Moxa Technologies OnCell 5004, OnCell 5104 Quick Installation Manual

– 1 – – 2 – – 3 – - 4 -

P/N: 1802050040012

OnCell 5004/5104 Series

Quick Installation Guide

Third Edition, December 2011

Overview

The OnCell 5004/5104 series are high-performance industrial grade
cellular routers that allow up to 4 Ethernet-based devices to
simultaneously use a single cellular data account for primary or
backup network connectivity to remote sites and devices. Both
products provide the functionality of a cellular router, firewall, and
switch in on e single device . The difference between the OnCell 5004
and the 5104 series is that the OnCell 5104 comes with a built-in
relay output that can be configured to indicate the priority of events
to notify and warn engineer s in the field, and the two digital inputs
allow you to connect basic I/O devices, such as sensors, to the
cellular router. In addition, the OnCell 5104 has an IA design and can
be attached to a DIN-rail, whereas the OnCell 5004 can be placed on
a desktop or be wall-mounted. Both products use 12 to 48 VDC
power inputs with a screw-on connector for greater reliability, and
the Ethernet port comes with 1.5 KV magnetic isolation protection to
keep your system safe from unexpected electrical discharges.

Package Checklist

Before Installing the OnCell 5004/5104 series Cellular Router, verify
that the package contains the following items:

Standard Accessories

• Rubber SMA antenna

• Rubber stand (OnCell 5004 series only)

• Wallmount Kit (OnCell 5004 series only)

• Din-Rail Kit (OnCell 5104 series only)

• Terminal block (scre w type)

• Document and Software CD

• Product warranty statement

• Quick Installation Guide

Note: Please notify your sales representative if any of the above
items are missing or damaged.

Hardware Introduction

OnCell 5004 series

OnCell 5104 series

Reset Button

Press the Reset Button continuously for 5 sec to load factory default
settings. Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory default settings will be loaded once the
Ready LED stops blinking (default LAN IP: 192.168.127.254).

LED Indicators

The following table explains the LED indicators on the front panel of
the OnCell 5004/5104 series:

Type

Color

Meaning

PWR 1

Green

Activation of DC Power

Off

Power is off, or power error

condition exists.

PWR 2

Green

Activation of DC Power

Off

Power is off, or power error
condition exists.

2G
Amber

GPRS/EDGE is connected

Off

GPRS/EDGE is dis connected

3G

Amber

UMTS/HSDPA/HSPA is connected

Off

UMTS/HSDPA/HSPA is
disconnected

SIM 1
Amber

Steady on: SIM 1 is activated
Blinking: SIM 1 n ot inserted

Off

SIM 1 is inactivated

SIM 2

Amber

Steady on: SIM 2 is activated
Blinking: S IM 2 not inserted

Off

SIM 2 is inact ivated

Ready

Green

Steady on: Software Ready.

Blinking s lowly (1 sec): The On Cell
has been located by the OnCell
Search Utility.

off

Power is off, or is booting up.

Fault

Red

Steady on: Booting up, or IP fault.

Blinking s lowly (1 sec): Cannot get
an IP address from the DHCP server

off

Power is off, or there is no error

condition.

LAN 1-4
Green

Steady on: Software Ready.

Blinking s lowly (1 sec): Data

transmissi on

off

Power is off, or is booting up.

Signal (3 LEDs)

Green

Signal Level (at least 2 LEDs must
illuminated for data Transmission)

Connecting the I/O Port

The OnCell 5104/5104 series has six terminals on the terminal block
for the I/O ports, with 4 termina ls used for input, and 2 terminals
used for output.

Digital Inp ut—The power input level de termines the digital inp ut’s
ON/OFF state:

On: +13 to +30 V for state “1”
Off: -30 to +3 V for state “0”

Digital Output—1 relay output with current carrying capacity of 1 A
@ 24 VDC.

Hardware Installation Proce dure

STEP 1: Open the SIM cover, an d insert the SIM card into the SIM

card slot.

STEP 2: Connect the 12-48 VDC power adaptor to the OnCell
5004/5104 series and then plug the power adaptor into a DC outlet.

STEP 3: To configure the OnCell, use an Ethernet cable to connect
the OnCell’s LAN port directly to your computer’s Ethernet interface.

STEP 4: Connect the OnCell 5004/5104 series’ Ethernet port t o an
Ethernet enabled device.

Software Installation Inform ation

The Document & Software CD contains the User’s Manual, and the
OnCell Search Utility. Insert the CD and follow the on-screen
instructions. Please refer t o the User’s Manual for additional details
on using the OnCell Search Utility.

Pin Assignments and Cable Wi ring

Ethernet Port Pin Assignment

Pin

RS-232 1 TxD+ 2 TxD- 3 RxD+ 4 – 5 –

6

RxD- 7 –

8

–

Note: Please read Chapter 2: Getting Started in the OnCell
5004/5104 User’s Manual for more details about installation and
configuration.

Power Input and Relay Outp ut Pinouts

PIN

Name

Function

1

V1+

DC Power input 1

2

V1-

DC Power input 1

3

V2+

DC Power input 2

4

V2-

DC Power input 2

5 Relay Out

6

Relay Out

7

I1

Digital Inp ut

8

COM_1

Digital Inp ut GND

9

I2

Digital Inp ut

10

COM_2

Digital Inp ut GND

– 5 – – 6 – – 7 – - 8 -

www.moxa.com/support

The Americas:

[phone] (toll-free: 1-888-669-2872)

Europe:

[phone]

Asia-Pacific:

[phone]

China:

[phone] (toll-free: 800-820-5036)

 2010 Moxa Inc. All right s reserved.

Specifications

Cellular Interface(for OnCell 5004 & OnCell 5104)

Standards

GSM/GPRS

Band Options

Quad-band 850/900 and 1800/1900 MHz

GPRS Multi-slot
Class

Class 10

GPRS Termin al
Device Class

Class B

GPRS Coding
Schemes

CS1 to CS4
Tx Power

1 watt GSM 1800/1900, 2 watts EGSM 850/900

Cellular Interface (for OnCell 5004-HSDPA & 5104-HSDPA)

Standard

GSM/GPRS/EDGE/UMTS /HSDPA

Data Rate

UMTS (DL: 384Kbps, UL: 384Kbps)
HSDPA (DL: 3.6Mbps, UL: 386kbps)

Band Select ion

Tri-band 850/1900/2100 MHz
Quad-band 850/900/1800/1900 MHz

Cellular Interface (for OnCell 5004-HSPA & 5104-HSPA)

Standard

GSM/GPRS/EDGE/UMTS/HSDPA/HSPA+

Data Rate

UMTS (DL: 384Kbps, UL: 384Kbps)

HSDPA (DL: 3.6Mbps, UL: 386kbps)

HSPA+ (DL: 14.4Mbps, UL: 5.76Mbps )

Band Select ion

Five band 800/850/AWS/1900/2100 MHz
Quad-band 850/900/1800/1900 MHz

Tx Power:

1 watt GSM1800

2 watt GSM900

0.25 watt UMTS/HSDPA/HSPA+

0.5 watt EDGE900, 0.4 watt EDGE1800

GPRS Multi-slot
Class:

Class 12

GPRS Termin al
Device Class:

Class B

GPRS Coding
Schemes:

CS1 to CS4
SIM Control:

3V

WAN Interface

Number of
Ports 1 Ethernet

10/100 Mbps, RJ45 connector, Auto MDI/M DIX

Magnetic

Isolation

Protection

1.5 KV built-in

LAN Interface

Number of

Ports

4
Ethernet

10/100 Mbps, RJ45 connector, auto MDI/MDIX

Protection

Built-in 1.5 KV magnetic isolation

SIM Interface

Number of
SIMs

2
SIM Control

3V

I/O Interface (OnCell 5104 series only)

Alarm Contact

1 relay output with current carrying capacity of 1A
@ 24 VDC

Digital Inp uts

The power input level determines the digital input’s

ON/OFF state:
On: +13 to +30 V for state “1”

Off: -30 to +3 V for state “0”

Software

Network

Protocols

UDP, TCP, SNTP, ICMP, DDNS, DHCP/BOOTP,

PPPoE, PPP, DNS Relay, HTTPS, Telnet, RSTP,

IPSec

Router/Firewall

NAT, port forwarding, static routing

Authentication

Local user-name and password

Security

IP filtering

Physical Ch aracteristics

Housing

Aluminum, p roviding IP30 prote ction

Weight

OnCell 5004/5004 series: 505±5 g
OnCell 5104/5104 series: 645±5 g

Dimensions

OnCell 5004/5004 series: 158 x 103 x 34 mm
OnCell 5104/5104 series: 160 x 103 x 50 mm

Power Requirements

Number of
Power Inputs

1 terminal block, 1 power jack
Input Voltage

12 to 48 VDC

Data Link

OnCell 5004 series: 400 mA (idle) to 900 mA

(peak) @ 12 V
OnCell 5104 series: 450 mA (id le) to 950 mA

(peak) @ 12 V

Environmental Limits

Operating
temperature

-30 to 55°C (-22 to 131°F) , 5 to 95% RH

Storage
temperature

-40 to 75°C (-40 to 167°F)
Regulatory Approvals

EMC

CE Class A , FCC Class A, UL

Warranty

Warranty
Period

5 years