Moxa Technologies ioLogik 1300, ioLogik 1342, ioLogik 1300-GPRS, ioLogik 1312, ioLogik 1300-HSPA Hardware Installation Manual

– 1 – – 2 – – 3 – - 4 -

P/N: 1802013000020

*1802013000020*

ioLogik 1300 Series

Hardware Installation Guide

First Edition, March 2015

Overview

The ioLogik 1300 series remote I/O products are designed for adding
wireless functionality to existing applications. The ioLogik 1300
series includes a selection of GPRS, HSPA, and 802 .11 a/b/g models
to provide users with a comprehensive se lection of wire less
connectivit y option s. The ioLogik 1300 can be daisy chained with up
to 8 other I/O models (e.g., the ioLogik E1200) to create a large and
distributed I/O array. When the ioLogik 1300 is connected in this
way, different ioLogik E1200 m odules can be used to provide a
combination of different I/O types (DI, DO, AI, AO, RTD, TC). In
addition, t he ioLogik 1300 saves valuable IP resources by providing
the entire array of I/O devices with wireless connect ivity using a
single IP.

For system connectivity, un like traditional I/O servers, which are
passive and must be polled by the SCADA system, when used with
Moxa’s MX-AOPC UA Server the ioLogik 1300 series uses active
messaging to “push” state changes or configured events to the
SCADA system, when occur.

Model Information

• I/O combinations

DI

DIO

AI

ioLogik 1312 8 8 – ioLogik 1342 – 12

4

For more I/O combinations, the ioLogik 1300 can be
daisy chained with up to 8 other I/O modules.

• Communication interface

Communication Interface

ioLogik 1300-GPRS

Serial / Ethernet / GP RS (2G)

ioLogik 1300-HSPA

Serial / Ethernet / GPRS (2G) / HSPA (3G)

ioLogik 1300-WL1

Serial / Eth ernet / Wireless LA N

Package Checklist

• ioLogik 1300 series device

• 3-pin screw te rminal block (for power input)

• 2 12-pin screw t erminal blocks (for I/O)

• 2 8-pin RJ45-to-DB9 cables (CBL-RJ45M9-150)

• 1 antenna (only for wire less modules)

• Documentation and software CD

• Hardware installati on guide (pr inted)

Appearance

Top View

Front View

Physical Dimensions (unit = mm/inch)

Specifications

LAN

Ethernet • 4 switched 10/100 Mbps RJ45 ports

• 1 optimized port for faster downstream

communicat ions with dais y-chained ioL ogik

E1200 units

Note: The optimized daisy-chain port is not supported on wind
industry devices (ioLogik E1261W-T, E1261H-T, or E1263H-T)

Protection

1.5 kV magnet ic isolation

Protocols Modbus/TCP, TCP/IP, UDP, DHCP, B OOTP,

SNMP, HTTP, CGI, SNTP, SMTP

WLAN (ioLogik 13xx-WL1)

Standards

• IEEE 802.11a/b/g for wireless LAN

• IEEE 802.11i for wire less security

Spread Spectrum and
Modulation (typical)

• DSSS with DBPSK, DQPSK, CCK

• OFDM with BPSK, QPSK, 16QAM, 64QAM

• 802.11b:
CCK @ 11/5.5 Mbps, DQ PSK @ 2 Mbps,
DBPSK @ 11 Mbps

• 802.11a/g:
64QAM @ 54/48 Mbps,
16QAM @ 36/24 Mbps,

QPSK @ 18/12 Mbps, BPS K @ 9/6 Mbps

Operating Channels
(central frequency)

• US:

2.412 to 2.462 GHz (11 channels)

5.18 to 5.24 GHz (4 channels)

• EU:

2.412 to 2.472 GHz (13 channels)

5.18 to 5.24 GHz (4 channels)

Security

• Firewall for MAC/IP /Protocol/Port-based

filtering

• 64-bit and 128-bit WEP encrypt ion

• Full WPA/WPA2 Person al or Enterprise
Security (IEEE802.1X /RADIUS, TKIP and

AES)

Transmission Rates • 802.11b: 1, 2, 5.5, 11 Mbps

• 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

Mbps

TX Transmit Power • 802.11b:

Typ. 18±1.5 dBm @ 1 to 11 Mbps

• 802.11g:
Typ. 18±1.5 dBm @ 6 to 24 Mbps,
Typ. 17±1.5 dBm @ 36 Mbps,
Typ. 16±1.5 dBm @ 48 Mbps,
Typ. 16±1.5 dBm @ 54 Mbps

• 802.11a:
Typ. 18±1.5 dBm @ 6 to 24 Mbps,
Typ. 16±1.5 dBm @ 36 Mbps,
Typ. 15±1.5 dBm @ 48 Mbps,

Typ. 14±1.5 dBm @ 54 Mbps

RX Sensiti vity

• 802.11b:

-97 dBm @ 1 Mbps, -94 dBm @ 2 Mbps,

-92 dBm @ 5.5 Mbps, -

90 dBm @ 11 Mbps

• 802.11g:

-88 dBm @ 6 to 24 Mbps,

-85 dBm @ 36 Mbps, -

75 dBm @ 48 Mbps,

-70 dBm @ 54 Mbps

• 802.11a:

-88 dBm @ 6 to 24 Mbps,

-85 dBm @ 36 Mbps, -

75 dBm @ 48 Mbps,

-70 dBm @ 54 Mbps

Cellular (ioLogik 13xx-GPRS/HSPA)

Band Options

• Five-Band:

UMTS/HSPA+(WCDMA/FDD)800/850/
AWS1700/1900/2100 MHz

• Quad-band:
GSM/GPRS/EDGE 850/900/1800/1900

MHz

SIM Control Voltage

3.0 V/1.8 V

Power Requirements

Power Input

9 to 48 VDC24, VDC nominal

Physical Characteristics

Wiring

I/O cable max. 14 AWG

Dimensions

61 x 157 x 115 mm (2.4 x 6.18 x 4.53 in)

Weight

under 1.2 kg

– 5 – – 6 – – 7 – - 8 -

www.moxa.com/support

The Americas:

[phone] (toll-free: 1-888-669-2872)

Europe:

[phone]

Asia-Pacific:

[phone]

China:

[phone] (toll-free: 800-820-5036)

 2015 Moxa Inc. All right s reserved.

Environment Limits

Operating Temperature

Standard Models:

Wide Temp. Models:

-10 to 60°C (14 to 140°F)

-30 to 70°C (-22 to 158°F)

Storage Temperature

-40 to 85°C (-40 to 185°F)

Ambient Relative
Humidity

5 to 95% (non-condensing)
Altitude

Up to 2000 m

Note: Please contact Moxa if you require products guaranteed to

function properly at higher altitudes.

Digital Input

Sensor Type

Wet Contact (NPN or PNP) and Dry Contact

I/O Mode

DI or Event Counter

Dry Contact

• On: short to GND

• Off: open

Wet Contact

(DI to COM)

• On: 10 to 30 VDC

• Off: 0 to 3 VDC

Isolation

3k VDC or 2k Vrms

Counter/Frequency

2.5 kHz

Digital Output (Sink)

I/O Mode

DO or Pulse Output

Pulse Output Frequency

5 kHz

Over-voltage Protection

45 VDC

Over-temperature
Shutdown

175°C (min.)
Over-current Protection

1.5 A per channel @ 25°C

Current Rating

500 mA per channel @ 25°C

Isolation

3k VDC or 2k Vrms

Analog Input (ioLogik 1342)

Type

Differential input

Resolution

16 bits

I/O Mode

Voltage / Current (software selectable)

Input Range ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA

(with burn- out detection)

Accuracy

±0.1% FSR @ 25°C

±0.3% FSR @ -10 and 60°C

±0.5% FSR @ -40 and 75°C

Sampling Rate

• All channels: 400 samples/sec

• Per channel: 100 samples/s ec

Input Impedance

> 1M ohms (m in.)

Built-in Re sistor for

Current Input

120 ohms

Warranty

Warranty Period

5 years

Details

See www.moxa.com/warranty

Hardware Installation

Mounting

There are two sliders on the back of the unit for DIN rail and wall
mounting.

• Mounting on a DIN rail

Pull out the bottom slider; latch the unit onto the DIN rail, and
the push the slider back in.

• Mounting on a wall (optional)

Pull out both the top and bottom sliders and align the screws
accordingl y.

Connecting the Power

Connect a 9 to 48 VDC power lin e to the ioLog ik 1300’s terminal
block V+ terminal; connect the ground from the power supply to the
V- terminal.

For most applica tions, it is desirab le to ground the syst em by
connecting the system’s po wer supply common wire to the chassis
or panel ground. The negative (–V) side of the DC power input
terminal as well as all I/O poin t terminals labeled GND should be
connected to chassis ground.

NOTE

For safety reasons, wires connecting the power supply
should be a t least 2 mm in diameter (e.g., 12 gauge wires).

Connecting to a Network

The ioLogik 1300 has four built-in RJ45 Ethernet ports for connecting
standard direct or crossover Ethernet cables.

LED Indicators

Type

Color

Description

Power
(PWR)

Green

System power is ON

Off

System power is OFF

Ready
(RDY)

Green

System ready

Red

System error

Off

System is not ready

Ethernet Port
(L1/L2/L3/L4)

Green

Ethernet connection enabled in 100 Mbps

Amber

Ethernet connection enabled in 10 Mbps

Flashing

Data transmitting

Off

Disconnected

I/O Channel
Status*

Green

Channel ON

Off

Channel OFF or No Counter/Pulse Signal

W.Link**

Green

Cellular connection established

Off

Off

Signal Status**

Off

No signal, o r No SIM card

1 LED

Weak or ins ufficient (SMS only)

2 LEDs

Average (good for cellular conn ections)

3 LEDs

Excellent s ignal

*Use the rotary switch to select which module's I/O channel status is
displayed.

**Wireless Mo dules Only

I/O Wiring

Digital Inputs/Outp uts

Analog Inputs

System Configuration

Configuration via IOxpress Utility

The configuration of the ioLogik 1300 is mainly done with the
IOxpress utility. IOxpress is a search utility that helps users locate
an ioLogik 1300 device on the local network. The utility can be found
in the Document and Software CD



Software  IOxpress

folder. The latest version can be downloaded from Moxa’s website.

• Default IP Address: 192.168.127.253

• Default Subnet Mask: 255.255.255.0

NOTE Be sure to configure the host PC’s IP address to the same

subnet as the ioLogik 1300. For example, 192.168.127.253

Load Factory Default Settings

There are three ways to restore the ioLogik 1300 to factory default
settings.

1. Hold the RESET button for 5 seco nds.

2. In the IOxpress utility, right-click on the ioLogik device to be
reset and select Reset to Default.

3. Select Load Factory Default from the web console.

WARNING

This equipment is intended to be used in Restricted Access
Locations. External metal parts are hot! Before touching it,
special attention or prote ction is necessary.