea m p a ckets in real time. This is done
without sacrificing remote monitoring capability or storage. Five le vels of compression quality and four different
image resolutions provide greater versatility.
Moxa VPort 26A-1MP Introduction
1-3
CBR Pro™ for no video image packet loss when bandwidth is limited
An innovative CBR Pro™ function, where CBR stands for constant bit rate, is provided with the VPort 26A-1MP
series for guaranteeing no video image packet loss when bandwidth is limited. Even when the general CBR
function is activated, there is a chance of video image packet loss, which could cause a mosaic effect due to a
burst of bandwidth consumption in a short time (few milliseconds) while delivering image frames. With Moxa
CBR Pro™, even video images of high-speed objects, such as cars, wil l exhibit good image quality with no
mosaic effect.
2-way audio supported for a complete surveillance solution
The VPort 26A-1MP series support bot h audio input and audio output for voice over IP communication between
a field site and central sit e. The 2-way audio function not only saves time, bu t also saves the cost of needing
to add additional communication devices (such as a phone).
Three video streams for meeting versatile application requirements
VPort 26A-1MP is a powerful IP Camera. Aside from the high quality H.264 video compression, it can also
generate a maximum of three video streams: two H.264 and one MJPEG simultaneously, to meet the needs of
specific applications. For example, the user can view the h.264 video streams with full D1 resolution at 30FPS,
do MJPEG image analysis with full D1 resolution at 10FPS, and record the H.264 video streams with CIF
resolution at 30FPS.
Video latency under 200 ms (milliseconds) for more real-time video
In some mission critical environmen ts, low video latency is a key requirement. For example, a highway
transportation system monitors vehicles that are moving very quickly. The video display in the traffic control
center needs to reflect actual current tra ffic conditions. Therefore, the video latency must be under 200ms.
SD Card for recording video locally when the network is down
The VPort 26A-1MP is equipped with an SD card socket (SDHC, V2.0) for local storage and offline data logging,
in the event of network interruptions. Currently, the VPort 26A-1MP supports SD cards up to 32 GB.
RTSP for easy integration with existing systems
RTSP (Real-time Streaming Protocol) is a client-server multimedia presentation control protocol, which ensures
interoperability among video devices and software. Hardware or software that supports RTSP streaming can
easily identify and decode the video stream without the hassle of codec installation. For example, users can
view video images from the VPort 26A-1MP directly with Quick Time and VLC, both of which support RTSP
streaming.
Multicast (IGMP) transmission for network efficiency
Transmitting digital video images via an IP network requires many times the bandwidth required for
transmitting general data. For this reason, the efficiency of network bandwidth management is one of the most
important factors that determine the performance of a video over I P su rveillance sys tem. The VP ort 26A-1MP
supports multicast transmission with the IGMP protocol, which can reduce the bandwidth requirements when
multiple clients access the same video stream, and greatly increases the ef ficiency of network bandwidth
management.
Easy web access using standard browsers
There is no need to install new software to access the IP camera, since the embedded web server allows users
to use any popular web browser to access the IP camera from anywhere over the Internet . As long as you are
connected to the network, you will be a b le to view the same images seen by your ca meras.
Built-in 3-area-selectable Video Motion Detection (VMD)
External sensors are not required, since the video image can be configured to detect motion in 3 areas, making
it easy to set up a security system either in your office or in the field. And the customizable settings allow you
to tune the system for both object size and sensitivity, making the IP Camera adaptable to different
environments.
Tamper alarm to detect when the camera has been painted or blocked
The tamper alarm helps prevent sabotage by detecting when the VPort 26A-1MP camera has been painted or
blocked.
Moxa VPort 26A-1MP Introduction
1-4
Weekly schedule for automated surveillance
The user-defined time period will check security settings on a weekly basis, and send notifications or drive
external devices, making the VPort 2 6A-1MP suitable for more versatile applications.
SDK support for developers
The high-performance IP camera can be integrated into many applications—without busting your budget—and
the complete programming interface of the Moxa VPort SDK PLUS makes the developer’s job easy and
straightforward. To ask about SDK requirements, please contact a Moxa sales representative for details and an
application form.
Package Checklist
The Moxa VPort 26A-1MP is shipped with the following items. If any of these items are missing or damaged,
please contact your sales representative for assistance.
• VPort 26A-1MP (includes 2-pin terminal block for power input) or VPort P26A-1MP (PoE power input)
• Screw handle accessory package
Torx screw driver for
attaching/detaching the
upper case
4 sets of self-tapping screws
(6 cm length) and anchors
9-pin terminal block for
DI/Relay/Audio
• Cable glands accessories package
IP66 cable glands to ensure IP66
protection when the cables are
connected
• Sticker for camera mounting positions
• Quick Installation Guide
• Document & Software CD (includes User’s Manual, Quick Installation Guide, and VPort Util ity)
• Warranty Statement
NOTE: Notify your sales representative if any of the above items are missing or damaged.
Moxa VPort 26A-1MP Introduction
1-5
Product Features
High Video Image Quality
• 1/2.7” progressive CMOS sensor for HD (1280 x 720) resolution
• Day and night viewing capability with ICR (IR cut filter) and color /black & white image switch
• Supports DNR (digital noise reduction), BLC (back level control), and WDR (wide dynamic range) for better
image quality
• Equipped with 3 mm to 9 mm vari-focal megapixel lens for wide-range fields of view
• Minimum illumination up to 0.2 lux (color) and 0.05 lux ( B/W) at F=1.2
• Image mirror and inverse
• 350° pan, 85° tilt, and 360° rotate camera head angles for different installation positions.
• Supports up to 3 privacy mask areas and 4X digital zoom
Excellent Video/Audio streaming and network transmission performance
• Up to 3 simultaneous video streams for H.264 and MJPEG codecs
• Video stream up to 30 frames/sec at WXGA (1280 x 800) resolution
• DynaStream™ supported for optimal network efficiency
• CBR Pro™ supported for high image quality in limited bandwidth transmissions
• Video latency under 200 ms
• 1 audio input and 1 audio output supported for complete video/audio surveillance solution
• WXGA/HD/SVGA/Full D1 / 4CIF/ VGA/ CIF/ QCIF resolution
• TCP, UDP, and HTTP network transmiss ion mo de
• Supports RTSP streaming
• Supports IGMP (ver.3) protocols for efficient network transmission
• Supports SNMP (V1/V2C/V3) for network system integration and management
• Supports QoS (ToS) for transmission priority
• Adjustable frame rate and bit rate control
• User-friendly IP filtering
• Supports IEEE802.1X for network access authenticatio ns
• Supports HTTPS and SSH for network transmission security
• UPnP Supported
• Up to 5 unicast video streams, and 50 multicast clients
• Supports multicast push for all multicast clients
• OnVIF standard supported for compatibility with other IP video products
• Modbus/TCP supported for direct communication with SCADA system
Rugged Design for Mission-critical Industrial Environments
• IP66 form factor protection for rain and dust
• Model available with PoE (802.3af) or 12/24 VDC and 24 VAC power input, with LED indicators
• Panel mounting for mounting on a ceiling, or outdoor installation kit for versatile installation method
• -40 to 50°C or -40 to 75°C (T model) operating temperature for critical industrial environments
• No heater or fan for long MTBF
• CE, FCC, UL60950-1
• 5-year product warranty
Intelligent Alarm Triggering Capability
• Built-in tamper alarm, and VMD (video motion detection)
• 1 DI and 1 relay output (DO) for sensors and alarms
• Supports video loss alarm
• Pre, trigger, and post snapshot images supported
Moxa VPort 26A-1MP Introduction
1-6
• 24 MB video buffer for pre-event snapshot images
• Sequential snapshot images supported
• Supports SDHC slot for local storage with SD card in event recording
• Supports SMTP and FTP for alarm message transmission
• Supports HTTP event server
Video management and control
• Support for Moxa SoftNVR-IA IP surveillance software, a video recording and management solution
• Free: Moxa VPort SDK Plus with CGI Commands, ActiveX Control, and API support for third-party
developers
• ONVIF conformity for standardization and interoperability
NOTE
If you are interested in Moxa’s VPORT SDK PLUS, please go to Moxa’s website
www.moxa.com
to download the
package, or contact a Moxa sales representative for more information about this SDK
NOTE
If you are interested in SoftNVR
-IA IP surveillance software, please go to Moxa’s website (www.moxa.
com) to
download the trial version.
Typical Application
Moxa VPort 26A-1MP Introduction
1-7
Product Description
Form Factor
IP Camera Module
Moxa VPort 26A-1MP Introduction
1-8
Vari-focal Lens
The VPort 26A-1MP series comes with a day and night 3to 9mm megapixel lens for providing high quality video
images. Users can adjust the Zoom and Focus manually to get clear images regardless of the site environment.
NOTE
To tune the focus position, loosen the screw, and then turn the
lens head.
Pan, Rotation and Tilt Adjustment
Use the pan, rotation and tilt fasteners for panning, rotating and tilting the lens angles. To do this, the screws
must be loosened in advance. After the lens angles are correct, tighten the screws to fix the angles.
Light Sensor
The VPort 26A-1MP includes a light sensor for detecting illumination, which is for enabling the ICR (IR-cut filter
removable) function. When the illumination is under 3 lux, the image wil l be switched to night mode in black
and white, and when the illumination is greater than 5 lux, the image will be switched back to day mode in
color.
2-pin Terminal Blocks for Power Input
VPort 26A
-1MP series has comes in two models:
VPort 26A-1MP: 12/24 VDC or 24 VAC power inputs
VPort P26A-1MP: powered with PoE (Power over E thernet, 802.3af)
Note: The 2
-pin terminal block shown here is for the direct-
wired power input of
the VPort 26A
-1MP.
NOTE
The specifications of the direct
-wire power input are 12-32 VDC for 12/24 VDC power input, or 18-
30 VAC for
24 VAC power input. The maximum power consumption is
4.7 Watt.
Moxa VPort 26A-1MP Introduction
1-9
9-pin Terminal Block Connector for DI, DO, and Audio
The VPort 26A-1MP supports 1 DI (digital input), 1 DO (relay output), 1 audio input (line-in or mic-in), and 1
audio output (line-out) through the 9-pin terminal block.
DO
(Relay Output)
NO (Normal Open)
Max. 1A, 24 VDC
Initial status is Normal Open
C (Common)
NC (Normal Close)
DI (Digital Input)
+
Low: +13V to +30V
High: -30V to +3V
-
LED Indicators and DIP Switches
The VPort
26A-1MP has 3 LEDs for indicating the pow er status, 10/100 Mbps Ethernet
link, and system status. In addition, one DIP switch (No.2) is provided for enabling or
disabling the LED light for users who do not want the LED lig ht to be visible at night.
LED Description
Power On: power on
Off: power off
10/100 M Amber: Ethernet link is 10 Mbps
Green: Ethernet link is 100Mbps
System Red On Hardware initialization
Red blinking Software initialization
Green On System boot-up successfully
Green blinking Firmware upgrade proceeding
DIP Switch 1 Reserved
DIP Switch 2 On: LED light is on
Off: LED light is off
SD card Socket (SDHC)
The VPort 26A-1MP supports a standard SDHC interface for loc al storage with a current maximum size of 32 GB.
The user can use an SD card which is fits this specification. Currently, the local storage supports triggered video
recording when an event has occurred.
Moxa VPort 26A-1MP Introduction
1-10
NOTE
The VPort 26A
-1MP supports a s
tandard SDHC interface. Users can use SD cards suitable for this specification.
Transcend or Sandisk SD cards are recommended, particularly Sandisk Extreme III SD, because of their rapid
read/write speed.
NOTE
To check if the SD card has been successfully mounted, access the VPort’s web
-based manager and check
under system configuration
-> Local storage.
Reset Button
The reset button is used to reset the camera hardware.
1. Reboot:
To reboot the VPort 26A-1MP, power it off and then power it back on again, or push the RESET button one time.
The System LED will light in red as the POST (Power on Self Test) process runs. When the rebooting process is
finished, the System LED will change to a green color.
2. Restore to Factory Settings:
To restore the VPort 26A-1MP to the factory default settings, press the reset button continuously until the
System LED blinks in red. After the system LED stops blinking, release the reset button. The POST process will
run, and the VPort will reboot. The System LED will light in green when the VPort has finished rebooting.
RJ45 Ethernet Port
The RJ45 Ethernet port is for 10/100Mbps network transmission, in addition to PoE (power over Ethernet,
802.3af) power supply for VPort P26A.
NOTE
The VPort P26 supports standard IEEE 802.3af Power
-over-Ethernet (PoE). T
he maximum power consumption
is about
5.8W.
NOTE
The equipment is designed for in building installation only and is not intended to be connected to exposed
(outside
plant) networks.
2
2. Getting Started
This chapter includes information about how to install a VPort 26A-1MP IP camera.
The following topics are covered in this chapter:
Before Getting Started
First-Time Installation and Configuration
Hardware Installation
Software Installation
VPort 26A-1MP Dimensions
Wiring Requirements
Moxa VPort 26A-1MP Getting Started
2-2
Before Getting Started
In what follows, “user” refers to those who can access the IP camera, and “administrator” refers to the person
who knows the root password that allows changes to the IP camera’s configuration, in addition to providing
general access. Administrators should read this part of the manual carefully, especially during installation.
First-Time Installation and Configuration
Hardware Installation
Step 1: Open and remove the upper case.
Use the security Torx to loosen the upper case screws.
Step 2: Remove the inner case
Loosen 4 screws, and take out the IP camera module.
Moxa VPort 26A-1MP Getting Started
2-3
Step 3: Connect the cables.
a) Open the conduit hole. (use the side conduit hole as example)
b) Prepare the cable gland (if required).
c) Use the cable gland to assemble the cables.
NOTE
When
installing the cable gland, make sur e the 2 rubber rings are assembled properly for IP66 protection. If
necessary, use silicon sealant.
Moxa VPort 26A-1MP Getting Started
2-4
d) Connect the cables to the I P ca m e r a m od u l e’s connectors.
Connect the Ethernet cable to RJ45 Ethernet port, as well as the terminal blocks with power line and
DI/DO/Audio lines (if used).
NOTE
Be sure to arrange the cables carefully to make sure that all cables are connected p r operly. We recommend
connecting the Ethernet cable first, and then the 9
-pin terminal block. Connect the 2-pin terminal block last.
NOTE
The conduit hole must face downward to provide the VPort 26A
-1MP with IP66 protection against rain when
installed in an outdoor environment.
Moxa VPort 26A-1MP Getting Started
2-5
Step 4: Mount the bottom case on the ceiling or accessory’s mounting kit
(VP-MK2)
a) Mounting on the ceiling
Step 1:
Use the installation stick or attach th e b ottom case to the appropriate mounting location on the
wall, and mark the positions of the four screw holes with a pen or a pencil.
Step 2:
In
the marked locations, drill a hole slig htly smaller than the supplied screw anchors.
Step 3:
Put anchors into these drilled holes.
Step 4:
Fasten the
bottom case with the four self-tap screws.
b) Mounting on the accessory’s mounting kit (VP-MK2)
Step
1:
Fasten the bottom case on the plate with the four machine screws, which are provided in VP-MK2’s
accessory package.
Step 2:
Assemble the mounting kit with the se lected accessory.
VPort 26A-1MP + VP-MK2 + VP-520L VPort 26A-1MP + VP-MK2 + VP-520HB
NOTE
Choose the appropriate mounting accessories based on the installation requirements.
Moxa VPort 26A-1MP Getting Started
2-6
Step 5: Assemble the IP Camera Module with the bottom case.
Step 6: To get the desired video image, adjust the angles and zoom strength.
a) Pan adjustment
b) Tilt adjustment
c) Rotate adjustment
NOTE
Do not grasp the lens when rotating the camera. Instead, hold
the two copper cylinders.
Moxa VPort 26A-1MP Getting Started
2-7
NOTE
After adjusting the PAN, TILT, and ROTATE positions, tighten all
of the screws to ensure that the
orientation of
the camera does
not change.
d) Zoom adjustment
To adjust the Zoom and Focus positions, connect to the camera’s web console first so that you can view a live
video feed. Next, loosen the screws for both the zoom and focus positions, and then rotate the lens to focus on
the desired image. Finally, tighten both screws.
NOTE
To adjust the focus position, loosen the appropriate screw and
then rotate the lens head.
Step 7: Fasten the upper case to the bottom case to complete the hardware
installation.
Software Installation
Step 1: Configure the VPort 26A-1MP’s IP address
When the VPort 26A-1MP is first powered on, the POST (Power On Self Test) will run for a few moments. The
System LED will turn green when the POST is complete. The 10 Mbps or 100 Mbps LED will then flash as the IP
address is assigned. The network env ir onment determines how the IP addr ess is assigned.
Network Environment with DHCP Server
For this network environment, the unit’s IP address will be assigned by the network’s DHCP server. Refer to the
DHCP server’s IP address table to determine the unit’s assigned IP address. You may also use the Moxa VPort
and Ether Device Configurator Utility (edscfgui.exe), as described below:
Using the Moxa VPort and EtherDevice Configuration Utility (edscfgui.exe)
1. Run the edscfgui.exe program to search for the VPort device. After the application window opens, click on
the Search button to initiate a search.
2. When the search has concluded, the VPort’s Model Name, MAC address, IP address, serial port, and HTTP
port should be listed in the utility’s window.
Moxa VPort 26A-1MP Getting Started
2-8
3. Users can double click the selected VPort, or use the IE web browser to access the VPort’s web-based
manager (web server).
Manual Address Assignment
If your VPort 26A-1MP is connected to a network that does not have a DHCP server, then you will need to
configure the IP address manually. The default IP address of the VPort 26A-1MP is 192.168.127.100 and the
default subnet mask is 255.255.255.0. Note that you may need to change your computer’s IP address and
subnet mask so that the computer is on the same subnet as the VPort.
To change the IP address of the VPort manually, a ccess the VPort’s web server and navigate the System
Configuration Network General page to configure the IP address and other network settings. Toggle
the Use fixed IP address to ensure that the IP address you assign is not deleted each time the VPort is
restarted.
Step 2: Accessing the VPort 26A-1MP’s web-based manager
Type the IP address in the web browser’s address input box and then press enter.
Step 3: Install the ActiveX Control Plug-in
A security warning message will appear the first time you access the VPort’s web-based manager. The message
is related to installing the VPort AcitveX Control component on your PC or notebook. Click Yes to install this
plug-in to enable viewing of video images over the IE web browser.
NOTE
For Windows XP SP2 systems or later, the ActiveX Control component will be blocked for system security
reasons. In this case, the VPort’s security warning message window may not appear. Users should access the
operating system control panel to unblock ActiveX controls or d isable t he se curit y c onfigurati on to enable the
installation of the VPort’s ActiveX Control component .
Step 4: Access the VPort 26A-1MP’s web-based manager.
After installing the ActiveX Control component, enter the IP address of the VPort device to access its web-based
controls; they should imme diately appear. Check the following items to make sure the syst em was installed
properly:
1. Video Images
2. Audio Sound (make sure your PC’s or notebook’s sound is turned on)
3. Video Information
Moxa VPort 26A-1MP Getting Started
2-9
Step 5: Access the VPort system configuration.
Click on System Configuration to display a system overview. The Model Name, Server Name, IP Address,
MAC Address and Firmware Version will appear in the green bar at the top of the page. Use this information
to review the installation details.
For details about configuration settings, check the User’s Manual on the software CD.
NOTE
After accessing the VPort 26A
-1MP’s web-based manager, administra tors sho u ld acce ss System
Configuration
System Account
to set up the administrator’s password and enable the authentication
function. The administra tor account name is admin.
An authentic
ation window will pop up requesting the account name and password each time the VPort 26A-
1MP
is accessed.
VPort 26A-1MP Dimensions
(Unit=mm)
Moxa VPort 26A-1MP Getting Started
2-10
Wiring Requirements
ATTENTION
Be sure to disconnect the power cord before
installing and/or wiring your Moxa VPort 26A-1MP.
Calculate the maximum possible current in each power wire and common wir e. O bserve all electrical codes
dictating the maximum current allowable for each wire size.
If the current goes above the maximum rati
ngs, the wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following:
• Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. To avoid
interference, wires with different signal characteristics should be routed separately.
• You can use the type of signal transmitted through a wire to determine which wires should be kept separate.
The rule of thumb is that wiring that shar es similar electrical characteristics can be bundled together.
• Keep input wiring and output wiring separate.
• It is strongly advised that you label wiring to all devices in the system w hen necessary.
WARNING
This equipment is intended to be used in a Restricted Access Location.
3
3. Accessing the VPort 26A-1MP’s
Web-based Manager
This chapter includes information ab out how to access the VPort 26A-1MP IP camera for the first time.
The following topics are covered in this chapter:
Functions Featured on the VPort’s Web Homepage
VPort’s Information
IP Camera Name
Camera Image View
Audio Control
Client Settings
System Configuration
Video Information
Show PTZ Control Panel (only supported by non-onvif version firmware: V1.x)
Relay Control
Snapshot
Moxa VPort 26A-1MP Accessing the VPort 26A-1MP’s Web-based Manager
3-2
Functions Featured on the VPort’s Web
Homepage
The homepage of the VPort’s web conso le shows information specific to tha t VPort, the camera image, and
configurations for the client and server.
NOTE
The VPort’s web homepage is best viewed in 1280 x 1024 screen resolution. This is because the camera image
can be viewed at a resolution up to
HD (1280x800
). We strongly recommend using IE 6.0 (Microsoft Internet
Explorer) or above to avoid incompatibility with the ActiveX Plug
-in.
VPort’s Information
This section shows the VPort’s model name, server name, IP address, MAC add ress and firmware version.
IP Camera Name
A server name can be assigned to each ser ver. Administrators can change the name in System
Configuration/System/General. The maximum length of the sever name is 40 bytes.
Camera Image View
The assigned image description and system date/time will be displayed in the caption above the image window.
You may disable the caption or change the location of the image information in System
Configuration/Video/Image Set t ing. Note that if the VPort’s motion detection functio n is active, some
windows in the video picture might be framed in red.
Moxa VPort 26A-1MP Accessing the VPort 26A-1MP’s Web-based Manager
3-3
Audio Control
The VPort 26A-1MP provides both audio input and audio output for voice over IP communication. Client users
can directly enable and disable the audio input (a microphone, for example) by checking the box of Enable
Audio Post on the VPort’s web homepage. You may also use the Client Setting to disable the audio
transmission.
Client Settings
Users can configure the following functions in Client Settings.
1. Encode standard: Shows the encoding algorithm currently being used. VPort 26A-1MP features built-in 2
encode engine to generate a maximum of three simultaneous video streams. Ea ch client can select the
H.264 video streams from Stream 1, or the MJPEG/ H,264 video stream from Stream 2. To con figure these
video streams, please go to:
System Configuration/Video/Video Performance.
2. Protocol Options: Choose one of four protocols to optimize your usage—Multicast (RTSP or Pus h) or
Unicast (UDP, TCP, HTTP).
• Multicast protocol can be used to send a single video stream to multiple clients. In this case, a lot of
bandwidth can be saved since only one video stream is transmitted over the network. However, the
network gateway (e.g., a switch) must support the multicast protocol (e.g., IGMP snooping). Otherwise,
the multicast video transmission will not be successful.
RTSP: Enable the multicast video stream to be sent in RTSP control, which means the multicast
video stream will be sent only it receives the client’s reque st.
Push: Enable the multicast video stream to be sent in Push control, which means that after this
setting is selected the multicast video stream will be sent continuously even without any client
request.
• Unicast protocol is used to send a single video stream to one client.
UDP can be used to produce audio and video streams that are more real-time. Ho wever, some
packets may be lost due to network burst traffic, and images may become blurred.
TCP can be used to prevent packet loss, whic h results in a more accurate video display. The
downside of using TCP is that the real-time delay is worse than with UDP protocol.
HTTP can be used to prevent being blocked by a router’s firewall. The downside of using HTTP is
that the real-time delay is worse than with UDP protocol.
• Network Interface designates the connection interface for multicast video streams selection. The box
lists the current NIC interfaces. Select which NIC interface will receive multicast streams.
Once the IP camera is connected successfully, Protocol Options will indicate the selected protocol. The selected
protocol will be stored on the user’s PC, a nd will be used for the next connection.
NOTE
For multicast video stream settings, please re
fer to System Configuration Network Multicast.
Moxa VPort 26A-1MP Accessing the VPort 26A-1MP’s Web-based Manager
3-4
System Configuration
A button or text link on the left side of the system configuration window only appears on the administrator’s
main page. For detailed system configuration instructions, refer to Chapter 4, Syst em Configuration.
Video Information
Users can easily monitor the current video performance by looking at the Video Information shown on the
left side of the homepage. The following properties are shown : Stream, Video Size, Video Quality (Fixed bit rate
or Fixed video quality), Max. FPS (frames per second), and (current) FPS Status. Users can select the target
camera image to view each camera’s video performance.
Show PTZ Control Panel (only supported by non-onvif version
firmware: V1.x)
The VPort 26A-1MP seires supports a maximum 4X digital zoom. The user can control the PAN, TILT, ZOOM on
this PTZ control panel.
Relay Control
The VPort 26A-1MP series has 1 relay output for external devices, such as alarms. Administrators and
permitted users can click on Open to short the Common and Normal Open digital output pins, or click on Close
to short the Common and Norma l Close digital output pins .
Snapshot
Users can take snapshot images for storing, printing, or editing by clicking the Take button. Save the image by
rick-clicking and selecting Save.
4
4. System Configuration
After installing the hardware, the next step is to configure the VPort 26A-1MP’s settings. Users can configure by
web console.
The following topics are covered in this chapter:
System Configuration by Web Console
System
Network
Video
Audio
PTZ
DynaStreamTM
Alarm
Moxa VPort 26A-1MP System Configuration
4-2
System Configuration by Web Console
System configuration can be done re motely with Internet Explorer. To acc ess the server, type the system
configuration URL, http://<IP address of Video Server>/overview.asp, to open the configuration main
page.
There are six configuration categories: System, Network, DynaStream, Video, Audio, and Alarm. A
description of each configuration item is shown in the tabl e below :
Category Item Description and Contents
System
General Set Host Name and Date/Time
Accounts Administrator, User, and Demo Account Privileges Management
Local Storage Configure the local storage settings
Diagnosis Self-diagnostic report with system, communication, power, and LED
status
System Log System Log and operation information
System Parameter System parameter information and Import/Export functions
Firmware Upgrade Remote Firmware Upgrade
Factory Default Reset to Factory Default
Reboot Device will reboot for restarting system
Network
General The IP network settings of this VPort
SMTP Server Set up Primary and Secondary SMTP Server and e-mail accounts
FTP Server Set up the Primary and Secondary FTP Server
DDNS Configure Dynamic DNS service
UPnP Enable UPnP function
Multicast Setting Set up Multicast (IGMP) Streaming
Accessible IP Set up a list to control the access permissio n o f clients by IP address
SNMP Configure the SNMP settings
ToS Configure ToS (Type of Service)
HTTP Event Server Set up the HTTP Event Server to send the event alarm action
Modbus/ TCP Enable Modbus/TCP function
IEEE 802.1X Configure IEEE 802.1X functi o n
Telnet Configure Telnet
LLDP Configure LLDP
Video
Image Settings
Configure the information of video image
Camera Setting
Configure the attributes of video image
ROI
Configure the ROI(region of interest) settings
Privacy Mask
Configure the Privacy Mask settings
Video Performance
Set up the Encode Standard(MJPEG or H.264), Size (Resolution), FPS and V ideo
Quality
Audio Audio Setting Configure the Audio Source
PTZ Digital PTZ Configure the Digital PTZ settin gs
DynaStrea
m
Basic
setup the video frame rate change once an alarm or event is triggered
Conditions setup the event/ alarm to trigger the Dynastream, and the behavior
after being triggered
Alarm
System General settings of alarm
Basic Basic settings of event alarm
Schedule Schedule setting of event alarm
Event
Alarm
Digital input Configure the Digital Input Alarm
Motion
Detection
Configure the motion detection alarm
CGI Event Set up the CGI event alarm
Camera
Tamper
Configure the camera tamper alarm
Moxa VPort 26A-1MP System Configuration
4-3
This table can also be found on the System Configuration Overview webpage.
System
General Settings
On the General Settings page, administrators can set up the video Server name and the Date and Time,
which is displayed in the image’s caption.
Server name
Setting Description Default
Max. 40 characters Use a different server name for each server to help identify the
different servers. The name appears on the web homepage.
VPort 26A-1MP IP
camera
Moxa VPort 26A-1MP System Configuration
4-4
Server Contact
Setting Description Default
Max. 40 characters Edit the responsible operator for this camera server Blank
Server Location
Setting Description Default
Max. 40 characters Edit the location of this camera server Blank
Date and Time
Setting Description Default
Keep current date and
time
Use the current date and time as the VPor t’s time setting. Keep current date
and time
Sync with computer
UTC time
Synchronize VPort’s data and time setting with the local
computer time.
Manual Manually change VPort’s date and time setting.
Automatic
Use the NTP server for changing VPort’s date and time setting
in a given period.
NOTE
Select the
Automatic option to force the VPort to synchronize automatically with timeservers over the
Internet. However, synchronization may fail if the assigned
NTP server cannot be reached, or the VPort is
connected to a local network. Leaving the
NTP server blank will force the VPort to connect to default
timeservers. Enter either the Domain name or IP address format of the timeserver if the DNS server is
available.
2 NTP servers may be set as backups, and update intervals can be configured from a minimum of 15 minutes
to a maximum of one month.
Don
’t forget to set the time zone in local settings. Refer to Appendix G for your region’s time zone.
Account Privileges
Different account privileges are available for different purposes.
Moxa VPort 26A-1MP System Configuration
4-5
Admin password
Setting Description Default
Admin Password (8 to
15 characters)
The administrator can type the new password in this box. Default admin
password is “admin”
Confirm Password (8 to
15 characters)
If a new password is typed in the Admin Password box, you
will need to retype the password in the C on firm Password
box before updating the new password.
NOTE
The default account name for administrator is
admin; the administrator account name cannot be
changed.
User’s Privileges
VPort products provide 10 user accounts for accessing the VPort.
Setting Description Default
User Name Type a specific user name for user authentication. None
Password Type a specific password for user authentication.
Privilege Check the function boxes to assign privileges for users in
Control Relay1
NOTE
The FPS of the video stream will be reduced as more and more users access the sa me VPort. Currently, the
VPort 26A
-1MP is only allowed to send 5 unicast video streams. Therefore, limit the number of users
simultaneously accessing a VPort 26A
-1MP to prevent performance problems.
Local Storage
The VPort 26A-1MP supports an SD card slot (SDHC interface) for recording video when preconfigured events
(alarms) occur. Administrators can down load these recorded videos via FTP, or remove the SD card and directly
copy the files via a card reader.
Local Video Recording Setting
Setting Description Default
Enable video recording
once there is an
event/alarm
Enable the video recording action once there is an event/alarm Enable
Moxa VPort 26A-1MP System Configuration
4-6
Recording Stream
Setting Description Default
Stream 2: H.264 or
Stream 2: MJPEG
Select the H.264 or MJPEG of stream 2 for video recording Stream 2: MJPEG
FTP Daemon
Setting Description Default
Enable FTP daemon Enable the FTP service for downloading the recorded video files
by the administrator
Enable
Server Port The FTP s er ver port number 21
SD card
Setting Description Default
Reboot the system
when the SD card fails
to mount
This function can reboot the system when the SD card mount
fails to re-detect the SD mount.
Enable
NOTE
The recorded videos will be stored in the “/VPortfolder” folder. Eac h recorded file is 10 seconds of vi deo. These
are AVI files for playback in a popular media player.
NOTE
Due to file system limitations, the maximum number of files is 16584. When the number of files in the SD card
is up to 16584, or the free space is under 100MB, the system will start to delete the oldest files.
System Log
The system log contains useful information, including current system configuration and activity history with
timestamps for tracking. Administrators can save this information in a file (system.log) by clicking the Export
to a File button, or send the file by email by clicking the Send a Report via Email button. In addition, the log
can also be sent to a Log Server for backup. The administrator can set up the Syslog Server 1 and Syslog
server 2 below the system log list.
Moxa VPort 26A-1MP System Configuration
4-7
Send to system log server
Setting Description Default
Send to system log
server
Enables sending the system log to the log sever. Disable
Syslog Sever 1 The address of the first system log server. Blank
Port Destination The port number of first system log server. 514
Syslog Sever 2 The address of the second system log server. Blank
Port Destination The port number of second system log server. 514
NOTE
A maximum of 500 lines is displayed in the log. Earlier data beyond the first 500 entries are still in the VPort’s
database; the adm
inistrator can export the m a t a n y time.
System Parameters
The System Parameters page allows you to view all system pa rameters, which are listed by category. The
content is the same as the VPort’s sy s _config.ini file. Administrators can also sa ve this information i n a file
(sys_config.ini) by clicking the Export to a File button, or import a file by clicking the Browse button to search
for a sys_config.ini file and then clicking the Import a System Parameter File button to update the system
configuration quickly.
NOTE
The system parameter import/export functions allow the administrator to backup and restore system
configurations. The Administrator can export this sys_config.ini file (i n a special binary format) for backup, and
import the sys_config.ini file to restore the system configurations of VPort IP cameras. System configuration
changes will take effect after the VPort is rebooted.
Moxa VPort 26A-1MP System Configuration
4-8
Firmware Upgrade
Take the following steps to upgrade the firmware:
Step 1:
Press the
Browse button to select the firmware file.
NOTE
For the VPort 26A
-1MP, the firmware file extension shou ld be .rom.
Step 2:
Click on the
Upgrade button to upload the firmware to the VPort.
Step 3:
The system will start to run the firmware upgrade process.
Step 4:
Once
Firmware Update Success…..Reboot.... is displayed, please wait f or few seconds for the
VPort to reboot. The reboot process is f inished once the
STAT LED is lit continuous ly in gr een .
NOTE
Upgrading the firmware will not change the original settings.
Reset to Factory Default
From the “Reset to Factory Default” page, click on OK (as shown in the following figure) to reset the VPort to
its factory default settings.
NOTE
All parameters will be reset to factory defaults when you use the F actory Default function. For this reason, if you
want to keep a digital copy of the current configuration, remember to export the sys_config.ini file before using
the Factory Default function.
Reboot
From the “Device Reboot” page, click OK (as shown in the following figure) to restart the VPort’s system.
Moxa VPort 26A-1MP System Configuration
4-9
Network
General Network Settings
The General Network Settings page includes some basic but important network configurations that enable
the VPort to be connected to a TCP/IP network.
Access Method
VPort products support the DHCP protocol, which means that the VPort can get its IP address from a DHCP
server automatically when it is connected to a TCP/IP network. The Administrator should dete rmine if it is more
appropriate to use DHCP, or assign a fixed IP.
Setting Description Default
DHCP Get the IP address automatically from the DHCP server. DHCP
DHCP + Auto configure
Get the IP address automatically from the DHCP server, and
download the configurations from the TFTP server with Opt
66/67 mechanism.
Use fixed IP address Use the IP address assigned by the administrator.
NOTE
We strongly recommend that the administrator assign a fixed IP address to the VPort, since all of the functions
and applications provided by the VPort are active when the VPort
is connected to the network. Use DHCP to
determine if the VPort’s IP address may change when then network environment changes, or the IP address is
occupied by other clients.
Moxa VPort 26A-1MP System Configuration
4-10
Auto Configuration
In a mass installation, it is time consuming to configure each of the many devices one by one. Therefore, DHCP
Opt 66/67 provides a mechanism whereby configurations can be saved on a TFTP server. Once a new device is
installed, the configurations can be downloaded to this new device automatically. By doing this, the installer
can save a lot of time and efforts in mass devic e installation. Follow the steps below to use the
auto-configuration function via Opt 66/67.
Step 1:
When VPort 26A-1MP enables t he auto-conf iguration function, it will ask for the IP address from DHCP server,
and the path of the TFTP server and configuration file.
Step 2:
Once VPort 26A-1MP completes the IP settings, it will acquire the configuration file from the TFTP server, and
check if this configuration file is right or not.
NOTE
For
auto-configuration to work properly, the system should:
Have a DHCP Server that supports DHCP Opt 66/67 in the network switches and routers.
Have a TFTP server that supports the TFTP protocol
Moxa VPort 26A-1MP System Configuration
4-11
General Settings
Setting Description Default
IP address
Variable IP assigned automatically by the DHCP server, or fixed
IP assigned by the Administrator.
192.168.127.100
Subnet mask Variable subnet mask assigned automatically by the DHCP
server, or a fixed subnet mask assigned by the Administrator.
255.255.255.0
Gateway
Assigned automatically by the DHCP server, or assigned by the
Administrator.
Blank
Primary DNS
Enter the IP address of the DNS Server used by your network.
After entering the DNS Server’s IP address, you can input the
VPort’s url (e.g.,
www.VPort.company.com) in your browser’s
address field, instead of entering the IP address.
Obtained
automatically from
the DHCP server, or
left blank in
non-DHCP
environments.
Secondary DNS Enter the IP a
ddress of the DNS Server used by your network.
The VPort will try to locate the secondary DNS Server if the
primary DNS Server fails to connect.
Obtained
automatically from
the DHCP server, or
left blank in
non-DHCP
environments.
HTTP
Setting Description Default
HTTP Port
(80, or 1024
to 65535)
HTTP port enables connecting the VPo rt to the web. 80
HTTPS port (80, or
1024 to 65535)
HTTPS port number for communication encryption (do not set
the same port number as the HTTP port)
443
HTTP mode Select the HTTP transmission mode: HTTP Only or HTTP +
HTTPS
HTTP Only
RTSP Streaming
The VPort 26A-1MP supports standard RTSP (Real Time Streaming Protocol) streaming, which means that all
devices and software that support RTSP can directly acquire and view th e v ideo images sent from the VPort
26A-1MP without any proprietary codec or SDK installations. This makes network system integration much
more convenient. For different connection types, the access name is different. For UDP and TCP streams, the
access name is udpStream. For HTTP stre ams, the access name is moxa-cgi/udpstream_ch<channel
number>. For multicast streams, the access name is multicastStream_ch<channel number>. You can
access the media through the follow ing URL: rtsp://<IP address>:<RTSP port>/<Access name> for
software that supports RTSP.
Setting Description Default
RTSP Port An RTSP port is similar to an HTTP port, which can enab le the
connection of video/audio streams by RTSP.
554
Moxa VPort 26A-1MP System Configuration
4-12
The VLC media player is used here as an example of a RTSP streaming application:
Step 1:
Open
VLC Player and select Media - Open network streaming
Step 2:
When the following pop
-up window appears, type the URL in the input box. E.g., type
rtsp://<VPort’s IP address>[:<RTSP Port]/udpstream_ch1_stream< 1 o
r 2>
rtsp://<VPort’s IP address>[:<RTSP Port]/multicaststream_ ch1_stream<1 or
2>
RTSP Port: 554
Is default, and then click on OK to connect to the VPort P06-1MP-M12.
Moxa VPort 26A-1MP System Configuration
4-13
Step 3:
Wait a few seconds for
VLC Player to establish the connecti on.
Step 4:
After the connection has been established, the VPort’s video will appear in the
VLC Player display
window.
NOTE
The video performance of the VPort
IP camera
may vary when using other media players. For example, you will
notice a greater delay when viewing the VPort’s video from the VLC player compared t o viewing it directly from
the VPort’s built
-in web server. In addition, viewing the VPort’s video from the
VLC player through a router or
Internet gateway could result in a broken connection.
NOTE
For the time being, the VPort’s RTSP video/audio stream can be identified and viewed by Apple QuickTime Ver.
6.5 and above, and the VLC media player. System integrators can use these 2 media players to view the VPort’s
video directly, without needing to use the VPort’s S DK to create customiz
ed software.
NOTE
When using RTSP, the video stream format should be H.264 o r MPEG4. MJPEG does not support RTSP.
Moxa VPort 26A-1MP System Configuration
4-14
SMTP Server and Email Account Settings
The VPort not only plays the role of a server, but can also connect to outside servers to send alarm messages
and snapshots. If the administrator has set up some applications in eith er system information or alarm, the
VPort will send out messages or snapshots once these conditions occur .
1st SMTP Server and Sender Email
Setting Description Default
1st SMTP (mail) server SMTP Server’s IP address or URL address. None
1st SMTP account name For security reasons, most SMTP servers r equire the account
name and password to be authenticated.
None
1st SMTP password None
1st Sender’s email
address
For security reasons, SMTP servers must see the exact sender
email address.
None
NOTE
Note that if the
Sender’s email address is not set, a warning message will pop up and the e-
mail system will
not be allowed to operate.
NOTE
The
2nd SMTP Server
and Sender Email are backups that are used if the 1st SMTP Server and Sender Email
fail when connecting or sending email.
Two recipient email accounts are ava ilable for receiving emails sent by the VPo rt. For redundancy, both
addresses receive the sent messages and a larm snapshots simultaneously.
Setting Description Default
1st Recipient’s Email Address Email address of the 1st recipient. None
2nd Recipient’s Email
Address
Email address of the 2nd recipient. None
Moxa VPort 26A-1MP System Configuration
4-15
Dynamic DNS
DDNS (Dynamic Domain Name System) is a combination of DHCP, DNS, and client registration. DDNS
allows administrators to alias the VPort’s dynamic IP address to a static hostname in any of the domains
provided by the DDNS service providers listed on the VPort’s Network/DDNS configuration page. DDNS makes
it easier to access the VPort from various locations on the Internet.
Setting Description Default
Enable DDNS Enable or disable DDNS function Disable
Provider Select the DDNS service providers, includ i ng DynDNS.org
(Dynamic), DynDNS.org (Custom), TZO.com, and dhs.org.
None
Host Name The Host Name you use to link to the VPort. None
Username/ E-mail The Username/E-mail and Password/Key are used to enable
the service from the DDNS service provider (based on the
rules
of DDNS websites).
None
Password/ Key None
NOTE
Dynamic DNS is a very useful tool for accessing a VPort over the Internet, especially for xDSL connections with
a non
-fixed IP address (DHCP). The administrator and users can simplify connecting to a VPort with a non-
fixed
IP address, by using the unique host name in the URL to estab lish a connection with the
VPort.
NOTE
Different DDNS service providers hav e d if f erent application rules. Some applica tions are free of charge, but
most require an application fee.
Universal PnP
UPnP (Universal Plug & Play) is a networking architecture that provides compatibility among the
networking equipment, software, and peripherals of the 400+ vendors that are part of the Universal Plug and
Play Forum. This means that they are listed in the network devices table for the operating system (such as
Windows XP) supported by this function. Users can link to the VPort directly by clicking on the VPort listed in the
network devices table.
Moxa VPort 26A-1MP System Configuration
4-16
Setting Description Default
Enable UPnP Enable or disable the UPnP function. Enable
QoS (ToS)
Quality of Service (QoS) provides traffic prioritization capabilities to ensure that important data is delivered
consistently and predictably. The VPort can inspect layer 3 ToS (Type of Service) information to provide a
consistent classif ic ation of the entire network. The VPort’s ToS capability improves your industrial network’s
performance and determinism for mission critical applications.
Setting Description Factory Default
Enable ToS Enable the ToS
for transmitting the video stream with the given
priority
Disable
DSCP Value Set the mapping table with different ToS values 0, 0
NOTE
To configure the ToS values, map to the network environment settings for QoS priority service.
FTP Server Settings
FTP is the other method available for the VPort to send alarm messages and snapshots.
Moxa VPort 26A-1MP System Configuration
4-17
1st FTP Server
Setting Description Default
1st FTP server FTP server’s IP address or URL address. None
1st FTP server port FTP server’s authentication. None
1st FTP user name None
1st FTP remote folder FTP file storage folder on the remote FTP server. None
1st FTP passive mode Passive transfer solution for FTP transmission through a firewall. Disabled
NOTE
The
2nd FTP Server is a backup in case the 1st FTP Server fails to connect or has trouble sending file s.
NOTE
Whenever the system reboots, a system log will be sent by email or FTP to show the login status of the VPort.
The system log will be sent to the Send er email
address if the SMTP server settings are correct. To send the
system log via FTP, the SMTP server should be erased since the E-mail system is used by default to transmit the
system log.
NOTE
For either e
-mail or FTP, the information of the 1st server sho
uld be entered first. If the 1st server is not set,
the related FTP or email will be cancelled. Note that it may take time to connect to the 2nd server after the first
server fails, and this may affect some applications when adverse conditions occur too of
ten.
Multicast
The VPort 26A-1MP supports the advanced Multicast network protocol IGMP, which can greatly improve the
efficiency of network traffic. In this section, we explain multicasts, multicast filtering, and how multicast can be
implemented on your VPort.
What is Multicast?
A multicast is a packet that is intended fo r “one-to-many” and “many-to-many” communication. Users
explicitly request to participate in the communication by joining an end-station to a specific multicast group. If
the network is set up correctly, a multicast can only be sent to an end-station or a subset of end-stations on a
LAN or VLAN that belongs to the relevant multicast group. Multicast group members can be distributed across
multiple subnetworks. Therefore, multicast transmissions can occur within a campus LAN or over a WAN. In
addition, networks that support IP multicast send only one copy of the desired information across the network.
The packets are only replicated if they reach a network n ode that links to two or more members of the multicast
network. Transmitting packets in this way makes more efficient use of network bandwidth. A multicast packet
is identified by the presence of a multicast group address in the destination address field of the packet’s IP
header.
Benefits of Multicast
The benefits of using IP multicast are t h a t it:
• Enables the simultaneous delivery of information to many receivers in the most efficient, logical way.
• Reduces the load on the source (for example, a server) because it does not need to produce multiple copies
of the same data.
• Makes efficient use of network bandwidth and scales well as the number of participants or collaborators
expands.
• Works with other IP protocols and services, such as Quality of Service (QoS).
There are situations where a multicast approach is more logical and efficient than a unicast approach. A typical
use of multicasts is in video-conferencing, in which high volumes of traffic need to be sent to several
end-stations simultaneously, but for which broadcasting that traffic to all end-stations would seriously reduce
network performance. Several industrial automation protocols, such as Allen-Bradley, EtherNet/IP, Siemens
Profibus, and Foundation Fieldbus HSE (High Speed Ethernet), use the multicast approach. These industrial
Ethernet protocols use publisher/subscriber communications models by multicasting packets that could flood a
Moxa VPort 26A-1MP System Configuration
4-18
network with heavy traffic. IGMP provides the ability to prune multicast traffic so that it travels only to those
end destinations that require the traffic, thus reducing the amount of traffic on the Ethernet LAN.
The network WITHOUT Multicast
The network WITH Multicast
NOTE
The VPort
is the source that delivers the multica st video stream. To benefit from the Multicast protocol, the
gateway or network switch should support the multicast filtering function (such as IGMP Snooping) so that t he
multicast stream is delivered correctly and precisely. To learn more about IGMP Snooping, refer to the Moxa
EtherDeviceTM series Industrial Ethernet Switch user’s manual.
Configuring Multicast Settings
Setting Description Default
Multicast group
address
Multicast Group address for sending video stream. 239.127.0.100
Multicast video port Video port number. Stream 1: 5556
Stream 2: 5560
Multicast audio port Audio port number. Stream 1: 5558
Stream 2: 5562
Multicast TTL Multicast-TTL (Time-to-live) threshold. There is a certain TTL
threshold defined for each network interface or tunnel. A
multicast packet’s TTL must be larger than the defined TTL for
that packet to be forwarded across that link.
128
Continuous Multicast
Push
Enable PUSH control of the multicast video stream Disable
Moxa VPort 26A-1MP System Configuration
4-19
HTTP Event Server
The VPort can send the customized alarm actions and messages to the HTTP Event Servers, which allows users
to design a customized alarm system.
Setting Description Factory Default
Host Name User-defined name for identification Blank
Server 1, 2, 3, 4 The server’s URL ad dress with complete CGI commands Ex.
http:// http event server:Port/CGI_Name
Blank
User name The account name for accessing the HTTP server Blank
Password The password for accessing the HTTP server Blank
Once the Http Alarm is triggered, the VPort will send the following HTTP commands to the HTTP event servers.
GET CGI_Name?address=<Hostname or IP Address>&[Custom CGI] HTTP/1.0\r\n
User-Agent: IP camera V1.1\r\n
[Authorization: Basic <Buse64(username:password)>\r\n]
Host: <HTTP Server IP Address>\r\n
Connection: Keep-Alive\r\n
\r\n
Moxa VPort 26A-1MP System Configuration
4-20
Accessible IP List
The VPort uses an IP address-based filtering method to control access to the VPort.
Accessible IP Settings allow you to add o r remove “Legal” remote host IP address es to prevent unauthorized
access. Access to the VPort is controlled by IP address. That is, if a host’s IP address is in the accessible IP table,
then the host will be allowed access to the VPort. Administrators can allow one of the following cases by setting
this parameter:
• Only one host with a specific IP address can access the VPort. Enter “IP address/255.255.255.255” (e.g.,
192.168.1.1/255.255.255.255)
• Hosts on a specific subnet can access the VPort. Enter “IP address/255.255.255.0” (e.g.,
“192.168.1.0/255.255.255.0”)
• Any host can access the VPort. Disable this function.
Refer to the following table for more configuration examples.
Allowable Hosts Input Formats
Any host Disable
192.168.1.120 192.168.1.120/255.255.255.255
192.168.1.1 to 192.168.1.254 192.168.1.0/255.255.255.0
192.168.0.1 to 192.168.255.254 192.168.0.0/255.255.0.0
192.168.1.1 to 192.168.1.126 192.168.1.0/255.255.255.128
192.168.1.129 to 192.168.1.254 192.168.1.128/255.255.255.128
Moxa VPort 26A-1MP System Configuration
4-21
SNMP
The VPort 26A-1MP supports three SNMP protocols. The available protocols are SNMP V1, SNMP V2c, and SNMP
V3. SNMP V1 and SNMP V2c use a community string match for authentication, which means that SNMP servers
access all objects with read-only or read/write permissions using the community string public/private (default
value). SNMP V3, which requires you to select an authentication level of MD5 or SHA, is the most secure
protocol. You can also enable data encryption to enhance data security. SNMP security modes and security
levels supported by the VPort are shown in the following table. Select one of these options to communicate
between the SNMP agent and manager.
Protocol
Version
Security
Mode
Authentication
Type
Data
Encryption
Method
SNMP V1, V2c V1, V2c Read
Community
Community string No Use a community string match for
authentication
V1, V2c
Write/Read
Community
Community string No Use a community string match for
authentication
SNMP V3 No-Auth No No Use account with admin or user to
access objects
MD5 or SHA MD5 or SHA No Provides authentication based on
HMAC-MD5, or HMAC-SHA
algorithms. 8-
character passwords
are the minimum requirement for
authentication.
MD5 or SHA MD5 or SHA Data
encryption
key
Provides authentication based on
HMAC-MD5 or HMAC-SHA
algorithms, and data encryption
key. 8-character passwords and a
data encryption key are the
minimum requirements for
authentication and encryption.
Configuring SNMP Settings
The following figures indicate which SNMP parameters can be configured. A more detailed explanation of each
parameter is given below the figure.
Moxa VPort 26A-1MP System Configuration
4-22
SNMP Read/ Write Settings
SNMP Versions
Setting Description Default
V1, V2c, V3 Select SNMP protocol versions V1, V2c, V3 to manage the
switch
V1, V2c, V3
V1, V2c Select SNMP protocol versions V1, V2c to manage the switch
V3 only Selec t SNMP protocol versions V3 only to m a na ge the switch
V1, V2c Read Community
Setting Description Default
V1, V2c Read
Community
Use a community string match for authentication, which means
that the SNMP agent accesses all objects with read-only
permissions using the community string public.
public
(max. 30
characters)
V1, V2c Read/Write Community
Setting Description Default
V1, V2c Read/Write
Community
Use a community string match for authentication, which means
that the SNMP agent accesses all objects with read-only
permissions using the community string public.
public
(max. 30
characters)
For SNMP V3, there are two levels of privilege for different accounts to access the VPort. Admin privilege allows
access and authorization to read and write MIB files. User privilege only allows reading the MIB file, but does
not authorize writing to the file.
Root Auth. Type (For SNMP V1, V2c, V3 and V3 only)
Setting Description Default
No-Auth Use admin. account to access objects. No authentication. No
MD5-Auth Provide authentication based on the HMAC-MD5 algorithms.
8-character passwords are the minimum requirement for
authentication.
No
SHA- Auth Provide authentication based on the MAC-SHA algorithms.
8-character passwords are the minimum requirement for
authentication.
No
Root Data Encryption Key (For SNMP V1, V2c, V3 and V3 only)
Setting Description Default
Enable 8-character data encryption key is the minimum requirement
for data encryption. Maximum 30-character encryption key.
No
Disable No data encryption. No
User Auth. Type (For SNMP V1, V2c, V3 and V3 only)
Setting Description Default
No-Auth Use a ccount of admin or user to access objects . No
authentication.
No
MD5-Auth Provide authentication based on the HMAC-MD5 algorithms.
8-character passwords are the minimum requirement for
authentication.
No
SHA- Auth Provide authentication based on the HMAC-SHA algorithms.
8-character passwords are the minimum requirement for
authentication.
No
Moxa VPort 26A-1MP System Configuration
4-23
User Data Encryption Key (For SNMP V1, V2c, V3 and V3 only)
Setting Description Default
Enable 8-character data encryption key is the minimum requirement
for data encryption. Maximum 30-character encryption key.
No
Disable No data encryption. No
Trap Settings
Setting Description Default
Trap Server
IP/Name
Enter the IP address or name of the Trap
Server used by your
network.
No
Trap Community Use a community string match for authentication; Maximum of
30 characters.
No
Private MIB information
The private SNMP Object ID of the VPort is the enterprise value: 8691.8.4.13. This number cannot be changed.
NOTE
The MIB
file is MOXA-VPORT26-
MIB.mib (or.my). You can find it on the software CD or the download cente r of
the Moxa website.
NOTE
To configure the ToS values, map to the network environment settings for QoS priority service.
HTTP Event Server
The VPort can send the customized alarm actions and messages to the HTTP Event Servers, which allows users
to design a customized alarm system.
Setting Description Factory Default
Host Name User-defined name for identification Blank
Server 1, 2, 3, 4 The server’s URL ad dress with complete CGI commands Ex.
http:// http event server:Port/CGI_Name
Blank
User name The account name for accessing the HTTP server Blank
Password The password for accessing the HTTP server Blank
Moxa VPort 26A-1MP System Configuration
4-24
Once the Http Alarm is triggered, the VPort will send the following HTTP commands to the HTTP event servers.
GET CGI_Name?address=<Hostname or IP Address>&[Custom CGI] HTTP/1.0\r\n
User-Agent: IP camera V1.1\r\n
[Authorization: Basic <Buse64(username:password)>\r\n]
Host: <HTTP Server IP Address>\r\n
Connection: Keep-Alive\r\n
\r\n
ModBus/TCP
Modbus is a serial communications protocol which is often used to connect a supervisory computer with a
remote terminal unit (RTU) in supervisory control and data acquisiti on (SCADA) systems. To transmit Modbus
over a TCP/IP network, a standard Modbus/TCP protocol is provided. With the support of the Modbus/TCP
protocol, the SCADA/HMI sy stem can directly communicate with the VPort to acquire its operational status.
Setting Description Factory Default
Enable Modbus/TCP Enable the Modbus/TCP protocol Enable
NOTE
For Modbus address table, please refer to the Modbus_Address_Define.pdf. You can find it on the software CD
or the download center of the Moxa website.
The VPort 26A-1MP supports advanced IEEE 802.1X network authentication function. There are three types of
802.1X supported: EAP-MD5, EAP-PEAP/MSCHAPv2 and EAP-TLS. The Administrator should choose the
appropriate type base on the network system situation.
EAP-MD5
Moxa VPort 26A-1MP System Configuration
4-25
EAP-PEAP/MSCHAPv2
EAP-TLS
NOTE
Please consult an expert or your network administrator for the configurations of 802.1X if you have t rouble in
it.
Telnet
Use this option to Enable/Disable the te ln et fu nc tion .
Moxa VPort 26A-1MP System Configuration
4-26
LLDP
LLDP is an OSI Layer 2 protocol defined by IEEE 802.11AB. LLDP standardizes the self-identification
advertisement method, and allows each networking device, such as a Moxa IP camera or managed switch, to
periodically send its system and configuration information to its neighbors. Because of this, all LLDP devices are
kept informed of each other’s status and configuration, and with SNMP, this i nformation can be transferred to
some network management software, such as Moxa’s MXview for auto-topology and network visualization.
From the VPort’s web interface, you can enable or disable LLDP, and set the LLDP transmit interval. In addition,
you can view each VPort’s neighbor-list, which is reported by its network neighbors. Most importantly, enabling
the LLDP function allows Moxa’s MXview to automatically display the network’s topology and system setup
details for the entire network.
Setting Description Factory Default
Operation Mode Choose the operation mode of LLDP: Disabled, Transmit only,
Receive only, and Transmit and receive.
Transmit and
receive
Transmit interval Sets the transmit interval o f LLDP messages, in seconds. 30
Video
Image Settings
Image Information Setting
Description Default
Description
(max. of 14
characters)
The customized description shown on t he caption to identify
this video camera.
None
Moxa VPort 26A-1MP System Configuration
4-27
Image Appearance Setting
Description Default
Image Information To determine what style of image information is being shown.
Includes Not Shown, Show on the Caption and Show on
image
Not Shown
Image Appearance Position
The position of the Image Appearance window can be changed by configuring Position X (0 to 400) and Position
Y (0 to 300).
Camera Setting
A few camera parameters can be configured for improving image quality according to the environment.
Environment
Setting Description Default
Environment Choose what kind of environment will VPort camera be
installed, optimized parameters will be applied to best fit your
choice
Outdoor
Moxa VPort 26A-1MP System Configuration
4-28
Image Adjustment
Setting Description Default
Saturation Tune the image attribute for the user’s preference for -4 to +6 0
Contrast & Sharpness Tune the image attribute for the user’s preference for -4 to + 4 0
Auto Gain Control
(AGC)
This AGC function provid e s clear image in low light condition.
This controls an amplifier that is used to boost the video signal
when the light dims so as to increase the camera’s sensitivity.
In some bright environment, the amplifier may be overloaded
and which may distort the video signal. So, it is necessary to
monitor the signal level with AGC control circuit and AGC has to
be switched off in case of necessity.
16x
Black level control
(BLC)
This function changes the black level o f the image. Higher
settings will make the image brighter, and lower settings will
make the image darker..
Middle
AWB
(Auto White Balance)
In most condition, you are suggested to choose ATW and allows
the camera to do automatic white balance adjustment. AWB
is
suggested when your camera is watching a scene with a certain
color occupy most for the view.
If you like to use AWB, follow below step.
Step 1:
Move the camera to the white color in the real environment
with normal lighting
Step 2:
Select AWB in the page and then press “Save”
Step 3:
Move the camera back to the scene you are going to watch.
Then select the ATW for correcting the image color
ATW
Appearance Normal – Normal view
Mirror – Image will be displayed as in a mirror
Flip – First 180 degree rotation and then do mirrored display
180 Rotation – Display image after 180 degree rotation
Normal
Digital Noise Reduction
Setting Description Default
Enable Enable digital noise reduction function Off
Day/Night
Setting Description Default
Day (Color) Manually set the camera to day mode (color mode) checked
Night (Black & White) Manually set the camera to night mode (monochrome mode) Unchecked
Light Sensor
(automatic switch the
Day/ Night mode)
Lets the camera light sensor switch between day and night
modes based on ambient illumination level.
Set the switch lux level (from level 1 to level 5), and
detection
duration (1 to 60 seconds) to define ho w long the illumination
level should persist before switching.
Unchecked
DI Control Switch day/night when by DI
• Pull High: camera will do day/night switch whenever DI
status is high
• Pull Low: camera will do day/night switch whenever DI
status is low
unchecked
Trigger relay output
when day/night mode
switch
Trigger relay output when day/night mode switch, relay status
for day/night mode could be configured separately
unchecked
Moxa VPort 26A-1MP System Configuration
4-29
Auto Exposure Shutter
Setting Description Default
Auto Level Higher level will extend auto shutter speed slower, hence
brighter image; lower level will do opposite.
0
WDR
Setting Description Default
WDR
(Wide Dynamic Range)
Higher level means more strong WDR effect. Choose higher
WDR level when you have strong lighting and dark area
co-exist in one video scene
Level 8
ROI (Region of Interest)
When network bandwidth is limited, HD video stream in realtime may be too huge for the network to bear, and
in that condition, VPort IP camera is able to automatically allocate available bandwidth to those parts of video
that of your bigger interest. For example, when watching a factory entrance, camera can allocate more
bandwidth for entry way while only allocate minimum bandwidth for the wall in the scene.
ROI
Setting Description Default
Enable Enable ROI function Off
Region 1/2/3
Assign priority to up to 3 different regions in the camera view.
unchecked
High/Medium/Low High –
camera will reserve a majority of bandwidth for this part
of video
Medium –
camera will reserve moderate bandwidth for this part
of video
Low – camera will reserve only minimum bandwidth for this
part of video
Low
Moxa VPort 26A-1MP System Configuration
4-30
Privacy mask
VPort IP camera supports up to3 privacy mask areas on image for privacy protection.
Privacy Mask
Setting Description Default
Enable Enable privacy mask function Off
Mask 1/2/3
Enable up to 3 different privacy mask area. Once enabled, you
can drag mask area directly in the camera s cene
unchecked
NOTE
There is no way to recover masked video no matter in live or playback, make sure you use this function
carefully
Video Performance
The VPort IP camera can send a maximum of three simultaneous video streams: two H.264 and one MJEPG. In
fact, the VPort IP camera has two encoder engines. The first encoder engine can gener ate one H.264 video
stream, and this H.264 video stream is a completely independent video s tr eam, which means its resolution,
FPS and video quality can be configured independently. The second encoder engine can generate one H.264
video stream and one MJPEG video stream. Because both the H.264 and MJPEG video streams come from the
same encoder engine, their resolution must be the same, but the FPS and the Video Quality can be configured
separately. The administrator can set t he Resolution, Max. Frame Rate and Video Quality on this web page.
Moxa VPort 26A-1MP System Configuration
4-31
Resolution Type
For meeting different CCTV resolution requirement, there are NTSC or PAL mode can be selected.
NOTE
Due to there is only one video source, different resolution will have differen
t viewing angle.
Streams
Setting Description Default
Enable the video
streams
To enable the VPort to send this video streams or not. Enable stream 1:
H.264 and stream 2:
MJPEG
Codec Type
This codec type shows the codec of each video stream.
Resolution
The VPort 26A-1MP supports 5 different resolutions: WXGA, HD, SVGA, Full D1, 4CIF, VGA, CIF, and Q CIF.
Setting Description Default
Select the image size 8
image resolutions (size) are provided. The administrator can
choose each option with NTSC or PAL modulation.
1280x720
Resolution NTSC PAL
WXGA 1280x800 1280x800
HD 1280x720 1280x720
SVGA 800 x 600 800x 600
Full D1 720 x 480 720 x 576
4CIF 704 x 480 704 x 576
VGA 640 x 480 640 x 480
CIF 352 x 240 352 x 288
QCIF 176 x 112 176 x 144
Max. FPS (Frame per second)
Setting Description Default
Maximum frame rate The maximum frame rate is different to accommodate different
modulations of video input. Administrators can also set up the
maximum frame rate to optimize bandwidth use.
NTSC: 1, 3, 5, 10, 15, 20, 25, 30
PAL: 1, 3, 5, 8, 12,16, 20, 25
30 for NTSC, 25 for
PAL
NOTE
Frame rate (frames per second) is determined by the resolution, image data size (bit rate), and transmission
traffic status. The Administrator and users can check the frame rate statu s in the
FPS Status
on the VPort’s
web homepage.
Moxa VPort 26A-1MP System Configuration
4-32
Video Quality Control
Video Quality Control is used to optimize the bandwidth of the MPEG4 video stream. There are 2 modes for
video quality control.
Setting Description Default
Fixed bit rate
(Only for H.264)
The administrator can fix the bandwidth to tune the video
quality and FPS (frames per second) to the optimum
combination.
The VPort will tune the video performance according to the
configured bandwidth. A higher bandwidth means better
quality and higher FPS.
4000Kbps in
1280x720 resolution
Fixed Quality The administrator can set the image quali ty to one of 5
standards: Medium, Standard, Good, Detailed, or
Excellent. The VPort will tune the bandwidth and FPS
automatically to the opti mum combination.
Good
CBR Pro™
General CBR (constant bit rate) configuration limits throughput to 1 second, but since video streaming is
designed to transmit immediately to shorten latency time, network thro u ghp ut may experience a burst in
action during short time periods, in which case packet loss will occur if the network bandwidth buffer is not
large enough. When packet loss occurs, images will show a mosaic effect. For this reason, the VPort 26A-1MP
supports an advanced CBR Pro™ function, which can enable the flow control of image packets to ensure no
packet loss for limited bandwidth transmissions, such as on xDSL or wireless networks.
Image without packet loss Image with packet loss
Setting Description Default
Limits the maximum
throughput of each
connection in
kbits
within
milliseconds
Configure how much throughput is allowed on the networ k
within the given number of milliseconds. For example, if the
configuration is 20 kbits within 5 milliseconds, the
video packet
throughput will be limited to 20 kbits within 5 milliseconds.
20 kbits within 5
milliseconds.
NOTE
The image quality, FPS, and bandwidth are influenced significantly by network throughput, system network
bandwidth management, applications the VPort runs (such as VMD), how complicated the image is, and the
performance of your PC or notebook when displaying images. The administrator should take into consideration
all of these variables when designing the video over IP system, and when specifying the requirements for the
video system.
NOTE
Visit
http://www.moxa.com/event/Net/2012/IP_CCTV_Calculator/index.htm to get help for network
bandwidth estimation of different resolutions, FPS, video content, etc.
Moxa VPort 26A-1MP System Configuration
4-33
Audio
Audio Source
The VPort supports real-time and synchronous video/audio transmission. The default audio input is line-in. If a
microphone is being used, your administrator will need to enable the microphone.
PTZ
For its HD 720P (1280x720) image resolution, VPort 26A-1MP is able to provide crystal clear video image, and
viewers are allowed to see finest detail even after image zoomed. Therefore, VPort 26A-1MP comes with digital
PTZ function that enables users to zoom in camera image to observe the deta il.
Digital PTZ
Before use digital PTZ, you need to enable digital PTZ function in VPort 26A-1MP setting page as shown below.
First check enable, then choose the PTZ function you are like to operate. Note that digital zoom and digital
pan/tilt functions could be enabled separately.
Press save when you done digital PTZ settings. Once Digital PTZ function is enabled, you can then go to IP
camera home page and click on Show PTZ Control Panel to perform digital PTZ functions.
Below is the PTZ control panel you will see when you click “Show PTZ Control Panel” in IP camera home page.
You can press “+” button in the bottom right of the page to perform digital zoom function. Aft er digital zoom,
you can then navigate the camera image by press direction button in the wheel.
Moxa VPort 26A-1MP System Configuration
4-34
NOTE
Direction button in
the wheel will not be displayed until digital zoom is performed. Once camera image is
zoomed out to original size, direction button will disappear again.
NOTE
Direction button in the wheel will not be displayed until digital z oom is performed. Onc e ca
mera image is
zoomed out to original size, direction button will disappear again.
DynaStreamTM
DynaSteamTM is a unique and innovative function that allows for adaptive frame rates in response to events on
the network, such as event triggers and system commands. When network traffic becomes congested,
DynaStream™ allows VPort products to respond to CGI, SNMP, and Modbus commands from SCADA (as well as
the VPort 26A-1MP’s VMD, DI, CGI events, and video loss triggers) and automatically decrease the frame rates
to reduce bandwidth consumption. Th is reserves bandwidth for the SCADA system to maintain Quality of
Service (QoS) and guarantees that the SCADA performance will not be impacted by video traffic. For example,
the frame rate can be set low during regular streaming to reduce bandwidth usage and automatically switch to
a high frame rate during triggered events to ensure quick transmission of critical video data or video streams,
or to provide detailed visual images for problem analysis.
NOTE
For enabling
the DynaStream function from CGI commands and Modbus TCP, please refer to the CGI
Commands User’s Manual of VPort SDK PLUS and Modbus Address Table
Basic
The administrator can adjust the number of frames per second for each channel. There are two types of frame
rate status: Live and Alarm. Live status refers to the normal frames rates for live video displays. Alarm status
refers to what the frame rate will be adj usted to when the DynaStream function is activated.
Currently, the video stream for DynaStream is only set up for H.264 video streams, and the resolution and
quality are the same as for the settings i n the Video Performance configuratio n.
Setting Description Factory Default
Max. FPS For setting the maximum frame rate per second. PAL: 25
NTSC: 30
After setting the Alarm frame rate, you may preview the video performance by clicking the Test button to
ensure it meets your requirements
Moxa VPort 26A-1MP System Configuration
4-35
Conditions
The administrator can set up DynaStream’s trigger conditions for facilitating automatic frame rate adjustment,
e.g., from Live to Alarm status.
Currently, there are four types of trigger conditions: CGI Event, Motion Detection, and Digital input.
Setting Description Factory Default
Enable To enable or disable the DynaStream function. Disable
Duration This refers to the time period that DynaStream
is in operation.
For example, if the duration is set to 5 seconds, then the frame
rate will change from the Live to the Alarm status for the
duration of 5 seconds. After 5 seconds, the frame rate will
return to the Live status setting.
5 seconds
Trigger Channel To enable or disable the video channels. Disabled
Alarm
System
In addition to the LED indicators, network disconnected alarm is provided by the VPort 26A-1MP for notifying
the system operators and administrator, also store video image in SD card so that you can retrieve recorded
image after network connection is restored.
Setting Description Factory Default
Enable network
disconnected alarm
To enable or disable the network disconnected alarm. Disable
Trigger Relay alarm Enable or disable the triggering of Relay Disable
Video record Once the network link is
down, video streams can be recorded
on the SD card, and once the network link is back up
, the video
recording will be stopped.
Disable
Moxa VPort 26A-1MP System Configuration
4-36
NOTE
For the
VPort P26A-1MP, the PoE model is powere d via the Ethernet cable, s
o once the network cable is broken,
it will be powered off, and there is no way
to record video on the SD card.
Basic
Alarm Time Interval
Setting Description Default
Delay second(s) before
detecting the next
alarm
Set the minimum time interval before another event alarm is
triggered.
32 seconds
(10 to 999 seconds)
NOTE
The delay before triggering the next alarm cannot be less than the time needed to take a snapshot after an
event (post
-event image).
Send Alarm with Snapshot images
Setting Description Default
Take snapshot
seconds(s) before the
event
A snapshot image is taken this number of seconds before the
event alarm is triggered.
2 seconds
(from 1 to 6
seconds)
Take snapshot
seconds(s) after the
event
A snapshot image is taken this number of seconds after the
event alarm is triggered.
11 seconds
(from 1 to 999
seconds)
NOTE
VPort
products will take 3 JPEG snapshot images: VPRE.JPG (pre-
event), VTRG.JPG (the moment of event) and
VPOS.JPG (post-event) for the video channel when the trigger condition is met. The three snapshots can also
be downloaded by Email and FTP.
Moxa VPort 26A-1MP System Configuration
4-37
Suffix of Image File Name in FTP and Mail attachment
The snapshot images can be sent either by email or FTP. Administrators can add a suffix to the filename of each
JPEG snapshot image to make it easier to identify the files when using FT P to d ownload the snapshots.
Setting Description Default
With Date and Time Enable or disable adding the date and time to the filename. Disable
With Customized words Enable or disable adding some additional custom text to the
filename to identify the snapshot imag e.
Disable
DI, Relay Status
Administrators can check the current DI and Relay status of the VPort in the “DI, Relay Status” section on the
“Event Alarm Basic Settings” page. Two options are available to return the relay’s status back to the system
defaults. To enable the function, check the Override Relay 1 warning setting box, and then click on Save.
In addition, in the “Relay Active behavior” section, you can configure the duration of the relay action, with
options of activating the relays continuously, for the specified Alarm Interval Time, or for the period of time
when the alarm is triggered.
Schedule
A schedule is provided to set event alar ms for daily security applications.
Event Type
Setting Description Default
Digital Input, Video
Motion Detection, CGI
Event, and Camera
Tamper Event
Set up the schedule of each kind of event type. Digital Input
Weekly Schedule
Setting Description Default
Event Alarms are active
all the time
Select the option “Event Alarms are act iv e all the time” Event Alarms are
active based on a
weekly schedule
Event Alarms are
active
based on a weekly
schedule
Select to operate event alarms on a week ly schedule.
Moxa VPort 26A-1MP System Configuration
4-38
NOTE
The applications described in the following sections will only work properly if either
Event Alarms are
active
all the time
or Event Alarms are active based on weekly schedule is Selected.
Setting Description Default
□Sun □Mon □Tue □Wed
□Thu □Fri □Sat
Select the weekday for scheduling event alarms. None
Begin 00:00 Set the start time of the event alarm. 00:00
Duration 00:00 Set the duration for the event alarm to be active. 00:00
NOTE
Administrators can use the following steps to set up an event schedule:
Select Event Type
Enable “Event Alarms are activ e b a sed on weekly schedule”
Select the weekday
Set the start time
Set the duration this event will be active.
Save
Event Alarm
Four kinds of event alarm are provided by the VPort for building an intelligent video surveillance system.
Alarm Type Triggered Condition Triggered Action
Video Motion Detection
(VMD)
VMD 1
VMD 2
VMD 3
1. Trigger Relay
2. Email
3. FTP
4. HTTP Event Server
5. Record on SD card
Digital Input High, Low, Rising and Falling 1. Trigger Relay
2. Email
3. FTP
4. HTTP Event Server
5. Record on SD card
CGI Event The CGI trigger message 1. Trigger Relay
2. Email
3. FTP
4. HTTP Event Server
5. Record on SD card
Camera Tamper Camera tampering by painting, blocking,
defocusing, or changing the position.
1. Trigger Relay
2. Email
3. FTP
4. HTTP Event Server
5. Record on SD card
Moxa VPort 26A-1MP System Configuration
4-39
Digital Input
Setting Description Default
Enable digital input
alarm
Enable or disable the digital input alarm. Disable
Trigger Conditions
Setting Description Default
High The DI is always in the “High” state after an alarm is detected. Disable
Low The DI is always in the “Low” state after an alarm is detected. Enable
Rising
The DI works from state “Low” to state “High” and th en back to
state “Low” when an alarm is detected.
Disable
Falling The DI works from state “High” to
state “Low” and then back to
state “High” when an alarm is detected.
Disable
NOTE
Please refer to Chapter 1 to see the DI sp ecifications.
Trigger Actions
Setting Description Default
Trigger Relay1 alarm Once this DI is triggered, the Relay1 alarm will be activated Disable
Send snapshot image
via E-mail
Once this DI is triggered, the VPort will send the snapshot
images set in the Event Alarm/Basic page to the E-mail
addresses, which are set in the Network/ SMTP Server
page.
Disable
Send snapshot image
via FTP
Once this DI is triggered, the VPort will send the snapshot
images set in the Event Alarm/Basic
page to the FTP server,
which are set in the Network/ FTP Server page.
Disable
Send message via HTT
P
Event Servers
Once this DI is triggered, the VPort will send the message set in
HTTP Action Setting to the HTTP event servers, which are set
in the Network/ HTTP Event Server page.
Disable
Record video on SD
card for Sec
Once this DI is triggered, then for a configured time period
VPort will record video to an (optional) SD card.
Disabled
HTTP Action Setting
Setting Description Default
Server 1, 2, 3, 4 Select the HTTP event server for sending the HTTP action Disable
Blank column Administrators can custo mize the message sent to the HTTP
event sever in this column
Blank
Moxa VPort 26A-1MP System Configuration
4-40
Motion Detection
Video Motion Detection (VMD) is an intelligent event alarm for video surveillance network systems. With the 3
area-selectable VMDs and sensitivity/percentage tuning, administrators can easily set up the VMD alarm to be
active 24 hours a day, 7 days a week.
Setting Description Default
Enable VMD alarm Enable or disable the Video Motion Detection alarm Disabled
Show alert on the image when
VMD is triggered
Enable or disable the “show the alert,” which when enabled
displays a red square frame on the video image of
the VMD alarm
notification
Disabled
Show motion block on the image
(Assistance function, disable it
when setting is done)
Enable this item for real-time motion detection, which is related
to VMD sensitivity configuration.
Disabled
Show motion percent info on
the image (Assistance function,
disable it when setting is done)
Enable this item to show the change in percentage of motion
detection, which is related to the VMD’s percentage
configuration.
Disabled
Moxa VPort 26A-1MP System Configuration
4-41
NOTE
Once the
Show alert on the image when VMD is triggered is enabled, the red frames that appear on the
homepage image indicate the size of the VMD window set up by the administrator.
NOTE
To enable
Show motion block on the image and Show motion percent info on the image, the image
appearance
in the video configuration must be configured to show on the image.
Note Show motion block on the image
and Show motion percent info on the image are to help the
administrator configure the VMD (
video motion detection) function. Once both items are enab led, the
administrator can see the motion detection real
-time status and the change in
percentage of the VMD area on
the video
image. If the motion status and change of
percentage are just what the administrator expects, then
the
configurations of sensitivity and percentage of VMD are confirmed. Before clicking on Save,
disable both
items after the configurations are confirmed.
Setup a VMD Alarm
Setting Description Default
Enable Enable or disable the VMD1, 2, and 3 Disabled
Window The name of each VMD window Blank
Percent The minimum percen ta ge of an image change for triggering VMD. Decrease the
percentage to make it easier to trigger VMD.
80
Sensitive The measurable difference between two sequential images for triggering VMD.
Increase the sensitivity to make it easier for VMD to be triggered.
1
Moxa VPort 26A-1MP System Configuration
4-42
NOTE
After setting the VMD Alarm, click the
Save button to save the changes
Trigger Conditions and Actions
For each VMD administrators can set triggers, such as “send snapshot image via E-mail”, “send snapshot image
via FTP”, “send Message via HTTP event servers”, “save snapshot on storage” and “record video on SD card”.
Setting Description Default
Trigger Relay1 alarm Once the VMD is trigge red, the Relay alarm w ill be activated Disabled
Send snapshot image
via E-mail
Once this VMD is triggered, the VPort will send the snapshot
images set in the Event Alarm/Basic page to the E-mail
addresses, which are set in the Network/ SMTP Server
page.
Disabled
Send snapshot image
via FTP
Once this VMD is triggered, the VPort will send the snapshot
images set in the Event Alarm/Basic
page to the FTP server,
which are set in the Network/ FTP Server page.
Disabled
Send message via HTTP
Event Servers
Once this VMD is triggered, the VPort will send the message set
in HTTP Action Setting
to the HTTP event servers, which are
set in the Network/ HTTP Event Server page.
Disabled
Record video on SD
card for Sec
Once this VMD is triggered, then for a configured time period
VPort will record video to an (optional) SD card.
Disabled
HTTP Action Setting
Setting Description Default
Server 1, 2, 3, or 4 Select the HTTP event server for sending the HTTP action Disabled
Blank text box For customizing the message to the HTTP event server. Blank
How to Configure a VMD alarm
Step 1:
Check the Enable VMD alarm box. If the Administrator wants to show the red frame alert on the image on the
VPort 26A-1MP’s web homepage, check the Show alert on the image when VMD is triggered box.
Step 2:
Assign a name to the VMD window in the Window Name column.
Step 3:
Set up the Percent% parameters for individual VMD windows and the Sensitivity for all VMD windows. Click
on the Save button to save these two configurations.
Step 4:
Select Show motion block on the image and Show motion percent info on the image, an d check the
real-time motion detection status an d motion detection change of percentage on the homepage’s image to see
if the configurations of VMD are OK or not. If n ot, go back to th e configuration page to change the percentage
and sensitivity, and then check again. Once the VMD configurations are confirmed, disable Show motion
block on the image and Show motion percent info on the image.
Step 5:
Click Save to save the settings.
Step 6:
To test the VMD condition, check the action of the graphics bar on the left side of the save button. Wave your
hand in front of the camera, in the VMD area, and then note which color shows up in the graphics bar. Green
means VMD is not triggered. Red means V MD is triggered.
Step 7:
Set up the Trigger Conditions and Actions of each VMD, and then c lick on the Save button to save these
configurations.
Moxa VPort 26A-1MP System Configuration
4-43
NOTE
Video Motion Detection is provided as a reference because it is environment-dependent. When the settings are
configured to be very sensitive to motion, some triggered events might actually be false alarms that were
triggered by only a small difference between sequential images. These false alarms might be triggered by the
flicker of fluorescent lights, the movement of shadows, or similar everyday events.
CGI Event
The VPort can accept 5 CGI commands, which are sent from external devices, such as ioLogik series Ethernet
I/O, to be the event alarms.
NOTE
The VPort only can accept the CGI comman d s that follow the VPort’s CGI commands fo rmat.
CGI Event Trigger Actions
Setting Description Default
Enable CGI Event alarm Enable or disable CGI Event alarm. Disable
Event Select the Event 1, 2, 3, 4, 5 Disable
Trigger Relay1 alarm Once this CGI Event is triggered, the Relay alarm wil l be
activated
Disabled
Send snapshot image
via FTP
Once this CGI Event is triggered, the VPort will send the
snapshot images set in the Event A la r m / Basic page to the
FTP server, which are set in the Networ k/FTP Server page.
Disable
Send message via HTTP
Event Servers
Once this CGI Event is triggered, the VPort will send the
message set in the HTTP Action Setting to the HTTP event
servers, which are set in the Network/HTTP Event Server
page.
Disable
Save snapshot to
storage
The pre-alarm, trigger, and post-
alarm snapshot images can be
saved on an (optional) SD card.
Disabled
Record video on SD
card for Sec
Once this VMD is triggered, then for a configured time period
the VPort will record video to an (optional) SD card.
Disabled
Moxa VPort 26A-1MP System Configuration
4-44
HTTP Action Setting
Setting Description Default
Server 1, 2, 3, 4 Select the HTTP event server for sending the HTTP action Disable
Blank column Administrators can customize the message sent to the HTTP
event sever in this column
Blank
Camera Tamper
The VPort 26A-1MP support camera tamper function to detect any malicious behavior that is done to the
camera, such as spray painting, view blocking, angle adjustment, etc. This page allows you to configure the
parameters and alarm condition/action of camera tamper alarm.
Setting Description Default
Enable camera tamper
alarm
Enable or disable the digital input alarm Disabled
Alarm osd Determine whether or not camera will display on screen
warning square when camera tamper alarm is triggered
Not Display
Trigger Conditions
Setting Description Default
Cover Area How much percentage of the camera view should be affected
before camera tamper alarm is triggered.
30%
Duration How long should the camera tamper behavior persist before
alarm is triggered
5 sec
Trigger Actions
Setting Description Default
Enable CGI Event alarm Enable or disable CGI Event alarm. Disable
Event Select the Event 1, 2, 3, 4, 5 Disable
Trigger Relay1 alarm Once this CGI Event is triggered, the Relay alarm wil l be
activated
Disabled
Send snapshot image
via FTP
Once this CGI Event is triggered, the VPort will send the
snapshot images set in the Event Alarm/Basic page to the FTP
server, which are set in the Network/FTP Server page.
Disable
Send message via HTTP
Event Servers
Once this CGI Event is triggered, the VPort will send the
message set in the HTTP Action Setting to the HTTP event
servers, which are set in the Network/HTTP Event Server page.
Disable
Save snapshot to
storage
The pre-alarm, trigger, and post-
alarm snapshot images can be
saved on an (optional) SD card.
Disabled
Record video on SD
card for Sec
Once this VMD is triggered, then for a configured time period
the VPort will record video to an (optional) SD card.
Disabled
Moxa VPort 26A-1MP System Configuration
4-45
HTTP Action Setting
Setting Description Default
Server 1, 2, 3, 4 Select the HTTP event server for sending the HTTP action Disable
Blank column Administrators can customize the message sent to the HTTP
event sever in this column
Blank
Once the configurations are done, a purple box will appear in the right-top corner of the image to indicate that
environmental learning is underway; the procedure should take between 1 and 3 minutes. After the learning is
complete, the purple box will disappear. Once the tamper alarm is triggered, the box will reappear, but the
color will now be yellow.
Camera tamper in environment learning
Camera tamper is triggered
A
A. Frequently Asked Questions
Q: What if I forget my password?
A: Every access to the IP camera needs authentication, unless the admin password is set up as blank. If you
are one of the managed users, you will need to ask the administrator for the password. If you are the
administrator, there is no way to recover the admin password. The only way to regain access to IP camera
is to utilize the
RESET button to restore the factory settings (see Chapter 1 for details).
Q: Why can’t I see video from the IP camera after it has been authenticated?
A: There are many possible
scenarios:
(a)
If the IP camera is installed correctly and you are accessing the IP camera fo r the first time using
Internet Explorer, adjust the security level of Internet Explorer to allow installation of plug
-ins.
(b)
If the problem still exists, the n
umber of users accessing the IP camera at the same time may exceed
the maximum that the system allows.
(c) If the video is still not
displayed
, please try to run the Factory default to see if it is in work properly.
Q: What is the plug
-in for?
A: The
plug-in provided by IP camera is used to display motion pictures. The plug-in is needed because
Internet Explorer does not support streaming technology. If your system does not allow installation of
plug
-in software, the security level of the web browser
may need to be lowered. It is recommended that
you consult the network supervisor in your office before adjusting the security level.
Q: Why is the timestamp different from the system time of my PC or notebook?
A: The timestamp is based on the system
time of the IP camera. It is maintained by an internal real-time
clock, and automatically synchro nizes with the time server if the video encoder is connected to the
Internet and the function is enabled. Differences of several hours may result from the time zone setting.
Q: How many users are allowed to access the IP camera at the same time?
A: Basically, there is no limitation. H owever the video quality also depends on the network
. To achieve
the best
effect, the VPort 26A-1MP IP camera will allow 5 video streams for udp/tcp/http c
onnections. We
recommend using
multicast streaming if you need to host a large number of users.
Q: What is the IP camera’s video rate?
A: The codec can process 30 frames per second internally. However the total performance is subject to many
variables, as listed below:
Network throughput.
Bandwidth share.
Number of users.
More complicated objects res ult in larger image files.
The speed of the PC or notebook that is responsible for displaying images.
Moxa VPort 26A-1MP Frequently Asked Questions
A-2
Q: How can I
keep the IP camera as private as possible?
A: The IP camera is designed for surveilla nce purposes and has many flexible inter f aces. The user
authentication and special confirmation when installing can keep the video encoder from unauthorized
access. You m
ay also change the HTTP port to a non-
public number. Check the system log to examine any
abnormal activities and trace the origins.
B
B. Modbus Address Table
Read/Write Registers (Support Function Code 4 & Function Code 3)
Address Word (2 bytes) Item name R/W Description
0x0000 1 Vender ID R 0x1393
0x0001 1 Un it ID R 0x01
0x0002 1 Product Code R 0x880E
0x0010 20 Vender Name R moxa
0x0030 20 Product Name R VPort 36-1MP
0x0050 1 Ser ial Number R
R
R
R
0x0051 2 Firmware Version
0x0053 2 Relea se Dat e
0x0055 2 MAC Address
0x0080 1 DI Status R 1: High
0: Low
0x0084 1 Rel ay Status R/W 0: Open
1: Close
0x0701 1 Record Status R/W R:
0: No record
1: recording
W:
0: stop record
1: start record
0x0801 1 Dynastream Status R/W R
0: No run dynastream
1: run dynastream
W
0: stop dynastream
1: start dynastream
C
C. Time Zone Table
The hour offsets for different time zones are shown below. You will n eed this information when setting the time
zone in automatic date/time synchronization. GMT stands for Greenwich Mean Time, which is the global time
that all time zones are measured from.
(GMT-12:00) International Date Line West
(GMT-11:00) Midway Island, Samoa
(GMT-10:00) Hawaii
(GMT-09:00) Alaska
(GMT-08:00) Pacific Time (US & Canada), Tijuana
(GMT-07:00) Arizona
(GMT-07:00) Chihuahua, La Paz, Mazatlan
(GMT-07:00) Mountain Time (US & Canada)
(GMT-06:00) Central A me rica
(GMT-06:00) Central Time (US & Canada)
(GMT-06:00) Guadalajara, Mexico City, Monterrey
(GMT-06:00) Saskatchewan
(GMT-05:00) Bogota, Lima, Quito
(GMT-05:00) Eastern Time (US & Canada)
(GMT-05:00) Indiana (East)
(GMT-04:00) Atlantic Time (Canada)
(GMT-04:00) Caracas, La Paz
(GMT-04:00) Santiago
(GMT-03:30) Newfoundland
(GMT-03:00) Brasilia
(GMT-03:00) Buenos Aires, Georgetown
(GMT-03:00) Greenland
(GMT-02:00) Mid-Atlantic
(GMT-01:00) Azores
(GMT-01:00) Cape V erde Is.
(GMT) Casablanca, Monrovia
(GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, Londo n
(GMT+01:00) Amsterdam, Berlin, Bern, Stockholm, Vienna
(GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague (GMT+01 :00) Brussels,
Copenhagen, Madrid, Paris
(GMT+01:00) Sarajevo, Skopje, Warsaw, Zagreb
(GMT+01:00) West Central Africa
(GMT+02:00) Athens, Istanbul, Minsk
(GMT+02:00) Bucharest
(GMT+02:00) Cairo
(GMT+02:00) Harare, Pretoria
(GMT+02:00) Helsinki, Kyiv, Riga, Sofia, Tallinn, Vilnius
(GMT+02:00) Jerusalem
(GMT+03:00) Baghdad
Moxa VPort 26A-1MP Time Zone Table
C-2
(GMT+03:00) Kuwait, Riyadh
(GMT+03:00) Moscow, St. Peter s burg, Volgograd
(GMT+03:00) Nairobi
(GMT+03:30) Tehran
(GMT+04:00) Abu Dhabi, Muscat (GMT+04:0 0) Baku, Tbilisi, Yerevan (GMT+04:30) Kabul
(GMT+05:00) Ekaterinburg
(GMT+05:00) Islamabad, Karachi, Tashkent (GMT+05:30) Chennai, Kolkata, Mumb ai, New Delhi
(GMT+05:45) Kathmandu
(GMT+06:00) Almaty, Novosibirsk (GMT+06:00) Astana, Dhaka
(GMT+06:00) Sri Jayawardenepura (GMT+06:30) Rangoon
(GMT+07:00) Bangkok, Hanoi, Jakarta (GMT+07:00) Krasnoyarsk
(GMT+08:00) Beijing, Chongqing, Hongkong, Urumqi
(GMT+08:00) Taipei
(GMT+08:00) Irkutsk, Ulaan Bataar (GMT+08:00) Kuala Lumpur, Singapore (GMT+08:00) Perth
(GMT+09:00) Osaka, Sapporo, Tokyo (GMT+09:00) Seoul
(GMT+09:00) Yakutsk
(GMT+09:30) Adelaide
(GMT+09:30) Darwin
(GMT+10:00) Brisbane
(GMT+10:00) Canberra, Melbourne, Sydney
(GMT+10:00) Guam, Port Moresby (GMT+1 0:00) Hobart
(GMT+10:00) Vladivostok
(GMT+11:00) Magadan, Solomon Is., New Caledonia
(GMT+12:00) Auckland, Wellington (GMT+ 12:00) Fiji, Kamchatka, Marshall Is.
(GMT+13:00) Nuku’alofa
D
D. Technical Specifications
Camera
Sensor:
1/2.7” HD progressive scan CMOS
Lens:
Focal length = 3 to 9 mm, F = 1.2
Auto Iris Type:
DC drive
Camera Angle
(controlled manually):
• Pan: ±175°, Tilt: 0 to 85°
• Rotation: PAN: ±180°
Illumination:
• Color: 0.2 lux at F1.2
• B/W: 0.05 lux at F1.2
Synchronization:
Internal
White Balance:
ATW/AWB (range: 3200 to 10000°K)
Dynamic Range:
• Color: 100 db
• B/W: 11
0 db
Electronic Shutter:
Auto, 1/30 to 1/25,000 sec.
S/N Ratio:
50 dB (Gamma, Aperture, AGC OFF, DNR ON)
ICR Control:
Auto
DNR:
Built-in DNR (digital n oise reduction)
WDR:
Level 1-8/ off
AGC Control:
2X, 4X, 8X, 16X, 32X, 64X
Flickerless Control:
Indoor/Outdoor modes
Black Level Control:
High, Medium, Low
Auto Exposure:
Level ±5
Image Rotation:
Flip, Mirror, and 180° rotation
Image Setting:
Manual tuning with saturation, sharpness, and contrast
Video
Video Compression:
H.264 (ISO/IEC 14496-10) or MJPEG
Video Output:
Via Ethernet
Video Streams:
Maximum of 3 video streams (2 x H.264, 1 x MJPEG)
Video Resolution and FPS (frames per second):
NTSC PAL
Size Max. FPS Size Max. FPS
QCIF 176 x 112 30 176 x 144 25
CIF 352 x 240 30 352 x 288 25
VGA 640 x 480 30 640 x 480 25
4CIF 704 x 480 30 704 x 576 25
Full D1 720 x 480 30 720 x 576 25
SVGA 800 x 600 30 800 x 600 25
HD 1280 x 720 30 1280 x 720 25
WXGA 1280 x 800 30 1280 x 800 25
Note: Each independent stream supp orts up to 30
FPS.
Moxa VPort 26A-1MP Technical Specifications
D-2
Video Viewing:
• DynaStream™ supported for changing the video frame rate automatically
• CBR Pro™ for good image quality in limited bandwidth transmission
• 3 privacy mask areas provided
• Adjustable image size and quality
• Timestamp and text overla
y
• Maximum of 5 simultaneous unicast connections
• ROI (Region of Interest) configuration for up to 3 areas
PTZ:
Digital PTZ with 4X zoom
Audio
Audio Inputs:
1 line-in or mic-in with 2-pin terminal block connector
Audio Outputs:
1 line-out with 2-pin terminal block connector
Network
Protocols:
TCP, UDP, HTTP, SMTP, FTP, Telnet, NTP, DNS, DHCP, UPnP , RTP, RTSP, ICMP, IGMPv3 , QoS,
SNMPv1/v2c/v3, DDNS, Modb u s /TCP, 802.1X, SSH/HTTPS
Ethernet:
1 10/100BaseT(X) Ethernet port, RJ45 connector
GPIO
Digital Inputs:
1, max. 8 mA
• Low: +13 V to +30 V
• High:
-30 V to +3 V
Relay Outputs:
1, max. 24 VDC @ 1 A
LED Indicators
STAT:
Indicates if the system is booted properly or not
Network:
10 Mbps or 100 Mbps
Power:
Power on/off
DIP Switch:
To turn the LED light on/off
Local Storage
SD Socket:
Standard SD socket (SDHC)
Power Requirements
Power Input:
• VPort 26A
-1MP: 1, 12/24 VDC or 24 VAC
• VPort P26A
-1MP: Power-over-Ethernet (PoE, IEEE 802.3af)
Power Consumption:
• VPort 26A
-1MP: 4.7 W
• VPort P26A
-1MP: 5.8 W
Physical Characteristics
Housing:
Metal, IP66 rated for rain and dust protection, vandal-proof
Dimensions:
149 mm (diameter) x 120 mm (h e ight)
Installation:
Surface mounting, or outdoor mounting with accessories
Alarms
Intelligent Video:
Tamper alarm
Video Motion Detection:
Includes sensitivity settings
Video Loss:
Video loss alarm
Scheduling:
Daily repeat timing schedule
Imaging:
JPEG snapshots for pre/trigger/post alarm images
Custom Alarms:
HTTP event servers and CGI events for setting customized alarm actions
Email/FTP Messaging:
Automatic transfer of stored images via email or FTP as event-triggered act ions
Pre
-alarm Buffer: 24 MB video buffer for JPEG snapshot images
Moxa VPort 26A-1MP Technical Specifications
D-3
Security
Password:
User level password protection
Filtering:
By IP address
Authentication:
802.1X
Encryption:
HTTPS, SSH
Environmental Limits
Operating Temperature:
Standard models:
-40 to 50°C (-40 to 122°F )
Wide temp. models:
-40 to 75°C (-40 to 167°F )
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidit y:
5 to 95% (non-condensing)
Altitude:
Up to 2000 m
Note: Please contact Moxa if you require products guaranteed to f
unction properly at higher altitudes.
Standards and Certifications
Safety:
UL 60950-1 (Pending)
EMI:
FCC Part 15, CISPR (EN 55022) class A
EMS:
EN 61000
-4-2 (ESD), Level 3,
EN 61000
-4-3 (RS), Level 3,
EN 61000
-4-4 (EFT), Level 3,
EN
61000-4-5 (Surge), Level 3,
EN 61000
-4-6 (CS), Level 3,
EN 61000
-4-8,
EN 61000
-4-11
Shock:
IEC 60068-2-27
Freefall:
IEC 60068-2-32
Vibration:
IEC 60068-2-6
Vandal Resistance:
EN 62262, IK10 level
MTBF
(mean time between failures)
Time:
201,721 hrs
Database:
Telcordia (Bellcore), 25°C
Warranty
Warranty Period:
5 years
Details:
See www.moxa.com/warranty
Minimum Viewing System Requirements
CPU:
Pentium 4, 2.4 GHz
Memory:
512 MB of memory
OS:
Windows XP with SP4 or above
Browser:
Internet Explorer 8.x or above
Multimedia:
DirectX 9.0c or above
Note: These preliminary specifications are subject to change without notice. Please check our website or sales
representative for the most up
-to-date specifications.
Software Bundled Free
VPort SDK PLUS:
Includes CGI commands, ActiveX Control, and API library for customized applications or
system integration for third third
-party developers (the latest version of SDK is available for download from
Moxa's website).
Standard:
OnVIF
Loading...