Moxa Technologies EDS-P506A-4PoE, EDS-P506A-4PoE-MM-SC, EDS-P506-4PoE, EDS-P506A-4PoE-SS-SC, EDS-P506A-4PoE-MM-ST Hardware Installation Manual

Moxa EtherDevice™ Switch

EDS-P506A-4PoE Series

Hardware Installation Guide

First Edition, July 2010

© 2010 Moxa Inc. All rights reserved.

Reproduction without permission is prohibited.

P/N: 1802005060010

— 1 —

Overview

The Moxa EtherDevice™ EDS-P506A-4PoE Series Ethernet switches are

managed redundant Ethernet switches that come standard with 4
10/100BaseT(X) 802.3at/af (PoE/PoE+) compliant Ethernet ports, and 1 or 2
10/100BaseT(X) Ethernet ports or 1 or 2 100BaseFX (SC/ST-type connector)
fiber ports. The EDS-P506A-4PoE Ethernet switches provide up to 30 watts
of power per PoE port, and allow power to be supplied to connected devices
(such as surveillance cameras, wireless access points, and IP phones) when
power is not readily available or cost-prohibitive to provide locally. The
EDS-P506A-4PoE Ethernet switches are highly versatile, and their fiber ports
can transmit data up to 40 km from the device to the control center with high
EMI immunity. The Ethernet switches support a variety of management
functions, including Turbo Chain, IEEE 1588 PTP, Turbo Ring, RSTP/STP,
IGMP, VLAN, QoS, RMON, bandwidth management, and port mirroring.
The EDS-P506A-4PoE series is designed especially for security automation
applications such as IP surveillance and gate of entry systems, which can
benefit from a scalable backbone construction and Power-over-Ethernet
support.

The EDS-P506A-4PoE can operate from 0 to 60°C or -40 to 75°C for T
models and are designed to withstand a high degree of vibration and shock.
The rugged hardware design makes the EDS-P506A-4PoE Series perfect for
ensuring that your Ethernet equipment can operate in critical industrial
environments, and complies with FCC and CE standards.

NOTE

Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch.

EDS = Moxa EtherDevice Switch

Package Checklist

The EDS-P506A-4PoE is shipped with the following items. If any of these

items are missing or damaged, please contact your customer service

representative for assistance.

y 1 EDS-P506A-4PoE EtherDevice Switch
y Hardware Installation Guide (this guide)
y CD-ROM with user’s manual and Windows utility
y Moxa product warranty statement
y RJ45 to DB9 console port cable
y Protective caps for unused ports
y DIN-Rail mounting kit (attached to the EDS-P506A-4PoE’s rear panel by

default)

— 2 —

EDS-P506A-4PoE Panel Views
(standard type)

EDS-P506-4PoE
Front Panel View

16

MSTR/
HEAD

CPLR/
TAIL

11

6
7
8

9
10

14

15

12
13

19

RS-232 CONSOLE

------

ON

OFF

MASTER
COUPLER

TURBO
RING

PWR1

4

3

2

1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

I1

I2

Top Panel View

1

2

3

4

1

Rear Panel View

2

18

17

5

2

17

1. Grounding screw

2. Terminal block for power input
PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 10/100 BaseT(X) Ports

17. Screw hole for wall mounting
kit

18. DIN-Rail kit

19. PoE LEDs

— 3 —

EDS-P506A-4PoE Panel Views
(SC-type)

EDS-P506A-4PoE-MM-SC

/

EDS-P506A-4PoE-SS-SC
Front Panel View

14

15

16

12
13

11

6
7
8

9
10

17

20

RS-232 CONSOLE

------

ON

OFF

MASTER
COUPLER

TURBO
RING

PWR1

43

2

1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

I1

I2

Top Panel View

1

2

3

4

5

2

1

Rear Panel View

2

19

18

18

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay
output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting

kit

19. DIN-Rail kit

20. PoE LEDs

— 4 —

EDS-P506A-4PoE Panel Views
(ST-type)

EDS-P506A-4PoE-MM-ST
Front Panel View

14

15

16

12
13

11

6
7

8
9

10

17

20

RS-232 CONSOLE

------

ON

OFF

MASTER
COUPLER

TURBO
RING

PWR1

4

3

2

1

PWR2

RELAY2

RELAY1

DI1

DI2

V2-

V2+

I1

I2

Top Panel View

1

2

3

4

1

Rear Panel View

2

19

18

18

5

2

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay
output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. MSTR/HEAD LED indicator

10. CPLR/TAIL LED indicator

11. Turbo Chain logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100 BaseT(X) PoE Ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting

kit

19. DIN-Rail kit

20. PoE LEDs

— 5 —

Mounting Dimensions

30mm(1.18in)

9.75mm(0.38in)

15mm(0.59in)

131.5mm(5.18in)

80.05mm(3.15in)

135mm(5.31in)

70mm(2.76in)

30.5mm(1.2in)

34mm(1.34in)

51.6mm(2.03in)

48.39mm(1.9in)

67mm(2.64in)

14.6mm(0.57in) 20mm(0.79in) 36.6mm(1.44in) 29.5mm(1.16in) 20mm(0.79in) 14.3mm(0.56in)

Side View

DlN-Rail Kit

Front View

Rear View

DlN-Rail Kit

Wall Mounting Kit

Wall Mounting Kit

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of the EDS-P506A-4PoE when you take it out of the box. If you need
to reattach the DIN-Rail attachment plate to the EDS-P506A-4PoE, make
sure the stiff metal spring is situated towards the top, as shown by the
following figures.

STEP 1—Insert the top of the

DIN-Rail into the slot just below the
stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown in
the following illustration.

metal
spring

DIN-Rail

metal
spring

DIN-Rail

To remove the EDS-P506A-4PoE from the DIN-Rail, simply reverse Steps 1

and 2 above.

— 6 —

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the Moxa
EDS-P506A-4PoE on the wall, as shown in the following illustrations:

STEP 1—Remove the

aluminum DIN-Rail
attachment plate from the rear

p

anel of the
EDS-P506A-4PoE, and then
attach the wall mount plates
with M3 screws, as shown in

the figure to the right.



STEP 2—Mounting the EDS-P506A-4PoE on the wall requires 4

screws. Use the EDS-P506A-4PoE, with wall mount plates
attached, as a guide to mark the correct locations of the 6 screws.
The heads of the screws should be less than 6.0 mm in diameter,
and the shafts should be less than 3.5 mm in diameter, as shown
in the figure to the right.

6.0 mm

3.5 mm

NOTE

Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the
way—leave about 2 mm to allow
room for sliding the wall mount

p

anel between the wall and the
screws.

STEP 3—Once the screws are fixed

to the wall, insert the four screw
heads through the wide parts of the
keyhole-shaped apertures, and then
slide the EDS-P506A-4PoE
downwards, as indicated in the
figure at the right. Tighten the four
screws for more stability.

MSTR/
HEAD

CPLR/
TAIL

MSTR/
HEAD

CPLR/
TAIL

— 7 —

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been
switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with
IEC60950-1/EN60950-1.

ATTENTION

This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC60950-1/EN60950-1
(or similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.

Read and follow these guidelines:

y Use separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.

y You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.

y You should separate input wiring from output wiring.
y We advise that you label the wiring to all devices in the system.

— 8 —

Grounding the Moxa EDS-P506A-4PoE

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-P506A-4PoE has two sets of relay outputs—relay 1 and relay 2.
Each relay contact uses two contacts of the terminal block on the
EDS-P506A-4PoE’s top panel. Refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector, and
how to attach the terminal block connector to the terminal block receptor.

In this section, we illustrate the meaning of the two contacts used to connect
the relay contact.

RELAY1

RELAY1

RELAY2

RELAY2

FAULT:

The two sets of relay contacts of the
6-pin terminal block connector are
used to detect user-configured
events. The two wires attached to
the fault contacts form an open
circuit when a user-configured
event is triggered. If a
user-configured event does not

occur, the fault circuit remains

closed.

Wiring the Redundant Power Inputs

The EDS-P506A-4PoE has two sets of power inputs—power input 1 and
power input 2. The top two contacts and the bottom two contacts of the 6-pin
terminal block connector on the EDS-P506A-4PoE’s top panel are used for
the two digital inputs. The top and front views of one of the terminal block
connectors are shown here.

PWR1

PWR2

V1- V1+

PWR1

V2- V2+

PWR2

V1- V1+ V2- V2+

STEP 1: Insert the

negative/positive DC wires into the
V-/V+ terminals, respectively.

STEP 2: To keep the DC wires

from pulling loose, use a small
flat-blade screwdriver to tighten the
wire-clamp screws on the front of
the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the
terminal block receptor, which is
located on the EDS-P506A-4PoE’s
top panel.

— 9 —

Wiring the Digital Inputs

The EDS-P506A-4PoE has two sets of digital inputs, DI 1 and DI 2. Each DI
consists of two contacts of the 6-pin terminal block connector on the
EDS-P506A-4PoE’s top panel, which are used for the two DC inputs. The top
and front views of one of the terminal block connectors are shown here.

I1

D2I

I2

D1I

I1 I2

D2ID1I

STEP 1: Insert the negative

(ground)/positive DI wires into the
┴/I1 terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade
screwdriver to tighten the
wire-clamp screws on the front of
the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the
terminal block receptor, which is
located on the EDS-P506A-4PoE’s

top panel.

Turbo Ring DIP Switch Settings

EDS-P506A-4PoE switches are plug-and-play managed redundant Ethernet
switches. The proprietary Turbo Ring protocol was developed by Moxa to
provide better network reliability and faster recovery time. Moxa Turbo Ring’s

recovery time is less than 300 ms (Turb o Ring) or 20 ms (Turbo Ring
V2) —compared to a 3- to 5-minute recovery time for commercial

switches—decreasing the possible loss caused by network failures in an
industrial setting.

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of
EDS-P506A-4PoE that can help setup the Turbo Ring easily within seconds. If
you do not want to use a hardware DIP switch to setup the Turbo Ring, you can
use a web browser, telnet, or console to disable this function.

NOTE

Refer to the Turbo Ring DIP Switch section and Using
Communication Redundancy section in the User’s Manual for
detailed information about the settings and usage of Turbo Ring
and Turbo Ring V2.

EDS-P506A-4PoE Series DIP Switches

2

1

------

MASTER
COUPLER
TURBO

RING

4

3

The default setting for each DIP Switch is OFF. The
following table explains the effect of setting the DIP
Switch to the ON position.

— 10 —

“Turbo Ring” DIP Switch Settings

DIP 1 DIP 2 DIP 3 DIP 4

Reserved for
future use.

ON

: Enables this
EDS as the Ring
Master.

ON: Enables the
default “Ring
Coupling” ports.

ON: Activates
DIP switches 1,
2, 3 to configure
“Turbo Ring”
settings.

OFF: This EDS
will not be the
Ring Master.

OFF

: Do not use
this EDS as the
ring coupler.

OFF: DIP
switches 1, 2, 3
will be disabled.

“Turbo Ring V2” DIP Switch Settings

DIP 1 DIP 2 DIP 3 DIP 4

ON: Enables the
default “Ring
Coupling
(backup)” port.

ON

: Enables this
EDS as the Ring
Master.

ON: Enables the
default “Ring
Coupling” port.

ON: Activates
DIP switches 1,
2, 3 to configure
“Turbo Ring V2”
settings.

OFF: Enables the
default “Ring
Coupling
(primary)” port.

OFF

: This EDS
will not be the
Ring Master.

OFF

: Do not use
this EDS as a
ring coupler.

OFF: DIP
switches 1, 2, 3
will be disabled.

NOTE

You must enable the Turbo Ring function first before using the DIP
switch to activate the Master and Coupler functions.

NOTE

If you do not enable any of the EDS-P506A-4PoE switches to be
the Ring Master, the Turbo Ring protocol will automatically choose
the EDS-P506A-4PoE with the smallest MAC address range to be
the Ring Master. If you accidentally enable more than one
EDS-P506A-4PoE to be the Ring Master, these EDS-P506A-4PoE
switches will auto-negotiate to determine which one will be the
Ring Master.

— 11 —

LED Indicators

The front panel of the Moxa EDS-P506A-4PoE contains several LED
indicators. The function of each LED is described in the following table:

LED Color State Description

PWR1 AMBER

On

Power is being supplied to power input
P1.

Off

Power is not being supplied to power

input P1.

PWR2 AMBER

On

Power is being supplied to power input
P2.

Off

Power is not being supplied to power

input P2.

FAULT RED

On

When a user-configured event is
triggered.

Off

When a user-configured event is not
triggered.

MSTR/HEAD GREEN

On

When the EDS-P506A-4PoE is set as
the Master of the Turbo Ring, or as the
Head of the Turbo Chain.

Blinking

The EDS-P506A-4PoE has become the
Ring Master of the Turbo Ring, or the
Head of the Turbo Chain, after the
Turbo Ring or the Turbo Chain is down.

Off

When the EDS-P506A-4PoE is not the
Master of this Turbo Ring or is set as
the Member of the Turbo Chain.

CPLR/TAIL GREEN

On

When the EDS-P506A-4PoE coupling
function is enabled to form a back-up
path, or when it’s set as the Tail of the
Turbo Chain.

Blinking

When the Turbo Chain is down.

Off

When the EDS-P506A-4PoE disables
the coupling function.

10M
(TP)

GREEN

On

TP port’s 10 Mbps link is active.

Blinking

Data is being transmitted at 10 Mbps.

Off

TP port’s 10 Mbps link is inactive.

100M

(TP)

GREEN

On

TP port’s 100 Mbps link is active.

Blinking

Data is

b

eing transmitted at 100 Mbps.

Off

TP port’s 100 Mbps link is inactive.

100M

(FX)

GREEN

On

FX por

t

’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100 Mbps.

Off

FX por

t

’s 100 Mbps link is inactive.

PoE+ AMBER

On

Power is being supplied to Powered
Device (PD)

Blinking

PoE port is in Powe

r

-Fail status

Off

Power is not being supplied to Powered

Device (PD)

— 12 —

Specifications of the
EDS-P506A-4PoE Series

Auto MDI/MDI-X Connection

The Auto MDI/MDI-X function allows users to connect the
EDS-P506A-4PoE’s 10/100BaseTX ports to any kind of Ethernet device,
without needing to pay attention to the type of Ethernet cable being used for

the connection. This means that you can use either a straight-through cable or
cross-over cable to connect the EDS-P506A-4PoE to Ethernet devices.

Fiber Ports

The Moxa EDS-P506A-4PoE’s fiber ports operate at a fixed 100 Mbps speed
and full-duplex mode to provide excellent performance. The fiber ports are
factory-built as either multi-mode or single-mode SC/ST connectors. Therefore,
you should use fiber cables that have SC/ST connectors at both ends. When
plugging the connector into the port, make sure the slider guide is positioned to
the right side such that it fits snuggly into the port.

slider

slider guide

slider ridges

slider

slider guide

slider ridges

The 100 Mbps fiber ports are switched ports and perform as a domain to
provide a high bandwidth backbone connection that supports long fiber cable
distances (up to 5 km for multi-mode, and 40 km for single-mode) for
installation flexibility.

Specifications

Technology

Standards IEEE802.3, 802.3u, 802.3x, 802.1D, 802.1w,

802.1Q, 802.1p, 802.1X, 802.3ad, 802.3af/at

Protocols IGMPv1/v2, GVRP, SNMPv1/v2c/v3, DHCP

Server/Client, BootP, TFTP, SNTP, SMTP, RARP,
GMRP, LACP, RMON, HTTP, HTTPS, Telnet,
Syslog, DHCP Option 66/67/82, SSH, SNMP
Inform, Modbus/TCP, LLDP, IEEE 1588 PTP, IPv6

MIB MIB-II, Ethernet-Like MIB, P-BRIDGE MIB,

Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON
MIB Group 1,2,3,9

Processing Type Store and Forward

Flow Control IEEE802.3x flow control, back pressure flow control

SC Connector

ST Connector

— 13 —

Interface

RJ45 Ports 10/100BaseT(X) auto negotiation speed, F/H duplex

mode, and auto MDI/MDI-X connection

Fiber Ports 100BaseFX ports (SC/ST connector)

Console RS-232 (RJ45)

LED Indicators PWR1, PWR2, FAULT, 10/100M (TP port), 100M

(fiber port), MSTR/HEAD and CPLR/TAIL, PoE

Relay Contact Two relay outputs with current carrying capacity of

1 A @ 24 VDC

DIP Switches Master, Coupler, Turbo Ring, Reserve

Digital Input Two inputs with the same ground, but electrically

isolated from the electronics

• For state “1”: +13 to +30 V

• For state “0”: -30 to +3 V

• Max. input current: 8 mA

Optical Fiber

Multi-mode Single-mode

Wavelength 1300 nm 1310 nm

Max. Tx -10 dBm 0 dBm

Min. Tx -20 dBm -5 dBm

Rx Sensitivity -32 dBm -34 dBm

Link Budget 12 dB 29 dB

Typical Distance

5 km

a

4 km

b

40 km

c

Saturation -6 dBm -3 dBm

a. using [50/125 μm, 800 MHz*km] cable
b. using [62.5/125 μm, 500 MHz*km] cable
c. using 9/125 μm cable

Power

Input Voltage 24/48 DC

Input Current Max. 7.8 A @ 24 VDC (supports up to 4 ports at 30

watts per PoE port)

Overload current
Protection

Present

Connection 2 removable 6-contact terminal blocks

Reverse Polarity
Protection

Present

Physical Characteristics

Casing IP30 protection, metal case

Dimensions 80 x 135 x 131.5 mm (3.15 x 5.31 x 5.18 in)

Weight 1270 g

Installation DIN-Rail, Wall Mounting (optional kit)

— 14 —

Environmental

Operating Temperature 0 to 60°C (32 to 140°F),

-40 to 75°C (-40 to 167°F ) for -T models

Storage Temperature -40 to 85°C (-40 to 185°F)

Ambient Relative
Humidity

5 to 95% (non-condensing)

Regulatory Approvals

Safety UL 508 (Pending)

EMI FCC Part 15, CISPR (EN55022) class A

EMS EN61000-4-2 (ESD), Level 3

EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 3
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8

Shock IEC60068-2-27

Freefall IEC60068-2-32

Vibration IEC60068-2-6

WARRANTY 5 years

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:
Toll-free: 1-888-669-2872
Tel: [phone]
Fax: [phone]

Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: [phone]
Fax: [phone]

Moxa Europe:
Tel: [phone]
Fax: [phone]

Moxa Asia-Pacific:
Tel: [phone]
Fax: [phone]