Moxa VP-IR2 Series User’s Manual
Second Edition, August 2014
www.moxa.com/product
© 2014 Moxa Inc. All rights reserved.
Moxa VP-IR2 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2014 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
+1-714-528-6777
Fax:
+1-714-528-6778
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia
-Pacific
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Before Getting Started
Before using your VP-IR2, read the following information:
The VP-IR2 is designed for the following applications:
1) For use with Moxa VPort series IP cameras to enhance night view images.
2) For use independently as an illuminator.
To prevent damage or problems caused by improper use, read this user’s manual before operating the
device and peripherals.
If you experience a system error, and the system cannot be recovered, please contact your local distributor.
Table of Contents
1. Introduction ...................................................................................................................................... 1-1
Package Checklist ............................................................................................................................... 1-1
Ordering Information .......................................................................................................................... 1-1
Physical Description ............................................................................................................................ 1-2
Dimensions (unit = mm) ..................................................................................................................... 1-2
2. Usage ................................................................................................................................................ 2-1
Installation ........................................................................................................................................ 2-1
Synchronization .................................................................................................................................. 2-2
A. Product Specifications ....................................................................................................................... A-1
1
1
1. Introduction
The VP-IR2 series IR illuminator is designed specifically to work with Moxa VPort series IP cameras. It features
high power efficiency and a long LED life cycle, and is suitable for all types of industrial surveillance applications.
The VP-IR2 can be easily mounted on a VPort camera housing.
Package Checklist
• VP-IR2 series IR illuminator
• Nut and bolt for mounting the VP-IR2 to a VPort camera housing
• Power and I/O cable
NOTE
Moxa’s
VP-IR2 Series is shipped with the mounting bracket attached to the body. When installing the VP-
IR2,
use an appropriate screw to attach the VP-IR2 mounting bracket to a wall, or use the provided nut and bolt to
attach the VP
-IR2 mounting bracket to an appropriate device or frame.
Ordering Information
Model Name Description
VP-IR22080 Infrared LED illuminator, 20°, 850 nm, 12 VDC, 60 to 100 m effective range
VP-IR26080 Infrared LED illuminator, 60°, 850 nm, 12 VDC, 20 to 50 meter effective range
NOTE
Check the model nam
e on the VP-IR2’s side label to verify that you received the model you ordered.
NOTE
This product must be installed in compliance with your local laws and regulations.
Moxa VP-IR2 Series Introduction
1-2
Physical Description
A: Protective Cover (made with PMMA material)
B: Main body
C: Mounting Bracket
D: Power & Signal I/O
Dimensions (unit = mm)
2
2. Usage
In this chapter, we describe how to install and synchronize the VP-IR2.
Installation
The VP-IR2 IR illuminator is usually used together with a Moxa CCTV camera. The VP-IR2 can be installed in the
following ways:
1. Mounted to a wall (use an appropriate screw)
The VP-IR2 comes with a mounting bracket (already attached) that can be mounted to a wall. Use an
appropriate screw to mount the unit to a wall and then connect the power and I/O cable to the camera that
the VP-IR2 will be used with.
2. Mounted to a pole (use an appropriate pole mount kit)
To mount the VP-IR2 to a pole, choose a pole mount adapter that is suitable for the size of the pole, and
then mount the VP-IR2 to the adapter.
3. Mounted to a VP camera housing and VPort camera
Use the nut and bolt included in the package to attach the VP-IR2 to a VP camera housing. The following
example illustrates how to install the VP-IR2 to a VP-CI701 housing and VP-CI800 bracket.
a. Install the VPort camera in the VP-CI701 camera housing.
b. Pull the VP-IR2’s power and I/O cable through the VP-CI800 bracket. The end of the cable with loose
electric wires should be pulled out from the top of the bracket, as illustrated in the following photograph.
c. Pull the wire end of the cable into VP-CI701 housing through the waterproof connector at the bottom of
the VP-CI701’s housing. Completely tighten the waterproof connector after the cable is pulled through.
d. Connect the wires to the camera as indicated below:
Black: to camera power connector V-
Red: to camera power connector V+
Blue: to camera DI ground
Yellow: to camera DI IN
Brown/Orange: Not used
Moxa VP-IR2 Series Introduction
1-2
Synchronization
To synchronize the VP-IR2’s auto on/off function with the camera’s Day/Night switch, connect the VP-IR2’s
relay output to the VPort camera’s input. Take the following steps to complete the configuration.
1. Open the Image Tuning page from the camera’s web browser interface and then configure the camera’s
Day/Night switch to D/I Control.
2. Connect the VP-IR2’s D/O to the camera’s D/I as described below:
Blue wire: to camera DI ground
Yellow wire: to camera DI IN
a. Close the VP-CI701’s housing and mount the VP-CI800’s bracket on the housing.
b. Install the housing and bracket to the desired surface.
Moxa VP-IR2 Series Introduction
1-3
c. Attach the VP-IR2 to the housing with the nut and bolt provided in the package.
NOTE
Be sure to
install the VP-IR2 onto the VP-CI701 housing and VP-CI800 bracket before you install it on the wall
.
NOTE
Follow the same process if you are installing
the VP-IR2 to another housing or camera.
A
A. Product Specifications
VP-IR2 Series
Infrared Wavelength 850 nm
Angle VP-IR22080: 20°
VP-IR26080: 60°
IR Effective Range VP-IR22080: 60 to 100 m
VP-IR26080: 20 to 50 m
Automatic IR On/Off Controlled by built-in photocell
Operating Temperature -30 to 60°C (-22 to 140°F)
IP Rating IP66
ICR Switching
Volt-free relay output
Power Consumption 12 W
Power Requirement 12 VDC
NOTE
You can mount multiple VP
-IR2 IR illuminators pointing in the same direction to increase the illuminated
distance and area
.
Loading...