The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their res pec tive manufacturers.
Disclaimer
Information in this document is subject to cha nge witho ut no tic e and doe s no t repres e nt a commitme nt o n the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the rig ht to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, a t any time .
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that m ay res ult fr om its use.
This product might include unintentional tec hnic al o r typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publica tio n.
2. Chapter Title ..................................................................................................................................... 2-1
End Product Labeling ........................................................................................................................... 3-2
Information for OEM and Integrators ..................................................................................................... 3-3
Antenna List ....................................................................................................................................... 3-3
1
1. Introduction
The MiiNePort W1 series provides serial to 802.11 b/g embedded wireless solution with compact size, and ultra
low power consumption features. Numerous operation modes are designed to fulfill the requirements of
embedded module application. Complete driv er support reduces software redesign effort and acc elerat e time
to market.
The MiiNePort W1 series is a very compact module that installs in a serial device to connect it to a wireless LAN.
With such a small size, around half the size of a credit card., it can be installed into almost any kind of serial
device. The MiiNePort W1 series also comes with a built-in TCP/IP stack for fast integration with your serial
devices. This means that your engineers can spend less time with the TCP/IP and wireless details, and more
time on developing major features , shortening your product’s time to market. The reliable TCP/IP
communication firmware can be configured easily using a Windows utility, a web browser, or Telnet console.
An integration kit and a complete development kit are both available for evaluation and development use. The
development kit contains a development board, documents, sample code, cables, and accessories.
Product Features
The MiiNePort W1 series has the following features:
• 802.11 b/g compatible
• AES, WEP 64/128-bit, WPA, WPA2, PSK, 802.11i security support
• 1 Serial port, up to 921.6k bps
• 1 Ethernet port, 10/100Mbps
• SSL/SSH support for configuration
• Fast roaming to enhance connection reliabili ty
Product Specifications
Drop-in module
44.4 x 44.4 mm (1.75 x 1.75 in)
Information
1
10/100 Mbps, auto MDI/M DIX
IEEE 802.11b/g
Infrastructure mode (b/g), Ad-Hoc mode (b/g)
DSSS, CCK, OFDM
-71 dBm (Min)
Security:
-bit, WPA, WPA2, PSK, 802.11i
7, 8
1
TTL
MiiNePort W1 Series Introduction
31-
Stop Bits:
Parity:
Flow Control:
Baudrate:
Serial Signals
TTL:
Software
Network Protocols:
HTTPS
Configuration Options:
through the data port)
Windows Real COM Drivers:
Embedded CE 5.0/6.0, XP Embedded
Fixed TTY Drivers:
Solaris 10, FreeBSD, AIX 5.x
Linux Real TTY Drivers:
Operation Modes:
Environmental Limits
Operating
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models:
Storage Temperature:
Ambient Relative Humidity: 5 to 95% (non-condensing)
Power Requirements
Input Voltage:
Power Consumption:
Standards and Certifications
Safety:
EMC:
EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS:
EN 55024,
EN 61000
EN
EN 61000
EN 61000
EN 61000
EN 61000
EN 61000
Before connecting the hardware, follow the se impor tant w iring safety
Disconnect power source
Do not install or wire this unit or any attached devices with the power connected. Disconnect the power before
installation by removing the power cord before installing and/or wiring your unit.
Follow maximum current ra
Calculate the maximum possible curre nt in each power wire and com mon wire . Observe all elec trical codes
dictating the maximum current allowab le for ea c h wire siz e .
If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your
equipment.
Use caution
The unit will generate heat during operation, and the casing may feel hot to the touch. Take care when handling
unit. Be sure to leave adequate space for ventilation.
Wiring Requirements
tings
- unit may get h ot
The following guidelines will help ens ure trouble-free signal communication:
• Use separate paths to route wiring for power and devices to avoid inte rf er e nc e . Do not run signal or
communication wiring and power wiring in the same wire conduit. The r ul e of thumb is that wir ing that
shares similar electrical characteristics can be bundled together.
• If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the
intersection point.
• Keep input wiring and output wiring separate.
Label all wiring to each device in the system for easier testing and troubleshooting
precautions:
Black Diagram
MiiNePort W1 Series Getting Started
2-5
Hardware Installation
Steps for Installation
1. Attach the WLAN antenna to connect MiiNePor t W1
2. Let MiiNePort W1 Module connect todevice.
Software Installation
After physically installing the MiiNe Po rt W1, the module must be recognized on the new sys te m boar d by the
following steps.
Step for Installation
1. Apply power to the system board.
3
3. Compliance Notice
The following topics are covered in this chapter:
Federal Communications Commission Statement
Labeling Requirements
End Product Labeling
Information for OEM and Integrators
Antenna List
MiiNePort W1 Series Compliance Notice
3-2
WARNING
This is a Class B product. In a domestic environment, this product may cause radio interference. The user may
be required to take appropriate measures .
CAUTION
Any changes or modifications not express ly approv e d by the grante e of this device could
authority to operate the equipment.
WARNING
RF e
This equipment must be installed and operate d in acco rd ance w ith provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least
cm from all persons
and must not be co
users and
installers must be provide with antenna installation instructions and transmi tte r opera ting c onditions for
satisfying RF exposure compliance.
Federal Communications Commission
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reaso nab l e protec tio n agains t harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause har mful inte rference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Redirect or relocate the receiving antenna.
-Increase the distance between the equipment and receiver.
-Connect the equipment into an outlet on a circuit diff ere nt fro m that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technic ian for help.
void the user's
Labeling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this devic e
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
xposure warning
-located or operating in conjunction with any other antenna or transmitter. End-
.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
Contains FCC ID: SLE-W1
20
MiiNePort W1 Series Compliance Notice
3-3
Information for OEM and Integrators
The following statement must be included with all ver s ions of this document supplied to an
OEM or integrator, but should not be distributed to the end user .
1. This device is intended for OEM integrators only .
2. Please see the full Grant of Equipment document for other restrictions.
This radio transmitter FCCID: SLE-W1 has been approved by FCC to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Antenna List
No. Manufacturer Model No. Antenna Type Peak Gain
1 WANSHIH ANT-WDB-O-2 BK Dipole Antenna 2 dBi for 2.4GHz
2 KINSUN ANT-WDB-ARM-02 Dipole Antenna 1.21 dBi for 2.4GHz
Note: The antenna connector is Reverse SMA type.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.