Page 1
Dual Monitor Desk Mount
Instruction Manual
MU6002
If you have any questions , please contact us.
75x75
100x100
32"
(2~8kg)x2
(4.4~17.6lbs)x2
V2.0
Page 2
WARNING!
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x2)
Upper Arm
G(x5)
M6x10
L (x2)
Bolt
M-A (x8)
M4x12
B (x2)
Lower Arm
H(x4)
Pad
M (x1)
Support Plate
M-B (x8)
M6x12
(17.6lbs)x2
(8kg)x2
DO NOT EXCEED WEIGHT CAPACITY.
C (x1)
Base
I (x1)
Grommet Base
N (x1)
3mm Allen Key
M-C (x8)
D6 Washer
01
D (x2)
VESA Plate
J (x1)
Wingnut
O (x1)
4mm Allen Key
E (x1)
Bracket
F (x1)
Clamp
K (x1)
Carriage Bolt
P (x1)
6mm Allen Key
M-D (x8)
spacer
NOTE: Not all hardware included will be used.
Page 3
ASSEMBLY STEPS
E
E
STEP 1: Apply Pads to the Base Bottom
Apply pads (H) to the base
bottom to avoid desk scratches.
H
C
STEP 2: Clamp Installation or Grommet Base Installation
OPTION A: Clamp Installation
Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O).
Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O).
Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P).
C
E
G
O
E
G
10-60mm
OR
F
G
O
10-90mm
O
F
OR
P
02
Page 4
STEP 2: (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I).
Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O).
Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J).
Last step, tighten Wingnut (J).
C
G
I
K
M
J
O
10-90mm
03
Page 5
STEP 3: Arm Installation
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw
using Allen key (N).
B
C
F
Note: Please note that the side with
the label“ ” is installed on the
base(C) when installing the lower
arm(B) to the base (C).
DO NOT tighten the
screw excessively or
it might be stripped.
N
A
DO NOT tighten the
screw excessively or
it might be stripped.
N
04
Page 6
STEP 4: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and
secure with screws(M-A)or(M-B) with washers(M-C)
using 6 mm Allen Key (P). Do not tighten the screws
excessively or your monitor might be damaged.
D
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure
with screws (M-A) or (M-B) with washers (M-C)and
spacers(M-D)using 6 mm Allen Key (P). Do not tighten
the screws excessively or your monitor might be damaged.
M-A
M-B
M-C
CAUTION:To select the correct screws(M-A or M-B)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
P
M-A
M-D
D
M-B
M-C
P
05
Page 7
STEP 5: Hang Monitor
Slide the monitor onto the head of swivel arm, install the security bolt (L). Make sure the security
bolt is installed before you rotate the monitor.
L
Important Notice:
The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the
monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the
monitor in a slow & gentle way while observing whether the arms will fall down wildly.
spring arm falls down greatly.
Guideline to adjust monitor tilting angle.
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten th e tilting bolt to
P
06
Page 8
STEP 6: Adjust Tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in upper arm (A) using 6 mm allen key (P).
P
CAUTION
Note1:
Be sure to keep the arm in horizontal position during adjustment.
If the monitor falls down and fails to stay at the desired
height by itself:
Turn counter -clockwise(“+”d irection) to increase gas
Falls down
spring tension until the monitor can st ay at the desir ed
hei ght by itself.
Rises up
If the monitor rises up and fails to stay at the desired
height by itself:
Turn clockwise(“-”dir ection) to reduce gas sprin g tensio n
until t he monitor can s tay at the desi red height by it self.
Note2:
As for how many circles the screw should be turned, refer to below diagram.
Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST)
min
1 4 8 11 14 17
07
Page 9
STEP 5: (Continued)
STEP 7: Cable Management
Remove bottom plastic covers from gas spring arm as shown in diagram.
Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.
08
Page 10
Adjust as Desired
Adjust monitor position and rotation.
18 0°
+90 °
27 0°
36 0°
36 0°
-45 °
DESK
Pay attention while clamp install !
09
DESK
Page 11
Product Dimensions
3.9"
100mm
55mm
2.2“
270°
360°
6.3“
160mm 200mm-280mm 63mm
0.39-3.5"
10-90mm
7.87"-11"
180°
2.5“
2.95"
75mm
3.94"
100mm
4.5"
114mm
2.95"
75mm
360°
3.94"
100mm
4.5"
114mm
+90°
-45°
9.4"
240mm
6.9"-16.9"
175-430mm
10
Page 12
CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
Loading...