Moxa 5600-8-DTL User Manual

P/N: 1802056000011

Name

Color

Function

red

Power is on.

off

Power is off.

resetting to factory default

off

Power is off or fault condition exists.

Fault
red

IP conflict or DHCP or BOOTP server did not
respond properly.

off

No fault condition detected.

Name

Color

Function

Link

green

Steady: Network is connected; no data is

being transmitted.

short.

InUse

green

Serial port has been opened by server side
software.

Serial port is not currently opened by server
side software.

TX/RX

green (Tx)

Serial device is transmitting data.

orange (Rx)

Serial device is receiving data.

off

No data is flowing to or from the serial port.

Hardware Introduction

Top and Rear Views

NPort 5600-8-DTL

being transmitted.
Blinking: Network is connected; data is

Quick Installation Guide

Second Edition, October 2014

Overview

The NPort 5600-8-DTL series includes the following models:

• NPort 5610-8-DTL: 8 ports, RS-232, 0 to 60°C

• NPort 5650-8-DTL: 8 ports, RS-232/422/485, 0 to 60°C

• NPort 5650I-8-DTL: 8 ports, RS-232/422/485, 0 to 60°C,

2KV optical isolation.

• NPort 5610-8-DTL-T: 8 ports, RS-232, -40 to 75°C

• NPort 5650-8-DTL-T: 8 ports, RS-232/422/485, -40 to 75°C

• NPort 5650I-8-DTL-T: 8 ports, RS-232/422/485, 2KV

optical isolation, -40 to 75°C

Package Checklist

The NPort 5600-8-DTL package should contain the following items:

• NPort 5600-8-DTL device server

• Wall mounting and DIN-Rail kits

• Stick-on pads

• Power adapter (not including T models)

• Documentation and software CD

• Quick installation guide (printed)

• Warranty card

Optional Accessories*

• DK-35A: DIN-Rail mounting kit (35 mm)

Note: Please notify your sales representative if any of the above
items are missing or damaged.

*Optional Accessories can be ordered separately.

Front View

Reset Button

Use a pointed object to hold the reset button down for at least five
seconds to load the factory defaults. Release the reset button
when the Ready LED stops blinking.

LED Indicators

The LED indicators on the top panel are used to display the status
as follows:

PWR

off Ethernet cable is disconnected or has a

(P1 to
P8)

(P1 to
P8)

off

Hardware Installation

STEP 1: After removing the NPort 5600-8-DTL from the box, place

it on a desktop or other horizontal surface. Connect the 12-48 VDC
power adaptor to the NPort 5600-8-DTL’s power input when using
an AC power source, or connect the NPort 5600-8-DTL’s terminal
block directly to a DC power source.

STEP 2: Use an Ethernet cable to connect the NPort 5600-8-DTL to
a network hub or switch. You can also connect directly to your
computer’s Ethernet port, which is convenient for initial
configuration or testing.

STEP 3: Connect the NPort 5600-8-DTL’s serial port to a serial
device.

Wall or Cabinet Mounting

The NPort 5600-8-DTL comes with two metal attachment plates to
allow installation on a wall or the inside of a cabinet. First, attach
the brackets to the back of the NPort with screws. Next, mount the
unit on a wall or cabinet with screws. Screws should be less than

6.0 mm in head diameter, and less than 3.5 mm in shaft diameter.

Ready green Steady: NPort is operational

– 1 – – 2 – – 3 –

Blinking: NPort is responding to NPort
Administrator “Locate” function or NPort is

The Americas:

[phone] (toll-free: 1-888-669-2872)

Europe:

[phone]

Asia-Pacific:

[phone]

China:

[phone] (toll-free: 800-820-5036)

 2014 Moxa Inc., All Rights Reserved

Standard Attachment

DK-35A Attachment

Pin

RS-232

RS-422/
RS-485-4W

RS-485-2W

1

DCD

TxD-(A)

– 2 RxD

TxD+(B)

– 3 TxD

RxD+(B)

Data+(B)

4

DTR

RxD-(A)

Data-(A)

5

GND

GND

GND 6 DSR – – 7 RTS – – 8 CTS – – 9 – – –

232

DIN-Rail Mounting

DIN-Rail attachments can be purchased separately to attach the
product to a DIN-Rail. The DIN-Rail attachments should be
oriented with the metal springs on top.

Software Installation Information

To install NPort Administration Suite, insert the NPort
Document & Software CD into your PC’s CD-ROM drive. Locate

and run the setup program and follow the on-screen instructions.
The setup program will be named
Npadm_Setup_[Version]_Build_[DateTime].exe (e.g., “Npadm
_Setup_Ver1.16_Build_11021010.exe”). Refer to the NPort
5600-8-DTL User’s Manual for more details.

Pin Assignments

DB9 Male Ports

Note: The NPort 5610-8-DTL supports RS­only.

Specifications

LAN

Ethernet Ports: 10/100 Mbps (RJ45)
Protection: Built-in 1.5 KV magnetic isolation

Serial Interface

RS-232: NPort 5610-8-DTL
RS-232/422/485: NPort 5650-8-DTL, 5650I-8-DTL
Serial Ports: 8 (DB9-M connectors)
Isolation: 2 KV isolation (NPort 5650I-8-DTL)

Serial Signals

RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485 (2-wire): Data+, Data-, GND
RS-485 (4-wire): Tx+, Tx-, Rx+, Rx-, GND
Serial Line Protection: 15 KV ESD for all signals
RS-485 Data Direction: ADDC™ (Automatic Data Direction

Control)

Serial Communication Parameters

Parity: None, Even, Odd, Space, Mark
Data Bits: 5, 6, 7, 8
Stop Bit(s): 1, 1.5, 2
Flow Control: RTS/CTS, DSR/DTR (for RS-232 only), XON/XOFF
Transmission Speed: 50 bps to 921.6 Kbps

Power Requirements

Power Input: 12 to 48 VDC

Physical Characteristics

Operating Temperature:

Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)

Storage Temperature: -40 to 85°C (-40 to 185°F)
Operating Humidity: 5 to 95% RH
Material: SECC sheet metal (0.8 mm)
Dimensions:

Without ears: 197 × 44 × 125 mm
With ears: 229 × 46 × 125 mm
With DIN-Rail kit: 197 × 52.8 × 125 mm

Certifications

Regulatory Approvals: FCC Class A, CE Class A, UL 60950-1,

LVD

Warranty: 5 years

www.moxa.com/support

– 4 – – 5 – – 6 –