Moxa Technologies CP-132UL, CP-114UL-I, CP-118U, CP-118U-I, CP-112UL Quick Installation Manual
...
– 1 – – 2 – – 3 –
P/N: 1802001142325
Universal PCI Smart Serial Board
Quick Installation Guide
First Edition, October 2017
Overview
Moxa’s Universal PCI (UPCI) multiport serial boards can be
installed in PC I or PCI-X slots and support both 3.3V and 5V
PCI/PCI-X.
Package Checklist
UFCI board are sh ipped with the following ite ms:
• 1 Moxa UPCI multiport se rial board
• Low-profile bracke t (low-profile models only)
• Documentation and software CD
• Quick installation guide (printed)
• Warranty card
NOTE
Notify your sales representative if any of the above items
are missing or damaged.
Hardware Installation Procedure
The Universal P CI board MUST be plugged into the PC before the
driver is instal led.
Follow the steps below:
1. Select serial transmission mode. This step is for certain
models listed below.If your product on hand is not included,
please directly go to step2.
If your model is CP-112UL Series / CP-114UL Ser ies / CP-118U
Series/ CP-132UL Series/ CP-134U Series/ CP-138 U Series,
you will need to set onboard DIP switches for each port.
(Refer to “Dip Switch Settings” section to complete the DIP
switches setting)
2. Install the boa rd. Power off the PC and then plug the board
firmly into any open PCI or PCI-X expansion slot.
3. Plug the connection cable into the board’s connector.
(Refer to “Pin Assignments” section for the cable pin
assignment).
4. Start system and verify the driver initialization.
Software Installation Information
1. Get the driver at www.moxa.com or from the CD. Ba sed
on the OS type, choose the corresponding driver.
2. Installing the driver:
• For Window s OS (Take the installation of Win7 as
an example)
o 2.1. Unzip and execute the .exe file
o 2.2. Follow the instruction s to install the
drivers
• For Linux
Execute the following commands from the Linux
prompt:
o 2.1. Get the driver from CD and Unzip the
file:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver
directory>/mxser. tgz .
#tar xvfz mxser.tgz
o 2.2. Install th e driver:
#cd mxser
#./mxinstall
o 2.3. Verify the driver status
Use the Moxa diagnostic utility to verify
the driver statu s:
#cd /moxa/mxser/utility/diag
#./msdiag
o 2.4. Test the tty port
Use the Moxa terminal utility to test the
tty ports:
#cd /moxa/mxser/utility/term
#./msterm
DIP Switch Settings
CP-112UL Series /CP-112UL-I Series
Mode
S1
S2
S3
RS-232
ON - -
RS-422
OFF
ON - 4-Wire RS-485
OFF
OFF
ON
2-Wire RS-485
OFF
OFF
OFF
CP-114UL Series /CP-114UL-I Seri es
Mode
S1
S2
S3
RS-232
- - ON
RS-422
-
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-118U Series /CP-118U-I Series
Mode
S1
S2
S3
RS-232
- - ON
RS-422
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-132UL Series
Mode
S1
S2
Illustration
RS-422
-
OFF
2-Wire RS-485 ON ON
4-Wire RS-485
OFF
ONN
CP-134U Series /CP-134U-I Series
RS-422 or RS-485 mode:
Use the jumpe r to cover th e
two column s on the left of the
jumper pins.
RS-232 mode: Use the
jumper to c over the tw o
columns on the ri ght of the
jumper pins.
– 4 – – 5 – – 6 –
CP-138U Series /CP-138U-I Series
Mode
S1
S2
RS-422
ON
4-Wire RS-485
ON
OFF
2-Wire RS-485
OFF
OFF
Pin Assignments
CP-102U Series
Male DB9 RS-232
Pin
Signal 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS
CP-102UL Series
Female DB25 RS-232
Pin
Signal
Pin
Signal
1 - 14
-
2
DCD1
15
DTR1 3 GND
16
DSR1
4
CTS1
17
RTS1
5
RxD1
18
TxD1 6 -
19
-
7 - 20
–
8 - 21
DCD0 9 DTR0
22
GND
10
DSR0
23
CTS0
11
RTS0
24
RxD0
12
TxD0
25
13 - -
-
CP-104JU Series
RJ45(RS-232)
Pin
Signal 1 DSR 2 RTS 3 GND 4 TxD 5 RxD 6 DCD 7 CTS 8 DTR
CP-104UL
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
2
TxD
3
RxD
4
RTS 5 CTS
6
DSR
7
GND 8 DCD
20
DTR
(CBL-M44M9x4-50)
(Opt4-M9 A)
Pin
RS-232
1
DCD
2
RxD 3 TxD
4
DTR
5
GND 6 DSR
7
RTS
8
CTS
RJ45(Opt4-RJ45A)
Pin
RS-232
1
DSR 2 RTS
3
GND
4
TxD 5 RxD
6
DCD
7
CTS 8 DTR
CP-112UL-Series
Male DB9 (CBL-M25M9x2-50)
Pin RS-232 RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
-
2
RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data+(A)
5
GND
GND
GND 6 DSR - -
7
RTS - –
8
CTS - - 9 - - -
CP-114UL Series
Male DB9 (CBL-M44M9x4-50)
Pin
RS-232
RS-422/485-4W
RS-485-2W
1
DCD
TxD-(A)
– 2 RxD
TxD+(B)
– 3 TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND 6 DSR – – 7 RTS – – 8 CTS ––
Loading...