Moxa Technologies NPort 5610-16/8, NPort 5610-8/16-48V, NPort 5630-8/16-48V, NPort 5630-16/8 Quick Installation Manual

5600 Series

Quick Installation Guide

Third Edition, November 2003

1. Overview

Welcome to MOXA NPort 5600 Series of advanced serial device servers that
make it easy to network-enable your serial devices. NPort 5610-16/8 comes
with 16/8 RS-232 ports, and NPort 5630-16/8 comes with 16/8 RS-422/485
ports.

2. Package Checklist

Before installing NPort 5600, verify that the package contains the following
items:

y 1 16-port or 8-port serial device server
y NPort Documentation & Software CD
y NPort 5600 Quick Installation Guide
y Power cord

Optional Accessories

y CBL-RJ45M9-150
y CBL-RJ45F9-150
y CBL-RJ45M25-150
y CBL-RJ45F25-150

RJ45 8-pin to DB9 Male cable, 150 cm
RJ45 8-pin to DB9 Female cable, 150 cm
RJ45 8-pin to DB25 Male cable, 150 cm
RJ45 8-pin to DB25 Female cable, 150 cm

Notify your sales representative if any of the above items is missing or
damaged.

3. Hardware Introduction

The NPort 5600 Series has 8 models: NPort 5610-16, NPort 5610-8, NPort
5610-16-48V, NPort 5610-8-48V, NPort 5630-16, NPort 5630-8, NPort
5630-16-48V, and NPort 5630-8-48V. The following figures shows the front
and rear panel of NPort 5600.

Front panel of NPort 5600 Series

Rear panel of NPort 5610-16 (AC Power)

Rear panel of NPort 5610-16-48V (DC Power)

Reset Button—Press the Reset button continuously for 5 sec to load factory

defaults: Use a pointed object, such as a straightened paper clip or toothpick,
to press the reset button. This will cause the Ready LED to blink on and off.
The factory defaults will be loaded once the Ready LED stops blinking (after
about 5 seconds). At this point, you should release the reset button.

LED Indicators

The front panels of NPort 5600 have several LED indicators, as described in
the following table.

LED Name LED Color LED Function

off Power is off, or power error condition exists.

Steady on: Power is on and NPort is

booting up.

red

Blinking: Indicates an IP conflict, or

DHCP or BOOTP server did
not respond properly.

Steady on: Power is on and NPort is

functioning normally.

Ready

green

Blinking: The NPort has been located by

NPort Administrator’s
Location function.

orange

Serial port is receiving data.

green

Serial port is transmitting data.

1-16

off

No data is being transmitted or received
through the serial port.

LCM Display Panel—If the NPort is working properly, the LCM panel will
display a green color. The red Ready LED will also light up, indicating that
the NPort is receiving power. After the red Ready LED turns green, you will
see a display similar to:

NP5610-16_38
1 9 2 . 1 6 8 . 1 2 7 . 2 5 4

This is where

z NP5610-16 is the NPort’s name
z 38

is the NPort’s serial number

z 192.168.127.254 is the NPort’s IP address

LCM Panel Operation—There are four buttons on NPort 5600’s front panel.
These buttons are used to operate the server’s LCM panel. Going from left to
right, the buttons are:

Button Action

MENU

Activates the main menu, or returns to an upper level.
Scrolls up through a list of items shown on the LCM

panel’s second line.
Scrolls down through a list of items shown on the LCM
panel’s second line.

SEL

Selects the option listed on the LCM panel’s second line.

Detailed LCM Panel Operating instructions can be found on the CD-ROM in
the “NPort 5600 Series User’s Manual.”

4. Hardware Installation Procedure

STEP 1: After removing NPort 5600 from the box, the first thing you should

do is attach the power adaptor.

STEP 2: Connect NPort 5600 to a network. Use a standard straight-through
Ethernet cable to connect to a Hub or Switch. When setting up or testing
NPort 5600, you might find it convenient to connect directly to your
computer’s Ethernet port. In this case, use a cross-over Ethernet cable.

STEP 3: Connect NPort 5600’s serial port to a serial device.

Placement Options: You can place NPort 5600 either on a desktop or other

horizontal surface.

—1—

—2—

—3—

5. Software Installation Information

To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort
Installation CD window opens, click on the INSTALL UTILITY button,

and then follow the instructions on the screen.

To view detailed information about NPort Administration Suite, click on
the DOCUMENTS button, and then select “NPort 5600 Series User’s
Manual” to open the pdf version of this user’s guide.

6. Pin Assignments and Cable Wiring

Serial Port Pinouts

Serial Port 4-wire RS-422 Pinouts (RJ45)

Serial Port 2-wire RS-485 Pinouts (RJ45)

Serial Cables

RJ45 (8 pins) to DB9 Female, for NPort 5610

RJ45 (8 pins) to DB9 Male, for NPort 5610

RJ45 (8 pins) to DB25 Female, for NPort 5610

RJ45 (8 pins) to DB25 Male, for NPort 5610

7. Environmental Specifications

Power requirements

Power Input
Power Consumption

NPort 5610-8/16
NPort 5610-8/16-48V
NPort 5630-8/16
NPort 5630-8/16-48V

100 to 240 VAC, 47 to 63 Hz, or 12-48 VDC
200 mA for 100V, 130 mA for 240V
190 mA (at 48V max.)
212 mA for 100V, 130 mA for 240V
215 mA (at 48V max.)

Operating temp. 0 to 55°C (32 to 131°F)
Operating humidity 5 to 95% RH
Dimensions (W×D×H)

190 × 44.5 × 478 mm (including ears)

190 × 44.5 × 440 mm (without ears)
Serial line protection 15 KV ESD for all signals
Magnetic isolation 1.5 KV for Ethernet
Power line protection

4 KV Burst (EFT), EN61000-4-4

2 KV Surge, EN61000-4-5
Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

Copyright  2003

Moxa Technologies Co., Ltd.

All rights reserved.

Reproduction without permission is prohibited.

Tel: [phone]
Fax:[phone]
www.moxa.com
[e-mail]

P/N: 18020561001

—5— —4—

—6—