Moxa Technologies NPort 5600, NPort 5610, NPort 5630, NPort 5650 Quick Installation Manual

— 1 — — 2 — — 3 —

NPort 5610/5630/5650 Series

Quick Installation Guide

Second Edition, July 2006

1. Overview

Welcome to the MOXA NPort 5600 Series. NPort 5610-16/8 has 16 or 8
RS-232 ports, NPort 5630-16/8 has 16 or 8 RS-422/485 ports, and NPort
5650-16/8 have 16 or 8 RS-232/422/485 ports.

2. Package Checklist

The NPort 5600 package should contain the following items:

y 1 16-port or 8-port serial device server
y NPort Documentation & Software CD
y NPort 5600 Quick Installation Guide
y Power cord (included with AC version of the product)

Optional Accessories

y CBL-RJ45M9-150:
y CBL-RJ45F9-150:
y CBL-RJ45M25-150:
y CBL-RJ45F25-150:

8-pin RJ45 to Male DB9 cable, 150 cm
8-pin RJ45 to Female DB9 cable, 150 cm
8-pin RJ45 to Male DB25 cable, 150 cm
8-pin RJ45 to Female DB25 cable, 150 cm

Notify your sales rep if any of the above items are missing or damaged.

3. Hardware Introduction

The NPort 5600 Series has 12 models: NPort 5610-16, NPort 5610-8,
NPort 5610-16-48V, NPort 5610-8-48V, NPort 5630-16, NPort 5630-8,
NPort 5650-8, NPort 5650-16, NPort 5650-8-M-SC,
NPort 5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.
The front and rear panels are shown below:

Front panel of NPort 5600 Series

5610-

16

Rear panel of NPort 5610/5630/5650 (AC Power)

LAN

Serial ports

ACPOWER100-240V, 47-63Hz

12345678

910111213141516

Rear panel of NPort 5650 (Fiber Model)

Serial ports

Link

Fiber

ACPOWER100-240V, 47-63Hz

12345678

910111213141516

Rear panel of NPort 5610-16-48V (DC Power)

LAN

Serial ports

12345678

910111213141516

V+ V-

ON OFF

Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object to press the reset button. Release

the button after the Ready LED stops blinking.
LED Indicators on the Front Panel

The front panels of NPort 5600 have several LED indicators, as described
in the following table.

LED Name LED Color LED Function

Off Power is off, or power error condition exists.

Steady on: Power is on and NPort is

booting up.

Red

Blinking: Indicates an IP conflict, or that

DHCP or BOOTP server did
not respond properly.

Steady on: Power is on and NPort is

functioning normally.

Ready

Green

Blinking: The NPort has been located by

NPort Administrator’s
Location function.

Orange Serial port is receiving data.

Green Serial port is transmitting data.

1-16

Off

No data is being transmitted or received
through the serial port.

LCM Display Panel—If the NPort is working properly, the LCM panel
will be colored green. The red Ready LED will also light up, indicating
that the NPort is receiving power. After the red Ready LED turns green,
you will see a display similar to:

N P 5 6 1 0 - 1 6 _ 3 8
1 9 2 . 1 6 8 . 1 2 7 . 2 5 4

y NP5610-16 is the NPort’s name
y 38

is the NPort’s serial number

y 192.168.127.254 is the NPort’s IP address

LCM Panel Operation—There are four buttons on NPort 5600’s front
panel. These buttons are used to operate the server’s LCM panel. Going
from left to right, the buttons are:

Button Action

MENU

Activates the main menu, or returns to an upper level.
Scrolls up through a list of items shown on the LCM panel’s
second line.
Scrolls down through a list of items shown on the LCM panel’s
second line.

SEL

Selects the option listed on the LCM panel’s second line.

Detailed LCM Panel Operating instructions can be found on the
CD-ROM in the NPort 5600 Series User’s Manual.

Link Indicator on the Rear Panel of NPort 5650 Fiber Model

The rear panels of NPort 5600 have a link indicator, as described in the
following table.

LED Name LED Color LED Function

Off Fiber is disconnected

Green

Fiber is connected and no data is being
transmitted

Link

Blinking

Fiber is connected and data is being
transmitted

4. Hardware Installation Procedure

STEP 1: After removing NPort 5600 from the box, the first thing you

should do is attach the power adaptor.
STEP 2: Connecting the Power
AC: Connect the NPort 5610/5630/5650 100 to 240 VAC power cord to

the AC connector. If the power connection is correct, the “Ready”
LED will glow solid red until the system is ready, at which time the
“Ready” LED will change to green.

DC: Connect NPort 5610-16/8-48V’s power cord to the DC connector,

and then perform the following:

V+ V-

ON OFF

1. Loosen the screws on the V+ and V- terminals of

NPort 5610-16/8-48V’s terminal block.

2. Connect the power cord’s 48 VDC or -48 VDC

wire to the terminal block’s V

+

terminal, and the
power cord’s DC Power Ground wire to the
terminal block’s V

-

terminal, and then tighten the
terminal block screws. (Note: NPort
5610-16/8-48V can still operate even if the
48V/-48V and DC Power Ground are reversed.)

If the power is connected properly, the “Ready” LED will glow a solid
red until the system is ready, at which time the “Ready” LED will change
to green.

Grounding NPort 5610-16/8-48V:

V+ V-

SG

ON OFF

Grounding and wire routing help limit the effects
of noise due to electromagnetic interference
(EMI). Run the ground connection from the
ground screw to the grounding surface prior to
connecting devices. The Shielded Ground
(sometimes called Protected Ground) contact is
the second contact from the right of the 5-pin
power terminal block connector located on the
rear panel of NPort 5610-16/8-48V. Connect the
SG wire to the Earth ground.

STEP 3: Connect NPort 5600 to a network. Use a standard
straight-through Ethernet cable to connect to a Hub or Switch. When
setting up or testing NPort 5600, you might find it convenient to connect
directly to your computer’s Ethernet port. In this case, use a cross-over
Ethernet cable.

STEP 4: Connect NPort 5600’s serial port to a serial device.
Placement Options: You can place NPort 5600 on a desktop or other

horizontal surface.

P/N: 1802056000200

— 4 — — 5 — — 6 —

5. Software Installation Information

To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort
Installation CD window opens, click the INSTALL UTILITY button,

and then follow the instructions on the screen.
To view detailed information about NPort Administration Suite, click

the DOCUMENTS button, and then select “NPort 5600 Series User’s
Manual” to open the pdf version of this user’s guide.

6. Pin Assignments and Cable Wiring

Serial Port Pinouts
for NPort 5610

Serial Port Pinouts for NPort 5630

18

18

Pin RS-232

1 DSR (in)
2 RTS (out)
3 GND
4 TxD (out)
5 RxD (in)
6 DCD (in)
7 CTS (in)
8 DTR (out)

Pin

RS-422

4-wire RS-485

2-wire RS-485

1 --- --­2 --- --­3 TxD+ --­4 TxD- --­5 RxD- Data­6 RxD+ Data+
7 GND GND
8 --- ---

Serial Port Pinouts for NPort 5650

Pin RS-232

RS-422

4-wire RS-485

2-wire

RS-485

1 DSR --- --­2 RTS TxD+ --­3 GND GND GND
4 TxD TxD- --­5 RxD RxD+ Data+
6 DCD RxD- Data­7 CTS --- --­8 DTR --- ---

18

Serial Cables for NPort 5630 (2-wire RS-485)

RJ45 Port DB9-M DB9-F DB25-M DB25-F Serial Port

NPort 5630

Serial
Device

Data- 5

2 3 3 2 Data-

Data+ 6

1 1 8 8 Data+

GND 7

8 7 5 4 GND

Serial Cables for NPort 5630 (RS-422/4-wire RS-485)

RJ45 Port DB9-M DB9-F DB25-M DB25-F Serial Port

NPort 5630

Serial
Device

TxD+ 3

5 5 7 7 RxD+

TxD- 4

3 2 2 3 RxD-

RxD- 5

2 3 3 2 TxD-

RxD+ 6

1 1 8 8 TxD+

GND 7

8 7 5 4 GND

Serial Cables for NPort 5610/5650 (RS-232)

RJ45 Port DB9-M DB9-F DB25-M DB25-F Serial Port

NPort 5610
NPort 5650

Serial
Device

DSR 1

6 4 6 20 DTR

RTS 2

7 8 4 5 CTS

GND 3

5 5 7 7 GND

TxD 4

3 2 2 3 RxD

RxD 5

2 3 3 2 TxD

DCD 6

1 1 8 8 DCD

CTS 7

8 7 5 4 RTS

DTR 8

4 6 20 6 DSR

Serial Cables for NPort 5650 (RS-422/4-wire RS-485)

RJ45 Port DB9-M DB9-F DB25-M DB25-F Serial Port

NPort 5650

Serial
Device

TxD+ 2

7 8 4 5 RxD+

GND 3

5 5 7 7 GND

TxD- 4

3 2 2 3 RxD-

RxD+ 5

2 3 3 2 TxD+

RxD- 6

1 1 8 8 TxD-

Serial Cables for NPort 5650 (2-wire RS-485)

RJ45 Port DB9-M DB9-F DB25-M DB25-F Serial Port

NPort 5650

Serial
Device

GND 3

5 5 7 7 GND

Data+ 5

2 3 3 2 Data+

Data- 6

1 1 8 8 Data-

7. Environmental Specifications

LAN

Ethernet
Protection

10/100 Mbps, RJ45
Built-in 1.5 KV magnetic isolation

Optical Fiber

Multi mode Single mode

Distance 0 to 2 km, 1310 nm

(62.5/125 μm, 500
MHz*km)

0 to 40 km, 1310 nm
(9/125 μm, 3.5 PS/
(nm*km))

Min. TX Output -20 dBm 0 to 40 km, -5 dBm
Max. TX Output -14 dBm 0 to 40 km, 0 dBm
Sensitivity -34 to -30 dBm -36 to -32 dBm

Serial Interface

Interface
No. of Ports
Port Type
Signals (RS-232)
Signals (RS-422)
Signals (2-wire RS-485)
Signals (4-wire RS-485)
Serial Line Protection
RS-485 Data Direction

RS-232/422/485
16/8
8-pin RJ45
TxD, RxD, RTS, CTS, DTR, DSR, DCD,
GND
Tx+, Tx-, Rx+, Rx­Data+, Data-, GND
Tx+, Tx-, Rx+, Rx­15 KV ESD for all signals
ADDC™ (Automatic Data Direction Control)

Power requirements

Power Input

Power Consumption

NPort 5610-8/16
NPort 5610-8/16-48V
NPort 5630-8/16
NPort 5650-8/16
NPort 5650-S-SC-8/16
NPort 5650-M-SC-8/16

100 to 240 VAC, 47 to 63 Hz,
±48 VDC (38 to 72 VDC, -38 to -72 VDC)

141 mA @ 100 VAC, 93 mA @ 240 VAC
135 mA @ 48 VDC
152 mA @ 100 VAC, 98 mA @ 240 VAC
158 mA @ 100 VAC, 102 mA @ 240 VAC
164 mA @ 100 VAC, 110 mA @ 240 VAC

174 mA @ 100 VAC, 113 mA @ 240 VAC
Operating temp. 0 to 55°C (32 to 131°F)
Operating humidity 5 to 95% RH
Dimensions (W×D×H) 190 × 44.5 × 478 mm (including ears)

190 × 44.5 × 440 mm (without ears)
Serial line protection 15 KV ESD for all signals
Magnetic isolation 1.5 KV for Ethernet
Power line protection 4 KV Burst (EFT), EN61000-4-4

2 KV Surge, EN61000-4-5
Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

Copyright © 2006

Moxa Technologies Co., Ltd.

All rights reserved.

Reproduction without permission is prohibited.

Tel: [phone]

www.moxa.com

Fax: [phone]

[e-mail]