Moxa Technologies Media Converter User Manual
Media Converter User’s Guide
Second Edition, June 2008
1. Overview
MOXA Media Converter is a standalone physical layer device that
converts between 10/100BaseT(X) and 100BaseFX segments of the
same network. The converter supports Link Fault Pass-through for
easily tracing network link failures, and the LFP function enhances the
integrity and conformity of TP-Fiber linking to make the network
easier to maintain. ME51 is powered by an external power adaptor or
USB port on the hosting device (e.g., PC or NB). The option of using
USB port power, which is unique to ME51 for products of this type,
offers greater flexibility when deploying ME51 in the field.
2. Package Checklist
MOXA ME51 products are shipped with the following items:
• 1 ME51-M-SC, 1 ME51-M-ST or 1 ME-S-SC
• AC-DC Power Adapter
• ME51 User's Manual
Please notify your sales representative immediately if any of the above
items is missing or damaged
3. Model Description
ME51-M-SC: 10/100BaseT(X) to 100BaseFX media converter;
multi mode, SC type fiber connection
ME51-M-ST: 10/100BaseT(X) to 100BaseFX media converter;
multi mode, ST type fiber connection
ME51-S-SC: 10/100BaseT(X) to 100BaseFX media converter;
single mode, SC type fiber connection
Panel Layout of ME51 series
• Front Panel View
• Side Panel View
• Rear Panel View
4. Wiring the Power Inputs
Ä Note: The Media Converter is hot-swappable.
Wear a grounding device for electrostatic discharge
ME51 with AC-DC Power Adapter
1. Enabled power source from AC-DC Power Adapter by dip switch
setting(Refer to Chapter 6 dip switch setting)
2. Verify that the AC-DC adapter conforms to your country
AC power requirement and then insert the power plug
3. Connect ME51 for network connection.
ME51 with Self Powering Cable (USB)
Enable power source from USB by dip switch setting (Refer to Chapter
6 dip switch setting)
Ä Note: Please ensure that the dip switch is on the right side of
slide switch
Install USB cable. Plug type A connector in PC(NB)'s USB port(jack)
and type B connector in the ME51’s USB port (See Fig. 1)
Install the media cable for network connection
Warning:
Please make sure that the power of PC/NB is
turned on, or else the ME51 will not work.
ME51 with USB power source(Type B-to-Type A Plug) and
FX/TP connection
5. Communication Connection
ME51 models have one 10/100BaseT(X) Ethernet port, and one 100
BaseFX (SC or ST type connector) fiber port.
5.1 10/100BaseT(X) Ethernet Port Connection
ME51 supports auto MDI/MDI-X. Below we show pinout s for b oth MDI
(NIC-type) ports and MDI-X (HUB/Switch-type) ports, a nd also show
cable wiring diagrams for straight-thro ugh and cr oss-ov er Ether net cables.
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring
FDX
/
COL
LNK
/
ACT
1
00
FX TP
TX RX
Bridge Media Converter
10/100Base-TX to 100Base-FX
PWR
FDX
LFP
FDX
100
A
UTO
S1
HDX-FX
LFP DIS
HDX
10
FORCE
1 2 3 4 5
TP
100FX Fiber
Network
USB B Type Jack
RJ-45 Jack
Cat. 5 Cable
USB Cable
Fiber Optic
USB A Type Jack
10/100 Ethernet
Switch/NIC
—1— —2— —3—
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring
6. Dip Switch Settings
Power inputs settings
Enabled power source
from AC-DC Power
Adapter
Enabled power source
from USB
Communication setting
FDX FX at full duplex (default)
FX
HDX FX at half duplex
LFP
Enable Link Fault Pass-Through
LFP DIS
Disable Link Fault Pass-Through
FDX
TP at full duplex (default)
HDX
TP at half duplex when TP at Force
100
TP at 100M (default)
TP
10
TP at 10M when TP at Force
7. Link Fault Pass Through
ÄNote: Link fault pass through (LFP) function will be enabled by dip
switch setting. Disable LFP function by setting dip switch to LLFP
DIS.
This media converter supports link fault pass through (LFP) in
TX/FX converter application. Link status on one port is
propagated to the other port to notify the remote nodes. If TP port
is unplugged, this converter stops transmission on fiber port. This
causes the remote fiber node link to fail. LED shows the link failure
on both TP and fiber ports. If fiber link fails, this converter restarts
auto-negotiation on TP port but always stays in the link failure
state. This causes the remote TP node link to fail. LED also shows
the link failure on both TP and fiber ports. Below shown the
normal status when the link is successful connected and the
erroneous status when TP Cable A, Fiber Cable B or Fiber Cable C
fails to connect.
Normal status via a pair of LFPs
The status as TP Cable A is broken
The status as Fiber Cable B or C is broken
Note : ● indicates LNK/ACT LED Lit
○
indicates LNK/ACT LED Off
Warning:
The LFP (Link Fault Pass Through) function works only
when both two converters have this capability in pairs.
Furthermore, both LFP converters should be supplied
only by the same manufacturer/vender. The connection
comes from LFP converters with odd models or n on-LFP
converters will cease the LFP function.
6. LED Description
LED Color Function
FX
LNK/ACT
Green
Lit when FX is linking
Blinks when FX’s Data is being transmitted
FX
FDX/COL
Amber
Lit when full-duplex mode is active
Off when half-duplex is active
Blinks when collision occurred
TP
LNK/ACT
Green
Lit when TP is linking
Blinks when FX’s Data is being transmitted
TP 100 Green
Lit when TP’s Data is being transmitted at
100 Mbps
Off when TP’s Data is being transmitted
at 10 Mbps
PWR Green Lit when +5V power is supplied
7. DC Jack and AC-DC Power Adapter
The DC jack's central post is 2.5mm wide and conforms to
• Flow Control: IEEE802.3x compliant for full-duplex
Back pressure flow control for half-duplex
• Power Requirement: 1A@+5VDC from AC-DC Adapter
0.5A@+5VDC from USB port
• Ambient Temperature: 0° to 50°C
• Humidity: 5% to 90%
• Dimensions : 26.2(H) × 70.3(W) × 94(D) mm
Complies with FCC Part 15 Class A and CE Mark
Ä Note: For connecting this device to Router, Bridge or Switch,
please refer to the corresponding device's Technical Manual.
P/N: 1802000510112
Click here for online support:
www.moxa.com/support
The Americas:
+1-714-528-6777 (toll-free: 1-888-669-2872)
Europe:
+49-89-3 70 03 99-0
Asia-Pacific:
+886-2-8919-1230
China:
+86-21-5258-9955 (toll-free: 800-820-5036)
© 2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.
5VDC
USB
DIP Switch
USB
5VDC
DIP Switch
TP-AUTO 100 FDX LFP FDX-FX
TP-FORCE 10 HDX LFP
HDX-FX
DIS
S1
1 2 3 4 5
B
10/100
Switch
●
LFP
10/100
Switch
TP
●
●
TPP
Fiber
Cable
● ●
Remote
Station
● ●
C
● ○
○ ○
○
●
B
10/100
Switch
10/100
Switch
Fiber
Cable
TP
TPP
LFP
Remote
Station
C
Fiber
Cable
B
A
○
○ ○
○
●
○ ○
TP
TP
10/100
Switch
Remote
Station
10/100
Switch
LFP
LFP
C
—4— —5— —6—
Loading...