P/N: 1802021000211
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
Tel:
Fax:
Moxa China (Shanghai office):
Toll
Tel:
Fax:
Moxa Europe:
Tel:
Fax:
Moxa Asia-Pacific:
Tel:
Fax:
Moxa India:
Tel:
Fax:
2019 Moxa Inc. All rights reserved.
UC-2100-W Series
Quick Installation Guide
Version 2.0, October 2019
-free: 1-888-669-2872
1-714-528-6777
1-714-528-6778
+49-89-3 70 03 99-0
+49-89-3 70 03 99-99
+91-80-4172-9088
+91-80-4132-1045
-free: 800-820-5036
+86-21-5258-9955
+86-21-5258-5505
+886-2-8919-1230
+886-2-8919-1231
*1802021000211*
Overview
NOTE
The console cable and power jack can be found inside the
product box, beneath the molded-pulp cushion.
The UC-2100-W Series computing platform is designed for embedded
data acquisition and processing applications. The computer comes with
up to two software-selectable RS-232/422/485 full-signal serial ports
and single or dual Ethernet LAN ports. In addition, the Arm-based
computing platform is available in various models that can fulfill diverse
interface requirements, such as dual serial, LAN ports, and wireless
connections. These versatile communication capabilities let users
efficiently adapt the palm-sized computing platform to a variety of
complex communications solutions.
Model Names and Package Checklist
The UC-2100-W Series includes the following models:
• UC-2114-T-LX
• UC-2116-T-LX
Before installing a UC-2100-W computer, verify that the package
contains the following items:
• UC-2100-W Series computer
• Console cable
• Power jack
• Quick Installation Guide (printed)
• Warranty card
Notify your sales representative if any of the above items are missing
or damaged.
- 2 -
Appearance
UC-2114
UC-2116
- 3 -
LED Indicators
LED Name
Status
Function
Power
Green
Power is on, and the device is
functioning normally
Off
Power is off
Ethernet
Green
Steady On: 10 Mbps Ethernet link
progress
Yellow
Steady On: 100 Mbps Ethernet link
progress
Off
Speed lower than 10 Mbps or the
cable is not connected
Ethernet
Green
Steady On: 100 Mbps Ethernet link
progress
progress
Off
Speed lower than 10 Mbps or the
cable is not connected
Serial (Tx)
Green
Serial port is transmitting data
Off
Serial port is not transmitting data
Yellow
Serial port is receiving data
Off
Serial port is not receiving data
User
Green/Yellow
User Programmable
LEDs that
Yellow
The number of glowing LEDs
1 LED : Poor
Off
Wireless module is not detected
CAN1/CAN2 (Tx)
Green
CAN port is transmitting data
Off
CAN port is not transmitting data
CAN1/CAN2 (Rx)
Green
CAN port is receiving data
Off
CAN port is not receiving data
The function of each LED is described in the table below:
(10/100 Mbps)
(10/100/1000
Mbps)
Serial (Rx)
indicate the
Wireless
signal strength
Blinking: Data transmission is in
Blinking: Data transmission is in
Blinking: Data transmission is in
Yellow Steady On: 1000 Mbps Ethernet link
Blinking: Data transmission is in
indicates the signal strength
3 LEDs: Excellent
2 LEDs : Good
Reset Button
The UC-2100-W Series computer is provided with a reset button, which
is located on the top panel of the computer. To reboot the computer,
press the reset button less than 1 second. Press and hold the reset
button between 7 to 9 seconds to reset the computer to the factory
default settings. When the reset button is held down, the User LED will
blink twice every second. The User LED will become steady when you
hold the button continuously for 7 to 9 seconds. Release the button
within this period to load the factory default settings.
- 4 -
Installing the Computer
NOTE
Do not run signal or communication wiring and power wiring in
the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
ATTENTION
This equipment is intended to be used in Restricted Access
Locations.
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Wiring Caution!
Calculate the maximum possible current in each power wire
and common wire. Observe all electrical codes dictating the
maximum current allo
goes above the maximum ratings, the wiring could overheat,
causing serious damage to your equipment.
Wall or Cabinet Mounting
Use two screws per side to mount the UC-2100-W Series on a wall or
inside a cabinet.
Wiring Requirements
Be sure to read and follow these common safety precautions before
proceeding with the installation of any electronic device:
• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
• Use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that
wiring that shares similar electrical characteristics can be bundled
together.
• Keep input wiring and output wiring separate.
• It is strongly advised that you label wiring to all devices for easy
identification.
UC-2100-W Series computers.
wable for each wire size. If the current
- 5 -
CAUTION
Be careful when handling the unit. When the unit is plugged in,
the internal components generate
outer casing may feel hot to the touch.
Connect the 9 to 48 VDC power line to the
I
This product is intended to be supplied by a UL Listed power
adapter
The power source must be
and minimum Tma = 75°C.
Connecting the Power
terminal block, which is connected to the UC2100-W Series computer. If the power is
supplied properly, the “Power” LED will glow a
solid green light. The power input location and
pin definition are shown in the adjacent
diagram. The input terminal block (CN5) is
suitable for a wire size of 12 to 30 AWG (3.3 to
0.05 mm
(4.425 lb-in).
MPORTANT
heat, and consequently the
2
) and a torque value of 0.5 N-m
or DC power source whose output meets SELV/LPS.
rated 9 to 48 VDC, minimum 0.6 A,
Grounding the Unit
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the terminal block connector to the grounding surface prior to
connecting the power. Please note that this product is intended to be
mounted on a well-grounded mounting surface, such as a metal panel.
The minimum cross-sectional area of the earthing conductor shall be
equal to the input wiring cable.
Connecting to the Console Port
The UC-2100-W console port is a 4-pin pin-header RS-232 port located
on the right panel of the case. It is designed for serial console
terminals, which are useful for viewing the boot up message, or for
debugging system boot up issues. Remove the protective cover on the
port to connect the console cable.
- 6 -
Serial Console Port & Pinouts
Serial Console Cable
Pin
Signal
1
TxD 2 RxD 3 NC 4 GND
Pin
10/100 Mbps
10/100/1000 Mbps
1
Tx+
TRD(0)+
2
Tx-
TRD(0)-
3
Rx+
TRD(1)+
4 – TRD(2)+
5 – TRD(2)-
6
Rx-
TRD(1)-
7 – TRD(3)+
8 – TRD(3)-
The serial ports are located on the bottom panel
of the
to
ser
connectors and can be configured for RS
RS
location and assignments are shown in the
following table.
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
TxDA(-)
TxDA(-)
– 2 RxD
TxDB(+)
TxDB(+)
– 3 TxD
RxDB(+)
RxDB(+)
DataB(+)
4
DTR
RxDA(-)
RxDA(-)
DataA(-)
5
GND
GND
GND
GND 6 DSR – – – 7
RTS – – – 8
CTS – –
–
Connecting to the Network
The Ethernet ports are located on the top or bottom panel of the UC2100-W computers. The pin assignments for the Ethernet port are
shown in the following figure. If you are using your own cable, make
sure that the pin assignments on the Ethernet cable connector match
the pin assignments on the Ethernet port.
Connecting to a Serial Device
UC-2100-W computer. Use a serial cable
connect your serial device to the computer’s
ial port. These serial ports have male DB9
-422, or RS-485 communication. The pin
Pin RS-232 RS-422
-232,
- 7 -
Connecting to a CAN Device
Pin
Signal
1
GND 2 L 3 Chassis 4 H 5 Vout
1. Remove the screw on the cover located
the SIM card and release it.
below the
.
To remove the
card, simply push the
card in and release it.
The UC-2114 and UC-2116 come with two CAN ports, which use the 5pin terminal block and are compatible with the CAN 2.0A/B standard.
The pin assignment of the port is shown below.
Installing SIM Cards
You will need to install a SIM card on your UC-2100-W computer.
Follow these steps to install the SIM card.
on the right panel.
2. Insert the SIM card into the socket.
Make sure you place the chip-side on
the bottom.
3. To remove the SIM card, simply push
Installing the microSD Card
Both UC-2114 and UC-2116 come with a storage socket that allows
users to install one microSD card. Follow these steps to install the
microSD card:
1. The microSD socket is located
right panel of the computer. Unfasten
the screw and remove the right panel
cover.
2. Insert the microSD card into the socket
Ensure that the card is inserted in the
right direction.
3. Replace the cover and fasten the screw
on the cover to secure the cover.
microSD
Adjusting the DIP Switch
The UC-2114 and UC-2116 computers come with one DIP switch for
users to adjust the serial port parameters. To set up the DIP s witch, do
the following:
- 8 -
1. Remove the screws on the DIP switch cover
located on the rear panel of the computer.
2. Remove the thin film on the DIP switch and
1 2 3 4 Low
High
Term.
–
ON
1 KΩ
1 KΩ
120 Ω
–
OFF
150 KΩ
150 KΩ
–
–
ATTENTION
There is a risk of explosion if the battery is replaced wi
incorrect type of battery
ATTENTION
Remember to choose the “VT100” terminal type. Use the
console cable to connect a PC to the UC
console port
Default IP Address
Netmask
LAN 1
192.168.3.127
255.255.255.0
LAN 2
192.168.4.127
255.255.255.0
adjust the setting as required.
Refer to the table below for the DIP switch
settings. The default value is OFF.
SW
Real-time Clock
The real-time clock in the UC-2100-W is powered by a lithium battery.
We strongly recommend that you do not replace the lithium battery
without the help of a Moxa support engineer. If you need to change the
battery, contact the Moxa RMA service team.
.
th an
Accessing the UC-2100-W Using a PC
You can use a PC to access the UC-2100-W by one of the following
methods:
A. Through the serial console port with the following settings:
Baudrate = 115200 bps, Parity = None, Data bits = 8, Stop bits
= 1, Flow Control = None.
.
B. Using SSH over the network.
Refer to the following IP addresses and login information:
Login: moxa
Password: moxa
- 9 -
-2100-W's serial
Loading...