Moxa Technologies EDS-516A Installation Manual

MOXA EtherDevice™ Switch

EDS-516A Series Hardware Installation Guide

First Edition, November 2006

Moxa Networking Co., Ltd.

Tel: [phone]
Fax: [phone]

www.moxa.com
[e-mail] (Worldwide)

[e-mail] (The Americas)

P/N: 1802005160000

— 1 —

Package Checklist

MOXA EtherDevice™ Switch is shipped with the following items. If any of

these items are missing or damaged, please contact your customer service

representative for assistance.

y 1 MOXA EtherDevice Switch EDS-516A

y Hardware Installation Guide

y CD-ROM with User’s Manual and Windows Utility

y Moxa Product Warranty Booklet

y RJ45 to DB9 Console port cable

y Protective caps for unused ports
y Panel mounting kit (optional—must order separately)

Optional Accessories

y DR-4524—45W/2A DIN-Rail 24 VDC Power Supply with 85 to 264 VAC

input

y DR-75-24—75W/3.2A DIN-Rail 24 VDC Power Supply with 85 to 264

VAC input

y DR-120-24—120W/5A DIN-Rail 24 VDC Power Supply with 88 to 132

VAC/176 to 264 VAC input by switch

y EDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server

Software and manual

y WK-46—Wall Mounting Kit

— 2 —

Panel Views of EDS-516A

9

12

15

6

6

6

6

10
11

13

14

7

8

16

17

16

1

3

2

4

5

1. Grounding screw

2. Console port

3. Heat dissipation orifices

4. 6-pin terminal block for DI 1, DI 2,

and PWR 2

5. 6-pin terminal block for PWR1,

Relay 1, and Relay 2

6. 10/100BaseT(X), ports 1 to 16

7. PWR 1: LED for power input 1

8. PWR 2: LED for power input 2

9. Fault LED

10. MASTER LED

11. COUPLER LED

12. Turbo Ring logo

13. TP port’s 100 Mbps LED

14. TP port’s 10 Mbps LED

15. Model Name

16. Screw hole for Wall Mounting Kit

17. DIN-Rail Kit

— 3 —

Panel Views of EDS-516A (SC/ST Type)

9

12

15

6

6

10
11

13

14

7

8

19

20

19

1

3

2

4

5

17

16
18

18

NOTE:
The appearance of EDS-516A-MM-ST
is identical to EDS-516A-MM-SC.

1. Grounding screw

2. Console port

3. Heat dissipation orifices

4. 6-pin terminal block for DI 1, DI 2,

and PWR 2

5. 6-pin terminal block for PWR1,

Relay 1, and Relay 2

6. 10/100BaseT(X), ports 1 to 14

7. PWR 1: LED for power input 1

8. PWR 2: LED for power input 2

9. Fault LED

10. MASTER LED

11. COUPLER LED

12. Turbo Ring logo

13. TP port’s 100 Mbps LED

14. TP port’s 10 Mbps LED

15. Model Name

16. 100BaseFX Port 15

17. 100BaseFX Port 16

18. 100BaseFX LEDs

19. Screw hole for Wall Mounting Kit

20. DIN-Rail Kit

— 4 —

Mounting Dimensions (unit = mm)

PWR1

PWR2

FAULT

MASTER

COUPLER

100M

TX

13

11

9

14

12

10

7

5

3

8

6

4

1

2

100M

10M

TX

RX

16

RX

15

100M

Rear View

Side View

Front View

Wall Mounting Kit

DlN-Rail Kit

DlN-Rail Kit

DlN-Rail

127.52

46

70

7.75

30.50

7.75

9

36.9113.4

35.00

30.00

135.00

135.00

0.79

71.01

15.00

86.80

135.00

7.5 55 7.5

27.20

48.30

3.5

6

13.9

18.2

6

13.9

10
10

5

66.80

57.05

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of EDS-516A when you take it out of the box. If you need to reattach
the DIN-Rail attachment plate to EDS-516A, make sure the stiff metal spring
is situated towards the top, as shown by the following figures.

STEP 1—Insert the top of the

DIN-Rail into the slot just below the
stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown by
the following illustration.

metal
spring

DIN-Rail

metal
spring

DIN-Rail

To remove EDS-516A from the DIN-Rail, simply reverse Steps 1 and 2 above.

— 5 —

Wall Mounting (Optional)

For some applications, you will find it convenient to mount MOXA
EDS-516A on the wall, as shown by the following illustrations:

STEP 1—Remove the

aluminum DIN-Rail
attachment plate from the
MOXA EDS-516A rear
panel, and then attach the
wall mount plates, as shown
by the figure on the right.

Top
plate

Bottom
plate

STEP 2—Mounting MOXA EDS-516A on the wall requires 4

screws. Use the EDS-516A, with wall mount plates attached, as a
guide to mark the correct locations of the 4 screws. The heads of
the screws should be less than 6.0 mm in diameter, and the shafts
should be less than 3.5 mm in diameter, as shown by the figure

on the right.

6.0 mm

3.5 mm

NOTE

Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the
way—leave about 2 mm to allow
room for sliding the wall mount
panel between the wall and the
screws.

STEP 3—Once the screws are fixed
on the wall, insert the four screw

heads through the wide parts of the
keyhole-shaped apertures, and then
slide EDS-516A downwards, as
indicated by the figure on the right.
Tighten the four screws for more
stability.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been
switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.

— 6 —

ATTENTION

This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or
wiring your MOXA EtherDevice Switch.

Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the maximum
current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.

You should also pay attention to the following points:

y Use separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point

y NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately

y You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together

y Separate input wiring and output wiring

y We advise that you label wiring to all devices in the system when

necessary.

Grounding MOXA EDS-516A

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

EDS-516A has two sets of relay outputs—relay 1 and relay 2. Each Relay
Contact consists of the two contacts of the terminal block on EDS-516A’s top
panel. You can refer to the next section for detailed instructions on how to
connect the wires to the terminal block connector, and how to attach the
terminal block connector to the terminal block receptor.

In this section, we will explain the meaning of the two contacts used to
connect the Relay Contact.

— 7 —

Relay1 Relay2

Relay1 Relay2

FAULT:

The two sets of relay contacts of
the 6-pin terminal block connector
are used to detect user-configured
events. The two wires attached to
the Fault contacts form an open
circuit when a user-configured
event is triggered. If a
user-configured event does not

occur, the Fault circuit remains

closed.

Wiring the Redundant Power Inputs

EDS-516A has two sets of power inputs—power input 1 and power input

2.The top two contacts and the bottom two contacts of the 6-pin terminal
block connector on EDS’ top panel are used for EDS’ two digital inputs. The
top and front views of one of the terminal block connectors are shown here.

PWR1

PWR2

V1- V1+

PWR1

V2- V2+

PWR2

V1- V1+ V2- V2+

STEP 1: Insert the

negative/positive DC wires into the
V-/V+ terminals, respectively.

STEP 2: To keep the DC wires

from pulling loose, use a small
flat-blade screwdriver to tighten
the wire-clamp screws on the front
of the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the
terminal block receptor, which is
located on EDS-516A’s top panel.

Wiring the Digital Inputs

EDS-516A has two sets of digital inputs, DI 1 and DI 2. Each DI consists of
two contacts of the 6-pin terminal block connector on EDS’s top panel, which
are used for EDS’s two DC inputs. The top and front views of one of the
terminal block connectors are shown here.

I1

D2I

I2

D1I

I1 I2

D2ID1I

STEP 1: Insert the negative

(ground)/positive DI wires into the
┴/I1 terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade
screwdriver to tighten the
wire-clamp screws on the front of
the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the
terminal block receptor, which is

located on EDS-516A’s top panel.

— 8 —

Communication Connections

All models of EDS-516A have one RJ45 console port (RS-232 interface),
between 14 and 16 10/100BaseTX Ethernet ports. Some models also have 2
100BaseFX (SC/ST-type connector) fiber ports.

In this section, we present two types of diagrams—Pinout Diagrams and
Cable Wiring Diagrams—to convey information about the ports and the
cables used to connect MOXA EDS-516A to other devices:

Pinouts—The meaning of the “Pinouts” diagrams is straightforward. The
diagrams simply display the type of signal passing through each of the port’s
pins.

Cable Wiring—Diagrams labeled “Cable Wiring” present standard cable
wiring schemes for cables used to connect MOXA EtherDevice Switch’s ports
to other devices. These diagrams display three pieces of information:

1. When building your own cable, refer to the “pin-to-pin” Cable Wiring

information displayed between the two vertical dashed lines to see which
pin of the connector on the left should be connected to which pin of the
connector on the right.

2. The information to the left of the left vertical dashed lines gives the

pinouts of the relevant MOXA EtherDevice Switch port.

3. The information to the right of the right vertical dashed line gives the

pinouts of the opposing device’s port.

NOTE

1. The pin numbers for male DB9 and DB25 connectors, and

hole numbers for female DB9 and DB25 connectors are
labeled on the connector. However, the numbers are typically
quite small, so you may need to use a magnifying glass to see
the numbers clearly.

2. The pin numbers for both 8-pin and 10-pin RJ45 connectors

(and ports) are typically not labeled on the connector (or port).
Refer to the following Pinout and Cable Wiring diagrams to
see how RJ45 pins are numbered

— 9 —

RS-232 Connection

MOXA EDS-516A has one RS-232 (10-pin RJ45) console port, located on the
top panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable (see the cable
following wiring diagrams) to connect MOXA EDS-516A’s console port to
your PC’s COM port. You may then use a console terminal program, such as
MOXA PComm Terminal Emulator, to access MOXA EDS-516A’s console
configuration utility.

RJ45 (10-pin) Console Port Pinouts

Pin Description

1 -----­2 DSR
3 -----­4 GND
5 TxD
6 RxD
7 GND
8 -----­9 DTR

10 ------

110

RJ45 (10-pin) to DB9 (F) Cable Wiring

RJ45 Plug Pin 1

Moxa

EtherDevice

Server

RJ45

Connector

DCD
DSR

RTS

GND

TxD
RxD
CTS
DTR

COM Port

Female DB9
Connector

DCD
DTR
CTS
GND
RxD
TxD
RTS
DSR

Cable Wiring

1
2
3

4/7

5
6
8
9

1
6
7
5
3
2
8
4

RJ45 (10-pin) to DB25 (F) Cable Wiring

RJ45 Plug Pin 1

Moxa

EtherDevice

Server

RJ45

Connector

DCD
DSR

RTS

GND

TxD
RxD
CTS
DTR

COM Port

Female DB2

5

Connector

DCD
DTR
CTS
GND
RxD
TxD
RTS
DSR

Cable Wiring

1
2
3

4/7

5
6
8
9

8
6
4
7
2
3
5
20

— 10 —

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on MOXA EtherDevice Switch’s front
panel are used to connect to Ethernet-enabled devices. Most users will choose
to configure these ports for Auto MDI/MDI-X mode, in which case the port’s
pinouts are adjusted automatically depending on the type of Ethernet cable
used (straight-through or cross-over), and the type of device (NIC-type or
HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.

RJ45 (8-pin, MDI) Port Pinouts

Pin Signal

1 Tx+
2 Tx­3 Rx+
6 Rx-

1

8

RJ45 (8-pin, MDI-X) Port Pinouts

Pin Signal

1 Rx+
2 Rx­3 Tx+
6 Tx-

1

8

RJ45 (8-pin) to RJ45 (8-pin) Straight -Through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector

RJ45
Connecto

r

Tx+
Tx­Rx+
Rx-

NIC Port

Cable Wiring

3 3
6 6
1 1
2 2

Rx+
Rx­Tx+
Tx-

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port
(NIC Port)

RJ45

Connector

RJ45
Connector

Tx+
Tx­Rx+
Rx-

(Rx+)
(Rx-)
(Tx+)
(Tx-)

(Tx+)
(Tx-)
(Rx+)
(Rx-)

Switch Port
(NIC Port)

Cable Wiring

3 1
6 2
1 3
2 6

Rx+
Rx­Tx+
Tx-

— 11 —

100BaseFx Ethernet Port Connection

The concept behind the SC/ST port and cable is quite straightforward. Suppose
you are connecting devices I and II. As opposed to electrical signals, optical
signals do not require a circuit in order to transmit data. Consequently, one of
the optical lines is used to transmit data from device I to device II, and the
other optical line is used transmit data from device II to device I, for
full-duplex transmission.

All you need to remember is to connect the Tx (transmit) port of device I to the
Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II. If you are making your own cable, we suggest
labeling the two sides of the same line with the same letter (A-to-A and B-to-B,
as shown by the following illustration, or A1-to-A2 and B1-to-B2).

SC Port Pinouts SC-Port to SC-Port Cable Wiring

Tx

Rx

AA

BB

Cable Wiring

A A
B B

ST Port Pinouts ST-Port to ST-Port Cable Wiring

Tx

Rx

AA

B

Cable Wiring

A A
B B

B

ATTENTION

This is a Class 1 Laser/LED product. To prevent damage to your
eyes, do not stare directly into the laser beam.

— 12 —

LED Indicators

The front panel of MOXA EDS-516A contains several LED indicators. The

function of each LED is described in the following table:

LED Color State Description

On

Power is being supplied to power
input P1.

PWR1 AMBER

Off

Power is not being supplied to power

input P1.

On

Power is being supplied to power
input P2.

PWR2 AMBER

Off

Power is not being supplied to power

input P2.

On

When the corresponding PORT alarm
is enabled, and a user-configured
event is triggered.

FAULT RED

Off

When the corresponding PORT alarm
is enabled and a user-configured
event is not triggered, or when the
corresponding PORT alarm is
disabled.

On

When the EDS-516A is the Master of
this Turbo Ring

MASTER GREEN

Blinking

When the EDS-516A is Ring Master
of this Turbo Ring and the Turbo Ring
is broken.

On

When the EDS-516A enables the
coupling function to form a back-up
path.

COUPLER GREEN

Off

When the EDS-516A disables the
coupling function.

On

TP port’s 10 Mbps link is active.

Blinking

Data is being transmitted at 10 Mbps.

10M
(TP)

GREEN

Off

TP port’s 10 Mbps link is inactive.

On

TP port’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100
Mbps.

100M

(TP)

GREEN

Off

TP port’s 100 Mbps link is inactive.

On

FX port’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100
Mbps.

100M

(FX)

GREEN

Off

FX port’s 100 Mbps link is inactive.

— 13 —

Specifications

Technology

Standards IEEE802.3, 802.3u, 802.3x, 802.1D, 802.1w,

802.1Q, 802.1p, 802.1X, 802.3ad, 802.3z

Protocols IGMP V1/ V2/ V3 device, GMRP, GVRP, SNMP

V1/V2c/V3, DHCP Server/Client, BootP, TFTP,
SNTP, SMTP, RARP, RMON and EDS-SNMP
OPC Server Pro (Optional)

MIB MIB-II, Ethernet-Like MIB, P-BRIDGE MIB,

Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON
MIB Group 1,2,3,9

Interface

RJ45 Ports 10/100BaseT(X) auto negotiation speed, F/H duplex

mode, and auto MDI/MDI-X connection

Fiber Ports 100BaseFX (SC/ST connector)

Console RS-232 (RJ45)

LED Indicators PWR1, PWR2, FAULT, 10/100M (TP port), 100M

(Fiber port), Ring Master and Ring Coupler

Alarm Contact Two relay outputs with current carrying capacity of

1A @ 24 VDC

Digital Input Two inputs with the same ground, but electrically

isolated from the electronics

• For state “1”: +13 to +30V

• For state “0”: -30 to +3V

• Max. input current: 8 mA

Optical Fiber
Distance:

Multi mode: 0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km)

0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km)

Min. TX Output:

Multi mode : -20 dBm

Max. TX Output:

Multi mode : -14 dBm

Sensitivity:
Multi mode : -34 to -30 dBm

— 14 —

Power

Input Voltage 24 VDC(12 to 45 VDC), redundant inputs

Input Current (@24V) 0.31A: (EDS-516A)

0.39A: (EDS-516A-MM-SC/ST

)

Connection Two removable 6-pin terminal blocks

Overload Current
Protection Present

Reverse Polarity
Protection

Present

Mechanical

Casing IP30 protection, metal case

Dimensions 95 x 135 x 140 mm (W x H x D)

Weight 1.586 kg

Installation DIN-Rail, Wall Mounting (optional kit)

Environmental

Operating Temperature 0 to 60°C (32 to 140°F)

-40 to 75°C (-40 to 167°F) for -T models

Storage Temperature -40 to 85°C (-40 to 185°F)

Ambient Relative
Humidity

5% to 95% (non-condensing)

Regulatory Approvals

Safety UL 508 (Pending), UL60950-1,

CSA C22.2 No. 60950-1, EN60950-1

Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, and D,

ATEX Class I, Zone 2, EEx nC IIC (Pending)

EMI FCC Part 15, CISPR (EN55022) class A

EMS EN61000-4-2 (ESD), Level 3

EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 3
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8
EN61000-4-11
EN61000-4-12

Shock IEC60068-2-27

Freefall IEC60068-2-32

Vibration IEC60068-2-6

WARRANTY 5 years

— 15 —

MOXA Internet Services

Customer satisfaction is our number one concern. To ensure that customers
receive the full benefit of our products, Moxa has set up on-line support
services to provide technical support, driver updates, product information, and
user’s manual updates.

E-mail for technical support:

[e-mail] (Worldwide)

[e-mail] (The Americas)

Website for up to date product information:

www.moxa.com