Moxa Technologies NPort 5610-16, NPort 5610-8, NPort 5610-16-48V, NPort 5610-8-48V, NPort 5630-8 Quick Installation Manual

— 1 — — 2 — — 3 —

NPort 5600 Series

Quick Installation Guide

Fourth Edition, August 2004

1. Overview

Welcome to the MOXA NPort 5600 Series of advanced serial device servers,
which make it easy for you to network-enable your serial devices. NPort
5610-16/8 comes with 16/8 RS-232 ports, and NPort 5630-16/8 comes with
16/8 RS-422/485 ports.

2. Package Checklist

Before installing NPort 5600, verify that the package contains the following
items:

y 1 16-port or 8-port serial device server
y NPort Documentation & Software CD
y NPort 5600 Quick Installation Guide
y Power cord (included with AC version of the product)

Optional Accessories

y CBL-RJ45M9-150
y CBL-RJ45F9-150
y CBL-RJ45M25-150
y CBL-RJ45F25-150

8-pin RJ45 to Male DB9 cable, 150 cm
8-pin RJ45 to Female DB9 cable, 150 cm
8-pin RJ45 to Male DB25 cable, 150 cm
8-pin RJ45 to Female DB25 cable, 150 cm

Notify your sales representative if any of the above items is missing or
damaged.

3. Hardware Introduction

The NPort 5600 Series has 6 models: NPort 5610-16, NPort 5610-8, NPort
5610-16-48V, NPort 5610-8-48V, NPort 5630-16, and NPort 5630-8. The
following figures show the front and rear panel of NPort 5600.
Front panel of NPort 5600 Series

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Tx

Rx

Ready

MENU SEL

5610-16-48V

Reset

Rear panel of NPort 5610-16 (AC Power)

23456789

12345678

Serial ports

O

I

13 14 15 169 101112

LAN

AC POWER 100-240V, 47-63 Hz

Rear panel of NPort 5610-16-48V (DC Power)

23456789

12345678

Serial ports

13 14 15 169 101112

LAN

V+ V-

ON OFF

Reset Button—Press the Reset button continuously for 5 sec to load factory

defaults: Use a pointed object, such as a straightened paper clip or toothpick,

to press the reset button. This will cause the Ready LED to blink on and off.

The factory defaults will be loaded once the Ready LED stops blinking (after

about 5 seconds). At this point, you should release the reset button.

LED Indicators

The front panels of NPort 5600 have several LED indicators, as described in
the following table.

LED Name LED Color LED Function

off Power is off, or power error condition exists.

Steady on: Power is on and NPort is

booting up.

red

Blinking: Indicates an IP conflict, or

DHCP or BOOTP server did
not respond properly.

Steady on: Power is on and NPort is

functioning normally.

Ready

green

Blinking: The NPort has been located by

NPort Administrator’s
Location function.

orange

Serial port is receiving data.

green

Serial port is transmitting data.

1-16

off

No data is being transmitted or received
through the serial port.

LCM Display Panel—If the NPort is working properly, the LCM panel will
display a green color. The red Ready LED will also light up, indicating that
the NPort is receiving power. After the red Ready LED turns green, you will
see a display similar to:

NP5610-16_38

192. 168.127. 2 54

This is where

z NP5610-16 is the NPort’s name
z 38

is the NPort’s serial number

z 192.168.127.254 is the NPort’s IP address

LCM Panel Operation—There are four buttons on NPort 5600’s front panel.
These buttons are used to operate the server’s LCM panel. Going from left to
right, the buttons are:

Button Action

MENU

Activates the main menu, or returns to an upper level.
Scrolls up through a list of items shown on the LCM
panel’s second line.
Scrolls down through a list of items shown on the LCM
panel’s second line.

SEL

Selects the option listed on the LCM panel’s second line.

Detailed LCM Panel Operating instructions can be found on the CD-ROM in
the “NPort 5600 Series User’s Manual.”

4. Hardware Installation Procedure

STEP 1: After removing NPort 5600 from the box, the first thing you should

do is attach the power adaptor.

STEP 2: Connecting the Power

AC: Connect the NPort 5610/5630 100-240 VAC power cord to the AC

connector. If the power connection is correct, the “Ready” LED will
show a solid red color until the system is ready, at which time the
“Ready” LED will change to a green color.

DC: Connect NPort 5610-16/8-48V’s power cord to the DC connector, and

then follow the steps given below:

V+ V-

ON OFF

1. Loosen the screws on the V+ and V- terminals of
NPort 5610-8/16-48V’s terminal block.

2. Connect the power cord’s 48 VDC or -48 VDC wire
to the terminal block’s V

+

terminal, and the power
cord’s DC Power Ground wire to the terminal block’s
V

-

terminal, and then tighten the terminal block
screws. (Note: NPort 5610-8/16-48V can still operate
even if the 48V/-48V and DC Power Ground are
reversed.)

If the power is connected properly, the “Ready” LED will show a solid red
color until the system is ready, at which time the “Ready” LED will change to
a green color.

Grounding NPort 5610-16/8-48V:

V+ V-

SG

ON OFF

Grounding and wire routing helps limit the effects of
noise due to electromagnetic interference (EMI). Run
the ground connection from the

ground screw to the

grounding surface prior to connecting devices. The
Shielded Ground (sometimes called Protected
Ground) contact is the second contact from the right
of the 5-pin power terminal block connector located
on the rear panel of NPort 5610-8/16-48V. Connect
the SG wire to the Earth ground.

STEP 3: Connect NPort 5600 to a network. Use a standard straight-through
Ethernet cable to connect to a Hub or Switch. When setting up or testing
NPort 5600, you might find it convenient to connect directly to your
computer’s Ethernet port. In this case, use a cross-over Ethernet cable.

STEP 4: Connect NPort 5600’s serial port to a serial device.

Placement Options: You can place NPort 5600 on a desktop or other

horizontal surface.

P/N: 18020561002

— 4 — — 5 — — 6 —

5. Software Installation Information

To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort
Installation CD window opens, click on the INSTALL UTILITY button,

and then follow the instructions on the screen.

To view detailed information about NPort Administration Suite, click on
the DOCUMENTS button, and then select “NPort 5600 Series User’s
Manual” to open the pdf version of this user’s guide.

6. Pin Assignments and Cable Wiring

Serial Port RS-232 Pinouts (RJ45)

1

8

Pin

1
2
3
4
5
6
7
8

Signal

DSR (in)
RTS (out)
GND
TxD (out)
RxD (in)
DCD (in)
CTS (in)
DTR (out)

Serial Port RS-422/4-wire RS-485 Pinouts (RJ45)

1 8

Pin

1
2
3
4
5
6
7
8

Signal

RxD­RxD+
GND

---

---

---

TxD+
TxD-

Serial Port 2-wire RS-485 Pinouts (RJ45)

1 8

Pin

1
2
3
4
5
6
7
8

Signal

Data-

Data+

GND

---

---

---

---

---

Serial Cables

RJ45 (8-pin) to Female DB9, for NPort 5610

NPort 5610

8 pins 9 pins

DSR

RTS

GND

TxD
RxD

DCD

CTS

DTR

RS-232
Device

DTR
CTS
GND
RxD
TxD
DCD
RTS
DSR

Cable Wiring

1
2
3
4
5
6
7
8

4
8
5
2
3
1
7
6

RJ45 Connector DB9 FemaleRJ45 Port DB9 Mal

e

RJ45 (8-pin) to Male DB9, for NPort 5610

NPort 5610

8 pins 9 pins

DSR

RTS

GND

TxD
RxD

DCD

CTS

DTR

RS-232
Device

DTR
CTS
GND
RxD
TxD
DCD
RTS
DSR

Cable Wiring

1
2
3
4
5
6
7
8

6
7
5
3
2
1
8
4

RJ45 Connector DB9 MaleRJ45 Port DB9 Female

RJ45 (8-pin) to Female DB25, for NPort 5610

NPort 5610

8 pins 25 pins

DSR

RTS

GND

TxD
RxD

DCD

CTS

DTR

RS-232
Device

DTR
CTS
GND
RxD
TxD
DCD
RTS
DSR

Cable Wiring

1
2
3
4
5
6
7
8

20

5
7
3
2
8
4
6

RJ45 Connector DB25 Female

RJ45 Port DB25

Male

RJ45 (8-pin) to Male DB25, for NPort 5610

NPort 5610

8 pins 25 pins

DSR
RTS

GND

TxD

RxD
DCD
CTS
DTR

RS-232
Device

DTR
CTS
GND
RxD
TxD
DCD
RTS
DSR

Cable Wiring

1
2
3
4
5
6
7
8

6
4
7
2
3
8
5

20

RJ45 Connector DB25 Male

RJ45 Port DB25

Female

7. Environmental Specifications

Power requirements

Power Input

Power Consumption

NPort 5610-8/16
NPort 5610-8/16-48V
NPort 5630-8/16

100 to 240 VAC, 47 to 63 Hz,
±48 VDC (38 to 72 VDC, -38 to -72 VDC)

200 mA for 100V, 145 mA for 240V
250 mA (at 48V max.)

212 mA for 100V, 130 mA for 240V
Operating temp. 0 to 55°C (32 to 131°F)
Operating humidity 5 to 95% RH
Dimensions (W×D×H)

198 × 45 × 480 mm (including ears)

198 × 45 × 440 mm (without ears)
Serial line protection 15 KV ESD for all signals
Magnetic isolation 1.5 KV for Ethernet
Power line protection

4 KV Burst (EFT), EN61000-4-4

2 KV Surge, EN61000-4-5
Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

Copyright  2004

Moxa Technologies Co., Ltd.

All rights reserved.

Reproduction without permission is prohibited.

Tel: [phone]
Fax: [phone]
www.moxa.com
[e-mail]