Moxa Technologies CP-132UL, CP-114UL-I, CP-118U, CP-118U-I, CP-112UL Quick Installation Manual
...
– 1 – – 2 – – 3 –
P/N: 1802001142325
Universal PCI Smart Serial Board
Quick Installation Guide
First Edition, October 2017
Overview
Moxa’s Universal PCI (UPCI) multiport serial boards can be
installed in PC I or PCI-X slots and support both 3.3V and 5V
PCI/PCI-X.
Package Checklist
UFCI board are sh ipped with the following ite ms:
• 1 Moxa UPCI multiport se rial board
• Low-profile bracke t (low-profile models only)
• Documentation and software CD
• Quick installation guide (printed)
• Warranty card
NOTE
Notify your sales representative if any of the above items
are missing or damaged.
Hardware Installation Procedure
The Universal P CI board MUST be plugged into the PC before the
driver is instal led.
Follow the steps below:
1. Select serial transmission mode. This step is for certain
models listed below.If your product on hand is not included,
please directly go to step2.
If your model is CP-112UL Series / CP-114UL Ser ies / CP-118U
Series/ CP-132UL Series/ CP-134U Series/ CP-138 U Series,
you will need to set onboard DIP switches for each port.
(Refer to “Dip Switch Settings” section to complete the DIP
switches setting)
2. Install the boa rd. Power off the PC and then plug the board
firmly into any open PCI or PCI-X expansion slot.
3. Plug the connection cable into the board’s connector.
(Refer to “Pin Assignments” section for the cable pin
assignment).
4. Start system and verify the driver initialization.
Software Installation Information
1. Get the driver at www.moxa.com or from the CD. Ba sed
on the OS type, choose the corresponding driver.
2. Installing the driver:
• For Window s OS (Take the installation of Win7 as
an example)
o 2.1. Unzip and execute the .exe file
o 2.2. Follow the instruction s to install the
drivers
• For Linux
Execute the following commands from the Linux
prompt:
o 2.1. Get the driver from CD and Unzip the
file:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver
directory>/mxser. tgz .
#tar xvfz mxser.tgz
o 2.2. Install th e driver:
#cd mxser
#./mxinstall
o 2.3. Verify the driver status
Use the Moxa diagnostic utility to verify
the driver statu s:
#cd /moxa/mxser/utility/diag
#./msdiag
o 2.4. Test the tty port
Use the Moxa terminal utility to test the
tty ports:
#cd /moxa/mxser/utility/term
#./msterm
DIP Switch Settings
CP-112UL Series /CP-112UL-I Series
Mode
S1
S2
S3
RS-232
ON - -
RS-422
OFF
ON - 4-Wire RS-485
OFF
OFF
ON
2-Wire RS-485
OFF
OFF
OFF
CP-114UL Series /CP-114UL-I Seri es
Mode
S1
S2
S3
RS-232
- - ON
RS-422
-
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-118U Series /CP-118U-I Series
Mode
S1
S2
S3
RS-232
- - ON
RS-422
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-132UL Series
Mode
S1
S2
Illustration
RS-422
-
OFF
2-Wire RS-485 ON ON
4-Wire RS-485
OFF
ONN
CP-134U Series /CP-134U-I Series
RS-422 or RS-485 mode:
Use the jumpe r to cover th e
two column s on the left of the
jumper pins.
RS-232 mode: Use the
jumper to c over the tw o
columns on the ri ght of the
jumper pins.
– 4 – – 5 – – 6 –
CP-138U Series /CP-138U-I Series
Mode
S1
S2
RS-422
ON
4-Wire RS-485
ON
OFF
2-Wire RS-485
OFF
OFF
Pin Assignments
CP-102U Series
Male DB9 RS-232
Pin
Signal 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS
CP-102UL Series
Female DB25 RS-232
Pin
Signal
Pin
Signal
1 - 14
-
2
DCD1
15
DTR1 3 GND
16
DSR1
4
CTS1
17
RTS1
5
RxD1
18
TxD1 6 -
19
-
7 - 20
–
8 - 21
DCD0 9 DTR0
22
GND
10
DSR0
23
CTS0
11
RTS0
24
RxD0
12
TxD0
25
13 - -
-
CP-104JU Series
RJ45(RS-232)
Pin
Signal 1 DSR 2 RTS 3 GND 4 TxD 5 RxD 6 DCD 7 CTS 8 DTR
CP-104UL
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
2
TxD
3
RxD
4
RTS 5 CTS
6
DSR
7
GND 8 DCD
20
DTR
(CBL-M44M9x4-50)
(Opt4-M9 A)
Pin
RS-232
1
DCD
2
RxD 3 TxD
4
DTR
5
GND 6 DSR
7
RTS
8
CTS
RJ45(Opt4-RJ45A)
Pin
RS-232
1
DSR 2 RTS
3
GND
4
TxD 5 RxD
6
DCD
7
CTS 8 DTR
CP-112UL-Series
Male DB9 (CBL-M25M9x2-50)
Pin RS-232 RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
-
2
RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data+(A)
5
GND
GND
GND 6 DSR - -
7
RTS - –
8
CTS - - 9 - - -
CP-114UL Series
Male DB9 (CBL-M44M9x4-50)
Pin
RS-232
RS-422/485-4W
RS-485-2W
1
DCD
TxD-(A)
– 2 RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND 6 DSR – – 7 RTS – – 8 CTS ––
– 7 – – 8 – – 9 –
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS – –
5
CTS – – 6 DSR – –
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
CP-118UI Series/CP-138U-I Series
Male DB9 (CBL-M78M9x8-100)
Pin
RS-232*
RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
– 2 RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND 6 DSR – – 7 RTS – – 8 CTS – –
*CP-118U-I Series only
Male DB25 (CBL-M78M25x8-100)
Pin
RS-232*
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
– 4 RTS – – 5 CTS – – 6 DSR – – 7 GND
GND
GND 8 DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
*CP-118U-I
Series only
CP-118U Series/CP-138U Series
Male DB9
(CBL-M62M9x8-100, Opt8-M9 is for CP-118U and CP-138U)
(CBL-M78M9x8-100 is for CP-118U-I a nd CP-138U-I)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND 6 DSR – –
7
RTS – –
8
CTS – –
*CP-118U Series only
Male DB25
(CBL-M62M25x8-100, Opt8B is for CP-118U and CP- 138U)
(CBL-M78M25x8-100 is for CP-118U-I and CP-138U-I)
Pin
RS-232*
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS – –
5
CTS – – 6 DSR – –
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
*CP-118U S
eries only
Female DB25 (OPT8A/S)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
CTS – –
5
RTS – –
6
DTR
RxD-(A)
Data-(A)
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DSR – –
*CP-118U S
eries only
RJ45 (opt8- RJ45)
Pin
Signal*
1
DSR 2 RTS 3 GND 4 TxD 5 RxD 6 DCD 7 CTS 8 DTR
*CP-118U Se
ries onl
CP-132UL Series/CP-132UL-I Series
Male DB9 Connector: Device-side Pin Assignments
Pin
RS-422
RS-485-4W
RS-485-2W
1
TxD-(A)
TxD-(A)
– 2 TxD+(B)
TxD+(B)
– 3 RxD+(B)
RxD+(B)
Data+(B)
4
RxD-(A)
RxD-(A)
Data-(A)
5
GND
RxD-(A)
GND 6 RTS-(A)
GND – 7
RTS+(B)
– – 8
CTS+(B)
– – 9
CTS-(A)
–
–
– 10 – –11- – 12 –
www.moxa.com/support
The Americas:
+1-714-528-6777 (toll-free: 1-888-669-2872)
Europe:
+49-89-3 70 03 99-0
Asia-Pacific:
+886-2-8919-1230
China:
+86-21-5258-9955 (toll-free: 800-820-5036)
2017 Moxa Inc. All rights reserved.
CP-134U Series
Male DB9 (CBL-M44M9x4-50)
Pin
RS-232
RS-422/
RS-485-
4W
RS-485-
2W
1 DCD T xD-(A) TxD-(A) –
2 RxD TxD+(B) TxD+(B ) –
3 TxD RxD+(B) RxD+(B) Data
+(B)
4
DTR
RxD-(A)
RxD-(A)
Data
– (A)
5
GND
GND
GND
GND 6 DSR
RTS-(A)
– 7 RTS
RTS+(B)
– 8 CTS
CTS+(B)
–
9
CTS-(A)
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
RS-422/
RS-485-
4W
RS-485-
2W
2
TxD
RxD+(B)
RxD+(B)
Data
+(B)
3
RxD
TxD+(B)
TxD+(B)
–
4
RTS
RTS+(B)
-
5
CTS
CTS+(B)
- - 6
DSR
RTS-(A)
- - 7
GND
GND
GND
GND 8 DCD
TxD-(A)
TxD-(A)
–
20
DTR
RxD-(A)
RxD-(A)
Data
-(A)
22 - CTS-(A) - -
CP-168U Series
RS-232 Cable Wiring for Opt8A/B/C/D/S
OPT8A/S(DCE, DB25 Female)
Pin
Signal 2 RxD 3 TxD 4 CTS 5 RTS 6 DTR 7 GND 8 DCD
20
DSR
OPT8-RJ45 (8-pin)
Pin
Signal 1 DSR 2 RTS 3 TxD 4 GND 5 RxD 6 DCD 7 CTS 8 DTR
OPT8B
/C (DCE, DB25 Male)
Pin
Signal 2 TxD
3
RxD
4
RTS 5 CTS
6
DSR
7
GND 8 DCD
20
DTR
OPT8-M
9, Opt8D(DTE, DB9 Male)
Pin
Signal 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS
RS-422 Cable Wiring for Opt8F
OPT8F/Z(DB25 Female)
Pin
Signal 2 RxD+(B)
3
TxD+(B)
14
RxD-(A)
16
TxD-(A)
7
GND
RS-422/485 Cable Wiring for Opt8K
RS-422/
RS-485-4W
RS-485-2W
Pin
Signal
Pin
Signal 2 RxD+(B)
2
Data+(B)
3
TxD+(B)
14
Data-(A)
14
RxD-(A)
7
GND
16
TxD-(A)
7
GND
POS-104UL Series
Male D89(CBL-M44M9x4-50)
Pin
RS-232
1
DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI/5V/12V
Loading...