Moxa Technologies AWK-4131 Quick Installation Manual

P/N: 1802041310011

*1802041310011*

AWK-4131

Quick Installation Guide

Moxa AirWorks

Edition 2.0, July 2016

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:
Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):
Toll

-free: 800-820-5036

Tel:

[phone]

Fax:

[phone]

Moxa Europe:
Tel:

[phone]

Fax:

[phone]

Moxa Asia-Pacific:
Tel:

[phone]

Fax:

[phone]

Moxa India:
Tel:

[phone]

Fax:

[phone]



2016 Moxa Inc. All rights reserved.

- 2 -

Notes for the Reader

WARNING

I

ndicates that death or personal injury may occur if proper

precautions are not taken.

ATTENTION

Indicates that possible damage to this product or your property
may result if proper precautions are not taken.

NOTE

Highlights important information related to this product.

Package Checklist

Moxa’s AWK-4131 is shipped with the following items. If any of these
items is missing or damaged, please contact your customer service
representative for assistance.

• AWK-4131

• 2 omni-directional antennas (5/2 dBi, N-type male, 2.4/5 GHz)

• Wall-mounting kit (includes 2 supports)

• Field-installable power plug

• Field-installable M12 8-pin male plug for Ethernet

• Metal cap to cover M12 male DI/O connector

• Metal cap to cover RJ45 connector

• Meta cap to cover M30 SFP connector

• Documentation and software CD

• Quick installation guide (printed)

• Warranty card

- 3 -

Recommended SFP Accessories

SFP-1G series

• SFP-1GSXLC:
Small form factor pluggable transceiver with 1000BaseSX, LC, 0.5 km,
0 to 60°C.

• SFP-1GSXLC-T:
Small form factor pluggable transceiver with 1000BaseSX, LC, 0.5 km,

-20 to 75°C.

• SFP-1GLSXLC:
Small form factor pluggable transceiver with 1000BaseLSX, LC, 2 km,
0 to 60°C.

• SFP-1GLSXLC-T:
Small form factor pluggable transceiver with 1000BaseLSX, LC, 2 km,

-40 to 85°C.

• SFP-1GLXLC:
Small form factor pluggable transceiver with 1000BaseLX, LC, 10 km,
0 to 60°C.

• SFP-1GLXLC-T:
Small form factor pluggable transceiver with 1000BaseLX, LC, 10 km,

-40 to 85°C.

• SFP-1GLHLC:
Small form factor pluggable transceiver with 1000BaseLH, LC, 30 km,
0 to 60°C.

• SFP-1GLHLC-T:
Small form factor pluggable transceiver with 1000BaseLH, LC, 30 km,

-40 to 85°C.

• SFP-1GLHXLC:
Small form factor pluggable transceiver with 1000BaseLHX, LC, 40
km, 0 to 60°C.

• SFP-1GLHXLC-T:
Small form factor pluggable transceiver with 1000BaseLHX, LC, 40
km, -40 to 85°C.

• SFP-1GZXLC:
Small form factor pluggable transceiver with 1000BaseZX, LC, 80 km,
0 to 60°C.

• SFP-1GZXLC-T:
Small form factor pluggable transceiver with 1000BaseZX, LC, 80 km,

-40 to 85°C.

• SFP-1GEZXLC:
Small form factor pluggable transceiver with 1000BaseEZX, LC, 110
km, 0 to 60°C.

• SFP-1GEZXLC-120:
Small form factor pluggable transceiver with 1000BaseEZX, LC, 120
km, 0 to 60°C.

NOTE

The above items come with the AWK-4131 standard version. The
package contents for customized versions may be different.

- 4 -

Panel Layout of the AWK-4131

1. Main antenna A.

2. Main antenna B.

3. LEDs for PWR, FAULT,
STATE, WLAN and LAN.

4. M12 A-coding connector
for PWR1 and PWR2.

5. M12 8-pin male

connector

for DI/DO

6. M12 8-pin female
connector for Ethernet
port

7. SFP port

8. RS-232 console port.

9. Reset button

10.

Screw holes for wall

mounting

11.

Waterproof vent

12.

Grounding screw (M8)

13.

Screw holes for DIN-rail

mounting

ATTENTION

Please DO NOT open or remove the vent

(11)

. The warranty will
be invalid if the seal is removed.
All exposed co

nnectors, including 1, 2, 4 - 9, should be tightly

covered by suitable caps when they are not in use.

- 5 -

Dimensions

Attaching Antennas

The AWK-4131 includes two dual-band omni-directional antennas by
default. Attach the antennas as illustrated below:

Step 1: Use your fingers and hold the antenna metal N-type connector.

Step 2: Screw the antenna N-type connector (male) onto the AWK-4131

device’s N-type connector (female)

Caution

Do not hold the rubber plate to screw the antenna on to the
AWK-4131 device.

ATTENTION

Use the antennas correctly: Use 2.4

GHz antennas if the

AWK

-4131 operates in IEEE 802.11b/g/n. Use the 5 GHz

antennas for operations in IEEE802.11a

/n. Make sure your

antenna installation is within a safe area covered by a lightning
protection or surge arrest system.

Antenna Metal N-type

Rubber plate

- 6 -

Wall Mounting

In most applications, wall mount provides an easier installation. You will
find it quite easy to mount AWK-4131 on the wall, as illustrated below.

STEP 1:

Attach the wall

-mounting kit

with M4 screws, as shown in
the diagram below.

STEP 2:
Mounting the AWK

-4131 on the wall

requires 4 screws. Use the AWK

-4131

device, with wall

-mounting kit

attached, as a guide to mark the correct
locations of the 4 screws. The heads of
the screws are recommended to be
between 5.5mm and 8.5 mm in
diameter, and the shafts should not be

more than 5.0 mm
in diameter, as
shown in the figure.

Do not drive the screws in all the way in to the wall—leave a space of
about 2 mm to allow room for sliding the wall-mounting kit between the
wall and the screws.

ATTENTION

T

est the screw head and shank size by inserting the screws

into
one of the keyhole shaped apertures of the wall-mounting plates
before attaching the plates to the wall.

STEP 3:

Once the screws are fixed into the wall, insert the four screw heads
through the large opening of the keyhole-shaped apertures, and then
slide the AWK-4131 downwards, as indicated to the right. Tighten the
four screws for added stability.

ATTENTION

To avoid environmental vibration or shock, you can consider a
robust

installation with four bigger screws, the shafts of which

are
between 7.0 mm and 8.5 mm in diameter, and fix the AWK-4131
directly on to the wall.