Moxa Technologies EtherDevice EDS-G500E, EtherDevice EDS-G508E, EtherDevice EDS-G512E-4GSFP, EtherDevice EDS-G516E-4GSFP Installation Manual

 2013 Moxa Inc. All rights reserved.

P/N: 1802005000020

EDS-G500E Series

Hardware Installation Guide

Moxa EtherDevice™ Switch

First Edition, July 2013

- 2 -

Package Checklist

The EDS-G500E is shipped with the following items. If any of these items
are missing or damaged, please contact your customer service
representative for assistance.

• 1 EDS-G508E or EDS-G512E-4GSFP or EDS-G516E-4GSFP Ethernet
switch

• Hardware installation guide

• Documentation and software CD

• Moxa product warranty statement

• USB cable

• Protective caps for unused ports

Features

• Up to 12 10/100/1000BaseT(X) ports and 4 100/1000BaseSFP ports

• Turbo Ring and Turbo Chain (recovery time < 50 ms @ 250 switches),

RSTP/STP, and MSTP for network redundancy

• RADIUS, TACACS+, SNMPv3, IEEE 802.1x, HTTPS, and SSH to
enhance network security

• EtherNet/IP, PROFINET, and Modbus/TCP protocols supported for
device management and monitoring

- 3 -

Panel Views of EDS-G500E Series

Front Panel

EDS-G508E

EDS-G512E-4GSFP

Front Panel

1.

1000BaseT(X) LED indicator

2.

10/100BaseT(X) LED indicator

3.

10/100/1000BaseT(X) ports

EDS-G508E: 1 to 8
EDS-G512E-4GSFP: 1 to 8
EDS-G516E-4GSFP: 1 to 12

4.

System status LED:

• STATE LED indicator

• PWR1 LED indicator

• PWR2 LED indicator

• FAULT LED indicator

• MSTR/HEAD LED indicator

• CPLR/TAIL LED indicator

5.

USB storage port

6.

SFP port LED indicator

EDS-G512E-4GSFP: 9 to 12
EDS-G516E-4GSFP: 13 to 16

7.

100/1000BaseSFP slots

8.

Model Name

EDS-G516E-4GSFP

- 4 -

Top Panel

Rear Panel

Top Panel

1.

Reset button

2.

USB console port

3.

DIP switches for Turbo Ring,

Ring Master, and Ring Coupler

4.

Grounding screw

5.

4-pin terminal block for digital

input and power input 2

6.

4-pin terminal block for relay

output and power input 1

Rear Panel

1.

Screw holes for wall mounting

kit

2.

DIN-rail mounting kit

- 5 -

Mounting Dimensions

Unit = mm (inch)

- 6 -

DIN-Rail Mounting

The metal DIN-rail kit is fixed to the back panel of the EDS-G500E series
when you take it out of the box. Mount the EDS-G500E series on
corrosion-free mounting rails that meet the EN 60715 standard.

Installation

STEP 1—Insert the upper lip of the DIN rail into the DIN-rail mounting kit.

STEP 2—Press the EDS-G500E series towards the DIN rail until it snaps
into place.

Removal

STEP 1—Pull down the latch on the mounting kit with a screwdriver.

STEP 2 & 3—Slightly pull the EDS-G500E series forward and lift up to

remove it from the DIN rail.

- 7 -

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa EDS­G500E series on the wall, as shown in the following illustrations:

STEP 1—Remove the
aluminum DIN rail attachment
plate from the rear panel

of

the EDS

-G500E series, and

then attach the wall mount
plates

with M3 screws, as

shown

in the figure at the

right.

STEP 2—

Mounting the EDS-G500E series on the

wall requires 4 screws. Use the

EDS-G500E series

,
with wall mount plates attached, as a guide to
mark the correct locations of the 4 screws. The
heads of the screws should be less than 6.0 mm in
diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure on at right.

NOTE

Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.

STEP 3—Once the screws are
fixed

to the wall, insert the

four screw heads through the
wide parts of the
keyhole

-shaped apertures,

and then slide

the EDS-

G500E

downwards, as indicated

in

the figure

at

the right. Tighten

the four screws for

more

stability.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been
switched off or the area is known to be non

-hazardous. The

devices may only be connected to the supply voltage shown on
the type plate. The devices are designed

for operation with a

S

afety Extra-Low V

oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
S

afety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

- 8 -

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum

current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately

• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together

• You should separate input wiring from output wiring

• We advise that you label the wiring to all devices in the system.

Grounding the Moxa EDS-G500E Series

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-G500E series has one set of relay output. This relay contact uses
two contacts of the terminal block on the EDS-G500E’s top panel. Refer to
the next section for detailed instructions on how to connect the wires to
the terminal block connector, and how to attach the terminal block
connector to the terminal block receptor. In this section, we illustrate the
meaning of the two contacts used to connect the relay contact.

- 9 -

FAULT:

The two contacts of the 6-pin terminal
block connector are used to detect
user-configured events. The two wires
attached to the fault contacts form an
open circuit when a user

-configured

event is triggered. If a user-configured
event does not occur, the

fault circuit

remains closed.

Wiring the Redundant Power Inputs

The EDS-G500E series has two sets of power inputs—power input 1 and
power input 2. The top and front views of one of the terminal block
connectors are shown here.

STEP 1: Insert the negative/positive
DC wires into the V

-/V+ terminals,

respectively.

STEP 2:

To keep the DC wires from

pulling loose, use a small flat

-blade

screwdriver to tighten the wire-clamp
screws on the front of the terminal
block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the
terminal block receptor, which is
located on the EDS-G500E’s top panel.

Wiring the Digital Inputs

The EDS-G500E series has one set of digital input (DI). The DI consists of
two contacts of the 4-pin terminal block connector on the EDS-G500E's
top panel, which are used for the two DC inputs. The top and front views
of one of the terminal block connectors are shown here.

STEP 1: Insert the negative
(ground)/positive DI wires into the

┴

/I terminals, respectively.

STEP 2:

To keep the DI wires from

pulling loose, use a small flat

-blade

screwdriver to tighten the wire-clamp
screws on the front of the terminal
block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the
terminal block receptor,

which is

located on the EDS-G500E’s top panel.

Communication Connections

Each EDS-G500E series switch has 4 types of communication ports:

• 1 USB console port (type B connector)

• 1 USB storage port (type A connector)

• 8 (EDS-G508E/EDS-G512E-4GSFP) or 12 (EDS-G516E-4GSFP)

10/100/1000BaseT(X) Ethernet ports

• 4 100/1000Base SFP slots (EDS-G512E-4GSFP/EDS-G516E-4GSFP)

- 10 -

USB Console Connection

The EDS-G500E series has one USB console port (type B connector),
located on the top panel. Use the USB cable (provided in the product
package) to connect the EDS-G500E's console port to your PC's USB port
and install the USB driver (available in the software CD) on the PC. You
may then use a console terminal program, such as Moxa PComm Terminal
Emulator, to access the EDS-G500E’s console configuration utility.

USB Console Port (Type B Connector) Pinouts

Pin

Description

1

D– (Data -)

2

VCC (+5V)

3

D+ (Data+)

4

GND (Ground)

USB Storage Connection

The EDS-G500E series has one USB storage port (type A connector) on
the front panel. Use Moxa ABC-02-USB-T automatic backup configurator
to connect the EDS-G500E's USB storage port for configuration backup,
firmware upgrade or system log file backup.

ABC-02-USB Installation

Plug the ABC-02-USB into the USB storage port of the Moxa EDS-G500E
series. Securing the ABC-02-USB on the wall with an M4 screw is
suggested.

USB Storage Port (Type A Connector) Pinouts

Pin

Description

1

VCC (+5V)

2

D– (Data -)

3

D+ (Data+)

4

GND (Ground)

- 11 -

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over
copper wires.

MDI/MDI-X Port Pinouts

Pin

Signal

1

TRD(0)+

2

TRD(0)-

3

TRD(1)+

4

TRD(2)+

5

TRD(2)-

6

TRD(1)-

7

TRD(3)+

8

TRD(3)-

100/1000BaseSFP (mini-GBIC) Fiber Port

The Gigabit Ethernet ports on the EDS-G500E series are
100/1000BaseSFP Fiber ports, which require using the 100M or 1G
mini-GBIC fiber transceivers to work properly. Moxa provides completed
transceiver models for different distance requirement.

The concept behind the LC port and cable is quite straightforward.
Suppose that you are connecting devices I and II; contrary to electrical
signals, optical signals do not require a circuit in order to transmit data.
Consequently, one of the optical lines is used to transmit data from device
I to device II, and the other optical line is used transmit data from device
II to device I, for full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)
port of device II, and the Rx (receive) port of device I to the Tx (transmit)
port of device II. If you make your own cable, we suggest labeling the two
sides of the same line with the same letter (A-to-A and B-to-B, as shown
below, or A1-to-A2 and B1-to-B2).

LC-Port Pinouts

LC-Port to LC-Port Cable Wiring

ATTENTION

This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.

Reset Button

There are two functions available on the Reset Button. One is to reset the
Ethernet switch to factory default settings by pressing and holding the
Reset button for 5 seconds. Use a pointed object, such as a straightened

- 12 -

paper clip or toothpick, to depress the Reset button. This will cause the
STATE LED to blink once a second. After depressing the button for 5
continuous seconds, the STATE LED will start to blink rapidly. This
indicates that factory default settings have been loaded and you can
release the reset button.
When the ABC-02-USB is connected to the EDS-G500E Ethernet switch,
the reset button allows quick configuration and backs up log files to the
ABC-02-USB. Press the Reset button on top of the EDS-G500E, the
Ethernet switch will start backing up current system configuration files
and event logs to the ABC-02-USB.

NOTE

Do NOT power off the Ethernet switch when loading default
settings.

Turbo Ring DIP Switch Settings

EDS-G500E series are plug-and-play managed redundant Ethernet
switches. The proprietary Turbo Ring protocol was developed by Moxa to
provide better network reliability and faster recovery time. Moxa Turbo
Ring’s recovery time is less than 300 ms (Turbo Ring) or 50 ms (Turbo
Ring V2) —compared to a 3- to 5-minute recovery time for commercial
switches—decreasing the possible loss caused by network failures in an
industrial setting.

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of
EDS-G500E series that can help setup the Turbo Ring easily within
seconds. If you do not want to use a hardware DIP switch to setup the
Turbo Ring, you can use a web browser, telnet, or console to disable this
function.

NOTE

Please refer to the Turbo Ring section in Communication
Redundancy

User's Manual for more detail information about

the setting and usage of Turbo Ring and Turbo Ring V2.

EDS-G500E Series DIP Switches

The default setting for each DIP Switch is OFF. The
following table explains the effect of setting the DIP
Switch to the ON position

.

“Turbo Ring” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

Reserved for
future use.

ON: Enable

s this

EDS as

the Ring

Master.

ON: Enables the
default “Ring
Coupling” ports.

ON: Activates
DIP switch 2 and
3 to configure
“Turbo Ring”

settings.

OFF: This EDS

will not be the
Ring Master.

OFF: Do not use

this EDS as the
ring coupler.

OFF: DIP switch

1, 2, and

3 will be

disabled.

- 13 -

“Turbo Ring V2” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

ON: Enables the
default “Ring
Coupling
(backup)” port
when DIP switch
3 is already

enabled.

ON: Enables this
EDS as the Ring
Master.

ON: Enables the
default “Ring
Coupling” port.

ON: Activates
DIP switch 1, 2,
and 3 to
configure “Turbo
Ring V2”
settings.

OFF: Enables the

default “Ring
Coupling
(primary)” port
when DIP switch
3 is already

enabled.

OFF: This EDS

will not be the
Ring Master.

OFF: Do not use
this EDS as a ring

coupler.

OFF: DIP switch

1, 2, and

3 will be

disabled.

NOTE

You must enable the Turbo Ring function first

before using the

DIP switch to activate the Master and Coupler functions.

NOTE

If you do not enable any of the EDS

-G500E series

switches to be
the Ring Master, the Turbo Ring protocol will automatically
choose the EDS

-G500E series with the smallest MAC address

range to be the Ring Master. If you accidentally enable more than
one EDS

-G500E series to be the Ring Master, these EDS-G500

E

series

switches will auto-

negotiate to determine which one will be

the Ring Master.

LED Indicators

The front panel of the Moxa EDS-G500E series contains several LED
indicators. The function of each LED is described in the following table:

LED

Color

Status

Description

STATE

Green

On

The system passed the self-diagnosis test
on boot-up and is ready to run.

Blinking

1. The switch is under reset progress (1
time/s).

2. Detect ABC-02-USB connect to the

switch (1 time/2s).

Red On

The system failed self-diagnosis on

boot-up.

• RAM Test Fail / System Info. Read Fail
/ Switch Initial Fail / PTP PHY Error.
(+ Green MSTR lit on : HW FAIL)

• FW Checksum Fail / Uncompress Fail.

(+ Green Coupler lit on: SW FAIL)

FAULT Red On

1. The signal contact is open.

2. ABC Loading/Saving Fail.

3.

The port being disabled because of the

ingress multicast and broadcast
packets exceed the ingress rate limit.

4. Incorrect loop connection in a single

switch.

- 14 -

LED

Color

Status

Description

5. Invalid Ring port connection.

PWR1 Amber

On

Power is being supplied to the main

module’s power input PWR1.

Off

Power is not being supplied to the main
module’s power input PWR1.

PWR2 Amber

On

Power is being supplied to the main
module’s power input PWR2.

Off

Power is not being supplied to the main

module’s power input PWR2.

MSTR/

HEAD

Green

On

1. The switch is set as the Master of the

Turbo Ring, or as the Head of the
Turbo Chain.

2. POST H.W. Fail (+Stat on and Fault

blinking).

Blinking

1. The switch has become the Ring

Master of the Turbo Ring.

2.

The Head of the Turbo Chain, after the

Turbo Ring or the Turbo Chain is
down.

3. The switch is set as Turbo Chain’s
Member and the corresponding chain

port is down.

Off

1. The switch is not the Master of this

Turbo Ring.

2. This switch is set as a Member of the

Turbo Chain.

CPLR/

TAIL

Green

On

1. The switch’s coupling function is

enabled to form a back-up path.

2. When it’s set as the Tail of the Turbo
Chain.

3. POST S.W. Fail (+Stat on and Fault

blinking)

Blinking

1. Turbo Chain is down.

2. The switch is set as Turbo Chain’s
Member and the corresponding chain

port is down.

Off

1. This switch has disabled the coupling

function.

2. This switch is set as a Member of the

Turbo Chain.

FAULT +

MSTR/HEAD

+ CPLR/TAIL

Rotate

Blinking

Sequentially

ABC-02-USB is importing/exporting files.

STATE +

FAULT +

MSTR/HEAD

+ CPLR/TAIL

Blinking

Switch is being discovered/located by
MXview (2 times/s).

10M/
100M

(TP)

Amber

On

TP port’s 10 or 100 Mbps link is active.

Blinking

Data is being transmitted at 10 or 100
Mbps.

Off

TP port’s 10/100 Mbps link is inactive.

1000M

(TP)

Green

On

TP port’s 1000 Mbps link is active.

Blinking

Data is being transmitted at 1000 Mbps.

Off

TP port’s 1000 Mbps link is inactive.

- 15 -

LED

Color

Status

Description

100M

(SFP)

Amber

On

SFP port’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100 Mbps.

Off

SFP port’s 100 Mbps link is inactive.

1000M

(SFP)

Green

On

SFP port’s 1000 Mbps link is active.

Blinking

Data is being transmitted at 1000 Mbps.

Off

SFP port’s 1000 Mbps link is inactive.

Specifications

Technology

Standards

IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseT(X) and 100BaseFX
IEEE 802.3ab for 1000BaseT(X)

IEEE 802.3z for 1000BaseX

Protocols IGMPv1/v2/v3, GMRP, GVRP, SNMPv1/v2c/v3,

DHCP Server/Client, DHCP Option 66/67/82, BootP,

TFTP, SNTP, SMTP, RARP, RMON, HTTP, HTTPS,
Telnet, SSH, Syslog, EtherNet/IP, PROFINET,
Modbus/TCP, SNMP Inform, LLDP, IEEE 1588 PTP

V2, IPv6, NTP Server/Client

MIB

MIB-II, Ethernet-Like MIB, P-BRIDGE MIB,

Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON MIB

Group 1, 2, 3, 9

Flow Control

IEEE 802.3x flow control, back pressure flow control

Interface

RJ45 Ports

8 (EDS-G508E/EDS-G512E-4GSFP) or 12
(EDS-G516E-4GSFP) 10/100/1000BaseT(X)

Fiber Ports

4-port 100/1000BaseSFP slot
(EDS-G512E-4GSFP/EDS-G516-4GSFP only)

USB Ports USB console port (type B connector)

USB storage port (type A connector)

Button

Reset button

LED Indicators

PWR1, PWR2, FAULT, STATE, 10/100M, 100/1000M,
MSTR/HEAD, CPLR/TAIL

Alarm Contact

1 relay output with current carrying capacity of 1 A
@ 24 VDC

Digital Input

1 input with the same ground, but electrically

isolated from the electronics.
+13 to +30V for state “1”

-30 to +3V for state “0”

Max. input current: 8 mA

Power

Input Voltage

12/24/48/-48 VDC, redundant dual inputs

Input Current EDS-G516E: 0.46 A @ 24 VDC

EDS-G512E: 0.4 A @ 24 VDC

EDS-G508E: 0.33 A @ 24 VDC

Connection

2 removable 4-contact terminal blocks

Overload Current
Protection

Present

Reverse Polarity

Protection

Present

Physical Characteristics

Housing

Metal, IP30 protection

- 16 -

Dimension

79.2 x 135 x 137 mm (3.1 x 5.3 x 5.4 in)

Installation

DIN-rail mounting, wall mounting (with optional kit)

Environmental Limits

Operating

Temperature

-10 to 60°C (14 to 140°F) for standard models

-40 to 75°C (-40 to 167°F) for -T models

Storage
Temperature

-40 to 85°C (-40 to 185°F)

Ambient Relative
Humidity

5 to 95% (non-condensing)

Altitude Up to 2000m

Note: Please contact Moxa if you require products

guaranteed to function properly at higher altitude.

Regulatory Approvals

Safety

UL 508

EMI

FCC Part 15 Subpart B Class A, EN 55022 Class A

EMS

EN 61000-4-2 (ESD) Level 4, EN 61000-4-3 (RS)

Level 3,
EN 61000-4-4 (EFT) Level 4, EN 61000-4-

5 (Surge)

Level 4,

EN 61000-4-6 (CS) Level 3, EN 61000-4-8

Shock

IEC 60068-2-27

Free Fall

IEC 60068-2-32

Vibration

IEC 60068-2-6

Warranty

Warranty

5 years

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:
Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):
Toll

-free: 800-820-5036

Tel:

[phone]

Fax:

[phone]

Moxa Europe

:

Tel:

[phone]

Fax:

[phone]

Moxa Asia

-Pacific:

Tel:

[phone]

Fax:

[phone]