Moxa Technologies NPort 6650, NPort 6610 Quick Installation Manual

– 1 – – 2 – – 3 –

P/N: 1802066500015

*1802066500015*

NPort 6600 Series

Quick Installation Guide

Sixth Edition, August 2015

Overview

The NPort 6600 series of serial device servers includes 8-port,
16-port, and 32-port models for connecting larger numbers of
serial devices to Ethernet. Some applications now also require
better security when transmitting data through a network. The
NPort 6600 series of device servers use DES, 3DES, and AES data
encryption to provide secure network communication.

Package Checklist

Before Installing your NPort 6600 series secure device server,
verify that the package contains the following items:

• 1 NPort 6600 device server

• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male connection cable,
150 cm

• Power Cord (AC models only)

• 2 rack-mount ears

• Documentation and software CD

• Quick installation guide (printed)

• Warranty card

Optional Accessories

• DK-35A: 35 mm DIN-Rail Mounting Kit

• DIN-Rail Power Supply

• NM-TX01/NM-TX01-T: Network module with one
10/100BaseTX Ethernet port (RJ45 connector; supports
cascade redundancy)

• NM-FX01-S-SC/NM-FX01-S-SC-T: N etw ork module with one
100BaseFX single mode fiber port (SC connector; supports
cascade redundancy)

• NM-FX02-S-SC/NM-FX02-S-SC-T: N etw ork module with two
100BaseFX single mode fiber ports (SC connectors; supports
cascade redundancy)

• NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one
100BaseFX multi mode fiber port (SC connector; supports
cascade redundancy)

• NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two
100BaseFX multi mode fiber ports (SC connectors; supports
cascade redundancy)

NOTE: Please notify your sales representative if any of the above
items is missing or damaged.

Hardware Introduction

Demonstrated 8 port model to be an example.

Reset Button

Press the Reset button continuously for 5 sec to load factory
defaults: Use a pointed object to press the reset button. Release
the button after the Ready LED stops blinking.

RS-485 adjustable pull high/low resistor (150/1 kO)

The NPort 6650 has 3 DIP Switches associated with each serial port
for configuring the pull high/low resistors for RS-485 applications.
The switches are located in a recess on the bottom of the NPort

6650. To access the switches, first remove the panel covering the
recess.

SW
1 2 3

Pull High

Pull Low

Terminator

ON

1 KΩ

1 KΩ

120 KΩ

OFF

150 KΩ

150 KΩ

–

NOTE: For RS-232 applications, all DIP Switches for the port
should be set to the OFF position.

Rack Mounting

Use four screws to attach the NPort 6610/6650 to a standard rack

LED Indicators

Name

Color

Function

PWR

Red

Power is being supplied to the power input.

Ready

Red

Steady
on:

Power is on and the NPort 6600
series is booting up.

Blinking:

IP conflict, DHCP or BOOTP server

not responding, or relay output.
Check relay output first. If still
blinking, then there is an IP
conflict, or the DHCP or BOOTP

server did not respond properly.

Green

Steady

on:

Power is on and the NPort 6600

series is functioning normally.

Blinking: The device server has been

located by the Administrator’s

Locator function.

Off Power is off, or power error condition exists.

Link Orange 10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Off

Ethernet cable is disconnected, or has a
short.

P1-P16 Tx

Green

Serial port is transmitting data.

Off

No data is being transmitted through the
serial port

P1-P16 Rx

Orange

Serial port is receiving data..

Off

No data is being received through the serial
port.

FX

Orange

Steady
on:

Ethernet fiber connection, but port
is idle.

Blinking:

Fiber port is transmitting or
receiving data.

P1-P16

in-use
LEDs

Green

Serial port is opened by server side
software.

Off

Serial port is not opened by server side
software.

Alarm
Red

The relay Dout is open (exception)

Off

The relay Dout is Shorted (normal)

Module
Green

Network module is plugged in and detected

Off

No module present

LCM Display Panel

The NPort 6600 display panel will show the model name, server
name, and IP address when powered up

N P 6 6 1 0 _ 6 6 1 0 2 1 9 2 . 1 6 8 . 1 2 7 . 2 5 4

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

[phone] (toll-free: 1-888-669-2872)

Europe:

[phone]

Asia-Pacific:

[phone]

China:

[phone] (toll-free: 800-820-5036)

 2014 Moxa Inc., All Rights Reserved

Operating the LCM Panel

There are four push buttons on the NPort 6600’s top panel for
operating the server’s LCM panel. The function of each button is
described below:

Button

Action

MENU

Activates the main menu, or returns to a lower level.

∧

Scrolls up through a list of items shown on the LCM panel’s
second line.

∨

Scrolls down through a list of items shown on the LCM
panel’s second line.

SEL

Selects the option listed on the LCM panel’s second line.

Detailed LCM panel operating instructions can be found on the
Document and Software CD in the “NPort 6600 Series User’s
Manual.”

Note: LCM display panel and push buttons only for standard
temprature model

Hardware Installation Procedure

STEP 1: Connect the NPort 6600 device server to a suitable power

source.
AC models: Connect the 100 to 240 VAC power cord to the NPort
6600’s power input.
DC models: Connect the terminal block to a battery.

STEP 2: Connect the NPort 6600 series to a network. Use a
standard straight-through Ethernet cable to connect to a hub or
switch. Use a cross-over Ethernet cable when connecting to your
computer’s Ethernet port (e.g., when setting up or testing the
NPort 6600 server).

STEP 3: Connect the NPort 6600’s serial ports to your serial
devices.

Software Installation Information

NPort Search Utility

To install the NPort Search Utility, insert the NPort Document and
Software CD into your computer’s CD-ROM drive. When the NPort
Installation CD window opens, click on the Installation button, and
then follow the instructions on the screen. To view detailed
information about the NPort Search Utility, refer to the pdf version
of the “NPort 6600 Series User’s Manual,” which is located in the
document directory of the CD.

PComm Lite and Console Port (19200, 8, None, 1)

MOXA’s PComm Lite software utility is also included in the
Document and Software CD of the CD-ROM. PComm Lite is often
used to connect to the NPort 6600 through its console port to
configure the IP address for the first time. Use the following serial
console parameters when connecting through the console port:
19200, 8, None, 1.

Pin Assignments and Cable Wiring

Pin Assignments (NPort 6610/6650)

Pin RS-232

RS-422,

4-wire RS -485

2-wire RS-485

1

DSR – –

2

RTS

TxD+

–

3

GND

GND

GND

4

TxD

TxD-

–

5

RxD

RxD+

Data+

6

DCD

RxD-

Data-

7

CTS – –

8

DTR – –

Pin Mapping for RS-232 Cables (NPort 6610/6650)

NPort6610/6650

Serial Device

RJ45 DB9(M)

DB9(F)

DB25(M)

DB25(F)

DSR

1 6 4 6

20

DTR

RTS

2 7 8 4 5 CTS

GND

3 5 5 7 7 GND

TxD

4 3 2 2 3 RxD

RxD

5 2 3 3 2 TxD

DCD

6 1 1 8 8 DCD

CTS

7 8 7 5 4 RTS

DTR

8 4 6 20 6 DSR

Pin Mapping for RS-422/4W-RS-485 Cables (NPort 6650)

NPort 6650

Serial Device

RJ45 DB9(M)

DB9(F)

DB25(M)

DB25(F)

TxD+

2 7 8 4 5 RxD+

GND

3 5 5 7 7 GND

TxD-

4 3 2 2 3 RxD-

RxD+

5 2 3 3 2 TxD+

RxD-

6 1 1 8 8 TxD-

Pin Mapping for 2W-RS-485 Cables (NPort 6650)

NPort 6650

Serial Device

RJ45 DB9(M)

DB9(F)

DB25(M)

DB25(F)

GND

3 5 5 7 7 GND

Data+

5 2 3 3 2 Data+

Data-

6 1 1 8 8 Data-

Specifications

LAN

Ethernet Ports

10/100 Mbps (RJ45)

Protection

Built-in 1.5 KV magnetic isolation

Serial Interface

NPort 6610
NPort 6650

8, 16, or 32 RS-232 ports (8-pin RJ45)
8, 16, or 32 RS-232/422/485 ports (8-pin RJ45)

Signals

RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD,

GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485(2W): Data+, Data-, GND

RS-485(4W): Tx+, Tx-, Rx+, Rx-, GND

RS-485 Data
Direction

ADDC™ (Automatic Data Direction Control)
Serial Communication Parameters

Parity

None, Even, Odd, Space, Mark

Data bits

5, 6, 7, 8

Stop bit(s)

1, 1.5, 2

Flow control

RTS/CTS, XON/XOFF, DTR/DSR

Speed

50 bps to 921.6 Kbps

Console port

RS-232 console × 1

Memory Expansion Slot

Slot Type

SD socket (supports up to 2 GB)

Power Requirements

Power input

100 to 240 VAC, 47 to 63 Hz, 88 to 300 VDC,
±48 VDC (20 to 72 VDC, -20 to -72 VDC)

Alarm Contact

Relay output with current carrying capacity of 1A
@ 24 VDC

Mechanical Specifications

Material

SECC sheet metal (1 mm)

Dimensions
(W×D×H)

480×44×195 mm (including ears)
440×44×195 mm (without ears)

Operating Temperatures

Standard Temp. Models: 0 to 55°C (32 to 131°F)

Wide Temp. Models: -40 to 75°C (-40 to 167°F)

High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)

Storage Temperatures

Standard and Wide Temp. Models: -40 to 75°C (-40 to 167°F)
High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)

Regulatory Approvals

EMC

FCC Class A, CE Class A

Safety

UL, CUL, EN 60950-1