Moxa Technologies IKS-6726-8PoE Hardware Installation Manual

— 1 — — 2 — — 3 —

IKS-6726-8PoE Series

Hardware Installation Guide

First Edition, May 2010

Package Checklist

The Moxa IKS-6726-8PoE series industrial rackmount switches are
shipped with the following items. If any of these items are missing or
damaged, please contact your customer service representative for
assistance.

y 1 Moxa IKS-6726-8PoE Switch
y Hardware Installation Guide
y CD-ROM with User’s Manual and SNMP MIB file
y Moxa Product Warranty Statement
y RJ45 to DB9 console port cable
y Protective caps for unused ports
y 2 rack-mount ears

Panel Layouts

1

2

3

4

569

10

11

7

8 12

1. System status LEDs

2. Mode LEDs for the nterface module

3. Port LEDs for the interface module

4. Push-button switch for selecting the mode of the interface module

5. Model name

6. 10/100BaseT(X) port

7. 10/100BaseT(X) PoE port

8. Fast Ethernet / PoE interface module

9. Gigabit Ethernet interface module

10. Serial console port

11. 10-pin terminal block for power inputs and relay output

12. Rack mounting brackets

Dimensions (unit = mm)

440

44

323.5

347.8

462.6

Top View

Rear View

Side ViewSide View

Front View

Fast Ethernet / PoE Interface Modules (for slot 1)

96.8

40.7

40.7

96.8

96.8

40.7

40.7

96.8

PM-7200-8TX

PM-7200-4MSC2TX/PM-7200-4SSC2TX

PM-7200-4MST2TX PM-7200-6MST

PM-7200-6MSC/PM-7200-6SSC PM-7200-2MSC4TX/PM-7200-2SSC4TX

PM-7200-2MST4TX

PM-7200-1LSC6TX

96.8

40.7

96.8

40.7

40.7

96.8

96.8

40.7

96.8

40.7

PM-7200-8PoE

Gigabit Ethernet Interface Modules (for slot 2)

40.7

86.6

PM-7200-2GTXSFP

Rack Mounting

Use four screws to attach the switch to a standard rack.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing
and/or wiring your Moxa industrial rackmount switch.

Calculate the maximum possible current in each power
wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire
size.

If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.

Grounding the Moxa Industrial Rackmount Switch

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

Wiring the Power Inputs

The IKS series switches support dual redundant power supplies: Power
Supply 1 (PWR1) and Power Supply 2 (PWR2). The connections for

PWR1, PWR2, and the RELAY are located on the terminal block. The
front view of the terminal block connectors is shown below.

Wiring the Relay Contact

Each IKS switch has one relay output. Refer to the next section for
detailed instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the terminal
block receptor.

P/N: 1802067260020

— 4 — — 5 — — 6 —

FAULT: The relay contact of the 10-pin terminal block connector are
used to detect user-configured events. The two wires attached to the
RELAY contacts form an open circuit when a user-configured event is
triggered. If a user-configured event does not occur, the RELAY circuit
will be closed.

Wiring the Redundant Power Inputs

Each IKS switch has two
sets of power inputs:
power input 1 and power input 2.

STEP 1: Insert the dual set positive/negative DC wires into PWR1 and
PWR2 terminals (+ → pins 1, 9; - → pins 2, 10), or insert the L/N AC
wires into PWR1 and PWR2 terminals (L → pin 1, 9; N → pin 2,10)

STEP 2: To keep the DC or AC wires from pulling loose, use a
screwdriver to tighten the wire-clamp screws on the front of the terminal
block connector.

LED Indicators

The front panel of the IKS switch contains several LED indicators. The
function of each LED is described in the table below.

LED Color State Description

System LEDs

On

System has passed self-diagnosis test on
boot-up and is ready to run.

GREEN

Blinking

System is undergoing the self-diagnosis
test.

STAT

RED On System failed self-diagnosis on boot-up.

On

Power is being supplied to the main
module’s power input PWR1.

PWR1 AMBER

Off

Power is not being supplied to the main
module’s power input PWR1.

On

Power is being supplied to the main
module’s power input PWR2.

PWR2 AMBER

Off

Power is not being supplied to the main
module’s power input PWR2.

On

The corresponding PORT alarm is enabled
and a user-configured event has been
triggered.

FAULT RED

Off

The corresponding PORT alarm is enabled
and a user-configured event has not been
triggered, or the corresponding PORT
alarm is disabled.

On

This IKS switch is the Master of this Turbo
Ring or the Head of this Turbo Chain.

Blinking

This IKS switch has become Ring Master
of this Turbo Ring after the Turbo Ring
was broken, or Chain Head of this Turbo
Chain after the Turbo Chain was broken..

MSTR/

HEAD

GREEN

Off

This IKS switch is neither the Master of
this Turbo Ring nor the Head of this Turbo
Chain.

On

When this IKS switch enables the coupling
or tailing function to form a back-up path.

CPLR/

TAIL

GREEN

Off

When this IKS switch disables the
coupling and tailing function.

Mode LEDs

On

The corresponding module port’s link is
active.

Blinking

The corresponding module port’s data is
being transmitted.

LNK/ACT GREEN

Off

The corresponding module port’s link is
inactive.

Off

The corresponding module port’s data is
being transmitted at 10 Mbps.

On

The corresponding module port’s data is
being transmitted at 100 Mbps.

SPEED GREEN

Blinking

The corresponding module port’s data is
being transmitted at
1000 Mbps.

On

The corresponding module port’s data is
being transmitted in full duplex mode.

FDX/HDX GREEN

Off

The corresponding module port’s data is
being transmitted in half duplex mode.

On

The corresponding module’s port is the
ring port of this IKS switch.

RING
PORT

GREEN

Off

The corresponding module’s port is not the
ring port of this IKS switch.

On

The corresponding module’s port is the
coupler port of this IKS switch.

COUPLER

PORT

GREEN

Off

The corresponding module’s port is not the
coupler port of this IKS switch.

PoE Module LEDs

On The corresponding port is supplying po wer

PoE AMBER

Off

The corresponding port is not supplying
power

Specifications

Technology

Standards IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x,

802.1D, 802.1W, 802.1Q, 802.1p, 802.1X,

802.3ad

Flow control IEEE 802.3x flow control, back pressure flow

control

Interface

Fast Ethernet Slot 1 for any combination of 4, 6, 7, or 8-port

PM-7200 fast Ethernet modules with
10/100BaseT(X) (TP/PoE/M12
interface), 100BaseFX (SC/ST connector), or
100BaseSFP

Gigabit Ethernet Slot 2 for 2-port PM-7200 Gigabit Ethernet combo

module with 10/100/1000BaseT(X), 1000Base

SFP slots (SFP slot, LC connector)
System LED
Indicators

STAT, PWR1, PWR2, FAULT, MSTR/HEAD,

CPLR/TAIL

Mode LED
Indicators

LNK/ACT, FDX/HDX, SPEED, RING PORT,

COUPLER PORT
PoE LED
Indicators

PoE

Alarm Contact One relay output with current carrying capacity of

3A @ 30 VDC or 3A @ 240 VAC
Optical Fiber (100BaseFX)
Distance Multi-mode

0 to 5 km, 1300 nm (50/125μm, 800 MHz*km)

0 to 4 km, 1300 nm (62.5/125μm, 500 MHz*km)

Single-mode

0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
Min. TX Output Multi-mode: -20 dBm; single-mode: -5 dbm
Max. TX Output Multi-mode: -10 dBm; single-mode: 0 dbm
RX Sensitivity Multi-mode: -32 dBm; single-mode: -34 dbm

Power

Input Voltage 48VDC (44 to 57V)
Input Current Max. 3.3A @ 48VDC

Physical Characteristics

Housing IP 30 protection, metal case
Dimensions
(W x H x D)

440 x 44 x 325 mm (17.32 x 1.73 x 12.80 in.)

Weight IKS-6726-8PoE-F-48-T 4260 g

IKS-6726-8PoE-F-48-48-T 4460 g
Installation 19” rack mounting

Regulatory Approvals

Safety EN60950-1
Road Traffic NEMA TS2
Rail Traffic EN50121-4
EMI FCC Part 15, CISPR (EN55022) class A
Environmental Limits
Operating Temp. -40 to 75°C (-40 to 167°F)
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity.

5 to 95% (non-condensing)

Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty

Note: A shielded cable is required for EN50121-4.

Click here for online support:

www.moxa.com/support

The Americas: [phone] (toll-free: 1-888-669-2872)

Europe: [phone]

Asia-Pacific: [phone]

China: [phone] (toll-free: 800-820-5036)

© 2010 Moxa Inc., all rights reserved.

Reproduction without permission is prohibited.