Moxa Technologies EDS-305-M12 Hardware Installation Manual

MOXA EtherDevice Switch

EDS-305-M12

Hardware Installation Guide

First Edition, July 2007

Moxa Networking Co., Ltd.

Tel: [phone]
Fax: [phone]
www.moxa.com

[e-mail] (Worldwide)
[e-mail] (The Americas)

P/N:1802003050010

— 1 —

Overview

The MOXA EtherDevice™ EDS-305-M12 series of 5-port smart Ethernet
switches provides a hardened and cost-effective solution for your Ethernet
connections. The EDS-305-M12 switches are IP67-rated to provide protection
against shock and foreign particles. IP67-rated products have the following
characteristics: (1) dust proof, (2) protection against the effects of temporary
immersion in water.

The EDS-305-M12 switches have a wide operating temperature range of -40
to75°C, and are designed to withstand a high degree of vibration and shock.
The rugged hardware design makes the EDS-305-M12 switches perfect for
ensuring that your Ethernet equipment can withstand the rigors associated with
critical industrial applications. The switches are rated for use in hazardous
locations (Class 1 Division 2/Zone 2), and comply with CE, FCC, UL, DNC,
and GL Standards.

Package Checklist

Your EDS-305-M12 is shipped with the following items. If any of these items
is missing or damaged, please contact your customer service representative for
assistance.

y MOXA EtherDevice™ Switch
y Hardware Installation Guide
y Product Warranty Statement
y Protective caps for unused ports and 8 port labels

Features

High Performance Network Switching Technology

y 5 10/100BaseT(X) ports (4-pin shielded M12 socket with D coding)
y Broadcast storm protection
y IEEE802.3/802.3u/802.3x
y Store and Forward switching process type
y 10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing

Industrial Grade Reliability

y Active circuit protection
y Robust connection
y Dust and immersion proof

Rugged Design

y Casing design meets IP67 protection standards
y M12 connectors for robust connections
y Operating temperature range of 0 to 60°C, or extended operating

temperature range of -40 to 75°C

— 2 —

EDS-305-M12 Panel Layouts

Front Panel View

EDS-305-M12

1
2

3

5
4

6
8
7

8
7

7

1. M12 port’s 10/100 Mbps LED

2. 10/100BaseT(X) port (4-pin shielded M12 socket with D coding)

3. Port Label

4. Power input (5-pin shielded M12 socket with A coding)

5. Power input (PWR) LED

6. Model name

7. Holes for attaching the EDS-305-M12 to a wall with screws (there are 3

holes: bottom left, bottom right, and top middle)

8. Grounding screws

Mounting Dimensions (unit = mm)

Top View Side ViewFront View

— 3 —

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label. Check
the voltage of your power source to make sure that you are using
the correct voltage. Do NOT use a voltage greater than what is
specified on the product label.

These devices must be supplied by a SELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or
wiring your MOXA switch.

This device has UL508 approval. Use copper conductors only,
60/75°C, Tighten To 4.5 pound-inches

ATTENTION

Safety First!

Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. If the current goes
above the maximum ratings, the wiring could overheat, causing
serious damage to your equipment.

You should also heed the following guidelines:
y Use separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point. NOTE: Do not run signal or communications
wiring and power wiring in the same wire conduit. To avoid interference,
wires with different signal characteristics should be routed separately.

y You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.

y Keep input wiring and output wiring separated.
y It is strongly advised that you label wiring to all devices in the system when

necessary.

Grounding the EDS-305-M12

Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

— 4 —

ATTENTION

This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.

10/100BaseT(X) Ethernet Port
Connection

All EDS-305-M12 models have 5 10/100BaseT(X) Ethernet ports (4-pin
shielded M12 socket with D coding). The 10/100TX ports located on the
EDS-305-M12’s front panel are used to connect to Ethernet-enabled devices.
Most users configure these ports for Auto MDI/MDI-X mode, in which case
the port’s pinouts are adjusted automatically depending on the type of Ethernet
cable used (straight-through or cross-over), and the type of device (NIC-type or
HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.

Pinouts for sockets on EDS-305-M12
Tx port

1

4

3

2

-Pin 1:

-Pin 2:

-Pin 3:

-Pin 4:

Tx +
Rx +
Tx ­Rx -

Power input

1

4

3

2

5

-Pin 1:

-Pin 2:

-Pin 3:

-Pin 4:

-Pin 5:

Input V+
Not assigned
Input V­Not assigned
Function ground

MDI Port Pinouts MDI-X Port Pinouts 8-Pin RJ45

Pin Signal

1 Tx +
2 Tx ­3 Rx +
6 Rx -

Pin Signal

1 Rx +
2 Rx ­3 Tx +
6 Tx -

18

— 5 —

M12 (4-pin) to M12 (4-pin)

Tx+
Rx+
Tx­Rx-

Cable Wiring

1   2
2    1
3   4
4   3

Rx+
Tx+
Rx­Tx-

M12 (4-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Straight-Through Cable

Tx+
Rx+
Tx­Rx-

Cable Wiring

1   1
2    3
3   2
4   6

Tx+
Rx+
Tx­Rx-

M12 (4-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Cross-Over Cable

Tx+
Rx+
Tx­Rx-

Cable Wiring

1   3
2    1
3   6
4   2

Tx+
Rx+
Tx­Rx-

Dual Speed Functionality & Switching

The EDS-305-M12’s 10/100 Mbps switched M12 ports auto negotiate with the
connected device to use the fastest data transmission rate supported by both
devices. All of MOXA’s EtherDevice switches are plug-and-play devices, so
that software configuration is not required. The half/full duplex mode for the
switched M12 ports is user dependent and changes (by auto-negotiation) to full
or half duplex, depending on which transmission speed is supported by the
attached device.

— 6 —

Switching and Address Learning

The EDS-305-M12 has an address table that can hold up to 1000 node
addresses, which makes it suitable for use with large networks. The address
tables are self-learning, so that as nodes are added or removed, or moved from
one segment to another, the EDS-305-M12 automatically keeps up with new
node locations. An address-aging algorithm causes the least-used addresses to
be deleted in favor of newer, more frequently used addresses. To reset the
address buffer, power down the unit and then power it back up.

Switching, Filtering, and Forwarding

Each time a packet arrives at one of the switched ports, a decision is made to
filter or forward the packet. Packets with source and destination addresses
belonging to the same port segment will be filtered, constraining those packets
to one port, and relieving the rest of the network from the need to process them.
A packet with destination address on another port segment will be forwarded to
the appropriate port, and will not be sent to the other ports where it is not
needed. Packets that are used in maintaining the operation of the network (such
as the occasional multi-cast packet) are forwarded to all ports.

The EDS-305-M12 operates in the store-and-forward switching mode, which
eliminates bad packets and enables peak performance to be achieved when
there is heavy traffic on the network.

LED Indicators

Several LED indicators are located on the EDS-305-M12’s front panel. The
function of each LED is described in the table below.

LED Color State Description

On

Power is being supplied to the power
input.

PWR AMBER

Off

Power is not being supplied to the
power input.

On TP port’s 10 Mbps link is active.

Blinking Data is being transmitted at 10 Mbps

LNK/ACT

(10M)

AMBER

Off TP port’s 10 Mbps link is inactive.
On TP port’s 100 Mbps link is active

Blinking

Data is being transmitted at 100
Mbps.

LNK/ACT

(100M)

GREEN

Off TP port’s 100 Mbps link is inactive.

— 7 —

Auto-Negotiation and Speed Sensing

All of the EDS-305-M12’s Ethernet ports independently support
auto-negotiation for speeds in the 10BaseT and 100BaseTX modes, with
operation according to the IEEE 802.3u standard. This means that some nodes
could be operating at 10 Mbps, while at the same time, other nodes are
operating at 100 Mbps.

Auto-negotiation takes place when an M12 cable connection is made, and then
each time a LINK is enabled. The EDS-305-M12 advertises its capability for
using either 10 Mbps or 100 Mbps transmission speeds, with the device at the
other end of the cable expected to advertise in the same way. Depending on
what type of device is connected, this will result in agreement to operate at a
speed of either 10 Mbps or 100 Mbps.

If an EDS-305-M12’s Ethernet port is connected to a non-negotiating device, it
will default to 10 Mbps speed and half-duplex mode, as required by the IEEE

802.3u standard.

Specifications

Technology

Standards IEEE 802.3, 802.3u, 802.3x
Processing Type Store and Forward, with IEEE802.3x full duplex,

back pressure flow control

Interface

M12 Ports 10/100BaseTX auto negotiation speed, F/H duplex

mode, and auto MDI/MDI-X connection
LED Indicators Power, LNK/ACT
Power
Input Voltage 12 to 45 VDC or 18 to 30 VAC (47 to 63 Hz)
Input Current 0.13A @ 24 VDC

0.28A @ 24 VAC

Connection One M12 socket (A-coding), single power input

Protection

Overload current
protection / Limited
current

1.1A

Reverse polarity
protection

present

Mechanical

Casing IP67 protection, plastic case
Dimensions (W x H x

D)

60 x 125 x 29.6 mm (2.4 x 4.9 x 1.2 in)

Weight 250g
Installation Field-style mounting

Environment

Operating Temperature 0 to 60°C for standard model,

-40 to 75°C for -T models
Storage Temperature -40 to 85ºC
Operating relative

humidity

5 to 95%

(non-condensing)

— 8 —

MTBF > 200,000 hours

Regulatory Approvals

Safety UL 508 (pending)
Hazardous Location UL/cUL Class1, Div.2, ATEX Class1, Zone2

(pending)

Maritime DNV, GL (pending)

EMI: FCC Part 15, CISPR (EN55022) class A
EMS: EN61000-4-2 (ESD), level 3
EN61000-4-3 (RS), level 3
EN61000-4-4 (EFT), level 3
EN61000-4-5 (Surge), level 3
EN61000-4-6 (CS), level 2
Shock: IEC60068-2-27
Free Fall: IEC60068-2-32
Vibration: IEC60068-2-6

WARRANTY

5 years

MOXA Internet Services

Customer satisfaction is our number one concern, and to ensure that customers
receive the full benefit of our products, MOXA has set up on-line support
services to provide technical support, driver updates, product information, and
user’s manual updates.

E-mail for technical support:
[e-mail]

(Worldwide)

[e-mail]

(The Americas)

Website for up to date product
information:
www.moxa.com