Mountz EMT 6, EMT 9, EMT 50, EMT 80 Operating Instructions Manual

Ergo Micro Torque (Externally Adjustable) Screwdriver Operating Instructions

Rev 3.0 (September 22, 2010)

Corporate Headquarters: 1080 North 11th Street, San Jose, CA95112 Phone: [phone] Fax: [phone]

www.mountztorque.com

Calibrating Torque Screwdrivers

To calibrate torque screwdrivers either use a torque analyzer or torque transducer within the
range of the torque screwdriver. For torque screwdrivers calibrate torque in "Peak" mode with an
analyzer or transducer. Make sure to apply the torque slowly and smoothly.

1. Select a torque analyzer or transducer that covers the torque range of the EMT screwdriver.
Connect screwdriver to the torque analyzer or transducer using the appropriate adapters as
needed.

2. Apply torque clockwise slowly until screwdriver 'slips' and note reading.

3. Adjust screwdriver to required torque setting as described below.

4. Test and repeat adjustment as necessary to obtain desired value.

5. Recalibrate torque screwdriver at prescribed intervals.

Adjusting Torque Setting (During Calibration)

1. Insert hex key into hole located at end of rubber grip.
(Note do-not attempt to remove rubber grip from the tool).

2. Turn hex key clockwise to increase torque and counter
clockwise to decrease torque. Do not adjust torque above or
below the recommended torque ranges.

3. Seal End Hole with Black RTV Sealant.

EMT 6, 9, 50 & 80 models are supplied with a T-Bar

1. Snap T-Bar into the slot located in the grip.

Setting and Applying Torque

1. Set desired torque on the scale. Pull down on the "Adjustment Ring"
and turn handle clockwise to increase torque and counter clockwise to decrease torque on the scale. Align the desired
torque value on the micrometer scale. Release "Adjustment Ring."

2. Tighten nut or bolt by applying steady twists. Screwdriver should be kept at 90 degrees to axis of bolt during tightening.
When pre-set torque is reached, the screwdriver will 'slip.'

3. The screwdriver will automatically reset itself for the next application.

4. With its unique cam-over design, it's impossible to over tighten beyond the preset
load.

Torque Scale

Adjustment Ring

Bit holder

Bottom Scale

Insert hex key

Contact

Mountz Inc.

Phone: [phone]

Fax: [phone]

[email protected]

www.mountztorque.com

Looking for fasteners?

www.mrmetric.com

Ergo Micro Torque (Externally Adjustable) Screwdriver Operating Instructions

Rev 3.0 (September 22, 2010)

Corporate Headquarters: 1080 North 11th Street, San Jose, CA95112 Phone: [phone] Fax: [phone]

www.mountztorque.com

Tool Lubrication

It is recommend the tool is re-lubricated after 3 years or 15000 cycle which ever comes first.
Lubrication is as follows
Total Nevastance SFG-2 grease is used on the ball housings
Multis EP2 is used on the handle threads
3 in 1 oil is used on the bearing assembly between the main ball and the spring

Testing & Servicing

In order to maintain accuracy, it is crucial that torque control measuring
equipment be calibrated regularly.

We recommend a general once a year calibration interval. However, it is
the user’s organization that must determine suitable intervals based upon
equipment performance, application, degree of usage and management
objectives.

For calibration, re-adjustment or repairs, please send the tool to one of
our 3 service locations.

Torque Scale

Adjustment Ring

Bit holder

Bottom Scale

Mountz Service Locations

Eastern Service Center

19051 Underwood Rd.
Foley, AL 36535
Phone: [phone]
Fax: [phone]

Western Service Center

1080 N.11th Street
San Jose, CA 95112
Phone: [phone]
Fax: [phone]

Mexico Service Center

Mountz Mexico SA de CV Chihuahua
Av. Cristobal Colon #15343
Col. Paseos de Chihuahua
Chihuahua, Chih. Mexico CP 31125
Phone: [phone]
Fax: [phone]

www.etorque.com

Download a “Service Form” and include a copy

when you send the tools in to be serviced.