Moxa 5650-8-T, 5650-8-S-SC, 5650-16-HV-T, 5650-8-HV-T, 5650-8 User Manual

...
P/N: 1802056000213
Technical Support Contact Information
www.moxa.com/support
Moxa Americas: Toll Tel: Fax:
Moxa China (Shanghai office): Toll Tel: Fax:
Moxa Europe: Tel: Fax:
Moxa Asia-Pacific: Tel: Fax:
Moxa India: Tel: Fax:
2015 Moxa Inc. All rights reserved.
NPort 5600 Series
Quick Installation Guide
Edition 5.0, November 2015
-free: 1-888-669-2872 1-714-528-6777
1-714-528-6778
+49-89-3 70 03 99-0
+49-89-3 70 03 99-99
+91-80-4172-9088
+91-80-4132-1045
-free: 800-820-5036 +86-21-5258-9955
+86-21-5258-5505
+886-2-8919-1230
+886-2-8919-1231
*1802056000213*

Overview

NOTE
The wide temperature model does not come with LCM display panels or push buttons. All of the LCM descriptions below apply only to standard temperature models.
Welcome to the Moxa NPort 5600 Series. The NPort 5610-8/16 have 8 or 16 RS-232 ports, the NPort 5630-8/16 have 8 or 16 RS-422/485 ports, and the NPort 5650-8/16 have 8 or 16 RS-232/422/485 ports.

NPort 5600 Series Models

The NPort 5600 Series includes the following models: NPort 5610-8, NPort 5610-16, NPort 5610-8-48V, NPort 5610-16-48V, NPort 5630-8, NPort 5630-16, NPort 5650-8, NPort 5650-8-T, NPort 5650-8-HV-T, NPort 5650-16-HV-T, NPort 5650-16, NPort 5650-16-T, NPort 5650-8-M-SC, NPort 5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.

Package Checklist

The NPort 5600 package should contain the following items:
• 1 NPort 5600 series serial device server
• Power cord (AC models only)
• NPort Documentation & Software CD
• NPort 5600 Quick Installation Guide
Optional Accessories:
• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm
• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm
• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm
• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cm
Note: Please notify your sales representative if any of the above items is missing or damaged.

Hardware Introduction

The front and rear panels are shown below:
Front panel of the NPort 5600 Series
Rear panel of the NPort 5610/5630/5650 (AC Power)
Rear panel of the NPort 5650 (Fiber Model)
Rear panel of the NPort 5610 (DC Power)
- 2 -
Front panel of the NPort 5650-T Series
Name
Color
Function
Off
Power is off, or power error condition exists.
Steady on: Power is on and the NPort is booting up.
Blinking: Indicates an I P conflict, or DHCP or BOOTP server did not respond properly.
functioning
normally.
Blinking: The NPort has been loca ted by NPort Administrator’s Location function.
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
No data is being transmitted or received through the serial port.
N P 5 6 1 0 - 1 6 3 8
1 9 2 . 1 6 8 . 1 2 7 . 2 5 4
Button
Action
MENU
Activates the main menu, or returns to a lower level.
Scrolls up through a list of items shown on th e LCM panel’s second line.
panel’s second line.
SEL
Selects the option listed on the LCM panel’s second line.
Reset Button—press the Reset button continuously for 5 sec to load factory defaults: Use a pointed object to press the reset button. Release
the button after the Ready LED stops blinking. LED Indicators on the Front Panel—the front panels of the NPort 5600
have several LED indicators, as described in the following tabl e.
Red
Ready
Steady on: Power is on and the NPort is
Green
1 to 16
Off
LCM Display Panel—If the NPort is working properly, the LCM panel will display a green color. The red Ready LED will also light up, indicating that the NPort is receiving power. After the red Ready LED turns green, you will see a display similar to:
This is where:
NP5610-16 is the NPort’s name
38 is the NPort’s local sequence number
192.168.127.254 is the NPort’s IP address LCM Panel Operation—There are four buttons on the NPort 5600’s front
panel. These buttons are used to operate the server’s LCM panel. Going from left to right, the buttons are:
︿
Scrolls down through a list of items shown on the LCM
Detailed LCM Panel Operating instructions can be found in the NPort 5600 Series User’s Manual on the CD-ROM.
- 3 -
Link Indicator on the rear panel of the NPort 5650 fiber
LED Name
LED Color
LED Function
Off
Fiber disconnected.
Green
Fiber connected, data not transmitting.
Blinking
Fiber connected, data is transmitting.
Take NPort 5610-8-48V as an example. Loosen the screws on the V+ and V 5610 cord’s 48 VDC or -48 VDC wire to the terminal block’s
V+ terminal, and the power cord’s DC Power Grou nd wire to th e terminal block’s V The NPort Power Ground are reversed.)
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. The Shielded Ground (sometimes called Protected Grou nd) contact is the second contact from the right of the
5-pin power terminal block connector located on the rear panel of the NPort 5610-8-48V. Connect the SG wire to the Earth ground.
model—the rear panels of the NPort 5650 have a link indicator, as described in the following table.
Link

Hardware Installation

STEP 1: After removing the NPort 5600 from the box, the first thing you
should do is attach the power adapter.
STEP 2: Connecting the Power. AC: Connect the NPort 5600’s 100-240 VAC power cord to the A C
connector. The “Ready” LED will show a solid red color until the syst em is ready, at which time it will change to a green color.
DC: Connect the NPort 5600 VDC’s power cord to the DC connector, and then follow the steps given below:
-8-48V’s terminal block. Connect the power
- terminal, and then tighten the terminal block screws. (Note: 5610-8-48V can still operate even if the 48V/-48V and DC
The “Ready” LED will show a solid red color until the system is ready, at which time it will change to a green color.
Grounding the NPort 5600 VDC:
STEP 3: Connect the NPort 5600 to a network. Use a standard
straight-through Ethernet cable to connect to a hub or switch. When setting up or testing the NPort 5600, you might find it convenient to connect directly to your computer’s Ethernet port. In thi s case, use a cross-over Ethernet cable.
STEP 4: Connect the NPort 5600’s serial port to a serial device. Placement Options: You can place the NPort 5600 on a desktop or other
horizontal surface.
- terminals of the NPort
- 4 -

Software Installation Information

Serial Port Pinouts for the NPort 5610
Serial Port Pinouts for theNPort 5630
Pin
RS-232
1
DSR (in)
2
RTS(out)
3
GND
4
TxD(out)
5
RxD(in)
6
DCD(in)
7
CTS(in)
8
DTR(out)
RS-422/
RS-485-4W
1 – –
2 – – 3 TxD+
– 4 TxD-
– 5 RxD-
Data- 6 RxD+
Data+ 7 GND
GND 8 –
Pin
RS-232
RS-422/RS-485-4W
RS-485-2W
1
DTR – – 2 RTS
TxD+
3
GND
GND
GND
4
TxD
TxD-
– 5 RxD
RxD+
Data+
6
DCD
RxD-
Data-
7
CTS – – 8 DTR – –
To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort Installation CD window opens, click on the INSTALL UTILITY button,
and then follow the instructions on the screen. To view detailed information about NPort Administration Suite, click
on the DOCUMENTS button, and then select “NPort 5600 Series User’s Manual” to open the PDF version of this user’s guide.

Pin Assignments and Cable Wiring

Pin
Serial Port Pinouts for the NPort 5650
Serial Cables for the NPort 5630 (2-wire RS-485)
RS-485-2W
- 5 -
Serial Cables for the NPort 5630 (RS-422/4-wire RS-485)
Serial Cables for the NPort 5610/5650 (RS-232)
Serial Cables for the NPort 5650 (RS-422/4-wire RS-485)
Serial Cables for the NPort 5650(2-wire RS-485)
- 6 -
Loading...