2. Click Next to install the driver in the indicated folder.
3. Click Install to proceed with the installation.
1200/1400/1600
USB-to-Serial Hub
Quick Installation Guide
Third Edition, January 2007
1. Overview
UPort is the brand name of MOXA’s USB-to-serial product line, which
provides a wide range of products and solutions to extend Windows COM
ports using the PC’s USB port. Important features of UPort products
include support for hi-speed (480 Mbps) USB 2.0, Moxa CPU, Moxa
UART, the ability to assign COM port numbers, magnet accessories, and
mini female DB9 to terminal block. These features make the UPort
products easy to use and maintain.
The UPort 1200/1400/1600 line of USB-to-serial hubs includes the
following models:
• UPort 1250 2-port RS-232/422/485 USB-to-serial hub
• UPort 1250I
• UPort 1410 4-port RS-232 USB-to-serial hub
• UPort 1450 4-port RS-232/422/485 USB-to-serial hub
• UPort 1450I
• UPort 1610-8 8-port RS-232 USB-to-serial hub
• UPort 1650-8 8-port RS-232/422/485 USB-to-serial hub
• UPort 1610-16 16-port RS-232 USB-to-serial hub
• UPort 1650-16 16-port RS-232/422/485 USB-to-serial hub
Before connecting the UPort USB-to-serial hubs to your computer’s USB
port, we recommend installing the UPort driver first. To do this, follow
the installation procedure described in Section 3.
The installation procedure described in Section 3 was done on a PC
running Windows 2000 (x8 6). Windows XP and 2003 (32-bit and 64-bit)
driver installations are the same. UPort can be connected to any upstream
type A USB port that is on the PC host or on an upstream hub. UPort is
hot pluggable, and therefore there is no need to power down your
computer prior to installation.
After installing the driver, connect the UPort to an upstream host or hub.
The Found New Hardware wizard will locate the appropriate drivers
automatically. Once the drivers are found, various windows will pop up
as UPort’s serial port is being installed.
2-port RS-232/422/485 USB-to-serial hub w/
isolation protection
4-port RS-232/422/485 USB-to-serial hub w/
isolation protection
P/N:1802014000200
When the Found New Hardware wizard finishes installing UPort, use
the operating system’s Device Manager to check and/or modify the port
settings. The new COM port will be listed under Ports (COM & LPT).
2. Package Checklist
Before installing the UPort, verify that the package contains the following
items:
• UPort 1200/1400/1600 USB-to-serial hub
• 1 USB cable
• Document and Software CD-ROM
• UPort 1200/1400/1600 Quick Installation Guide
• Power adaptor (for UPort 1250I/1450I/1600-8) or power cord (for
UPort 1600-16)
Notify your sales representative if any of the above items are missing or
damaged.
3. Installing the UPort 1200/1400/1600 Driver
1. Run the Setup program located on the UPort 1200/1400/1600
Document and Software CD-ROM. Click Next to start installing the
driver.
— 1 — — 2 — — 3 —
4. The next window that opens cautions you that although this software
has not passed Windows logo testing, this driver has already been
tested and shown that it can support the Windows OS. Click Continue
Anyway to proceed. Then, click Finish to complete the driver
installation.
4. Installing the UPort 1200/1400/1600 Hardware
WARNING
1. This unit is not meant to be sold to consumers. It will only be shipped
to manufacturers or factories.
2. The DC source should come from a class 2 external adaptor or a 12 to
48 VDC Safety Extra-Low Voltage (SELV) limited power source
(LPS) using a transfer device.
3. This unit should be installed or set up by a qualified service person.
1. Refer to the table below to see if external power is needed for your
UPort. If applicable, connect the UPort to an external power source.
UPort
USBpowered
external
power
2. Connect the UPort to the PC using the USB cable.
3. After powering on your PC, Windows 2000/XP/2003 will
automatically detect the UPort.
UPort
UPort
UPort
UPort
UPort
1250
1250I
1410
1450
1450I
1600-8
√ × √ √ × × ×
× √ √ √ √ √ √
UPort
1600-16
4. Click Next to start the installation.
5. Select Install the software automatically (Recommended).
6. The next window that opens cautions you that although this software
has not passed Windows logo testing, this driver has already been
tested and shown that it can support Windows OS. Click Continue
Anyway to proceed. Then, click Finish to complete the driver
installation.
7. Repeat steps 4 to 6 until all COM ports are installed.
5. Serial Port Pin Assignments
The serial ports on the UPort 1200/1400/1600 have DB9 male connectors.
Refer to the following table for the RS-232 and RS-422/485 pin assignments.
DB9 Male
15
69
Power Input Specifications
UPort 1250: 5 VDC (bus power), 360 mA
UPort 1250I: 12 to 48 VDC, 200 mA (max. in 12 VDC)
UPort 1410/1450: 12 to 48 VDC (external) or 5 VDC (bus power),
UPort 1450I: 12 to 48 VDC, 360 mA (max. in 12 VDC)
UPort 1600-8: 12 to 48 VDC, 580 mA (max. in 12 VDC)
UPort 1600-16: 100 to 240 VAC,
Reproduction without permission is prohibited.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Pin RS-232
1 DCD TxD-(A) --2 RxD TxD+(B) --3 TxD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5 GND GND GND
6 DSR --- --7 RTS --- --8 CTS --- ---
260 mA (max. in 12 VDC)
220 mA (max. in 100 VAC)
Copyright © 2007
Moxa Technologies Co., Ltd.
All rights reserved.
RS-422/
4-wire RS-485
www.moxa.com
support@moxa.com
2-wire
RS-485
— 4 — — 5 — — 6 —