Mountain Off Road 8795-2 User Manual

MOUNTAIN OFF ROAD ENTERPRISES. LLC.

P.O. BOX 690

DELTA, COLORADO 81416

970-625-0500

E-mail: [e-mail]

www.mountainoffroad.com

INSTALLATION INSTRUCTIONS FOR 8795-2

PLEASE READ AND UNDERSTAND TERMS/POLICIES BEFORE YOU INSTALL THIS SYSTEM

M.O.R.E. Shackle Reversal System (S.R.S.™) # 8795-2 contains the following items:

ITEM DESCRIPTION QUANTITY PART NUMBER

A Pivot Bracket-Drivers Side 1 8795-DS
B Pivot Bracket-Pass Side 1 8795-PS
C Bushing-Aluminum 4 8795-125
D Bracket-Shackle Hanger 2 SR104
E Bolt-Shackle Hanger 3/8”x1” 2 18834
F Washers-Lock & Flat 3/8” 2 33008/33622
G Tube Spacer 3/4”x2-3/4” 1 S101299
H Tube Spacer 3/4”x2-3/8” 4 S101399
I Bolt-Spring Pivot 9/16”X4-1/2” 2 13271
J Bolt-Pivot Bracket to Frame 1/2”x4-1/2” 3 13221
K Bolt-Pivot Bracket to Frame 1/2”x1-1/4” 2 13207
L Bolt-Shackle Hanger to Frame 1/2”x4” 4 13219
M Nut-Crimp Lock 9/16” 2 37270
N Nut-Crimp Lock 1/2” 9 37268
O Washer-Flat 1/2” 20 33086
P Washer-Flat 9/16” 4 33088

- Instruction Sheet 1 8795-2 IS

Photo of items on page 2 of these instructions. Please familiarize yourself with all components in the system.
These instructions will refer to items by letter, not description. Read all instructions carefully before work is
started on your vehicle. In addition to basic hand tools, the following specialty tools are needed to perform this
installation: Angle head drill (electric or air), 3/4” diameter drill bit, 1/2” diameter drill bit, 21/64” drill bit, 3/8-24
(fine thread) tap, floor jack, jack stands (4), torque wrench, grinder and or cutting torch.

FIT and TOLERANCES: All parts in this system are the results of countless hours of research, testing, fitting
and refining. Jeep® frames have a wide tolerance on bolt hole centers from frame to frame. This is why

M.O.R.E.™ has installed several “slots” in which to mount our bracketry. In addition to the factory tolerances,
most people install other then factory equipment such as bumpers, winch mounts, springs etc. M.O.R.E.™ has

done the best job we can to insure that our parts fit with the different possibilities. However, you may find it nec­essary to grind, elongate, bend, or force the parts in this system to fit on your rig. Please use common sense
when installing these parts, and understand that if you modify them in any way, they are not returnable!!

8795-2 PAGE 1

8795-2 S.R.S.™ Contents

N

J

G

B

K

E

D

C

F

P

M

A

I

H

O

L

Notes:

8795-2 PAGE 2

8795-2 S.R.S.™ - GENERAL INFORMATION:

This system will fit Jeep® YJ Wrangler vehicles with any engine. This system will lift the front of the Jeep® one

inch (1”) over where it sits now. Before starting this installation, check the frame to make sure it is in good condi-

tion, is straight and has no excessive rust. Only install it on vehicles in good sound condition. This system will
work with stock or most aftermarket bumpers, with or without a winch. No welding is required for installation.
There will be some drilling and grinding, however.

LEAF SPRINGS: This system has been designed to work with stock and aftermarket leaf springs. It has been

tested with several different manufactures springs up to 3.5” lift and works fine. It will work with stock springs that
have been placed on top of the YJ’s axle housings (spring over axle).

PITMAN ARM: You may need to use a stock pitman arm. If a “dropped” arm is used there is a possibility that the
tie rod could contact the drag link upon suspension compression.

DRIVE SHAFT: The front drive shaft will need to be modified. A longer travel slip-yoke needs to be installed.
Due to the suspension movement the stock slip-yoke will not have enough travel and the fact that this system will

push the axle forward aprox. one inch, the stock shaft length will not be enough. M.O.R.E.™ recommends call­ing Tom Wood’s Custom Drive Shafts at: 877-497-4238.

BRAKE HOSES: The stock brake hoses will work if you are using stock leaf springs, under the axle. If you have
any lift in your springs, or a spring over axle conversion, the stock hoses will have to be replaced with longer
ones. M.O.R.E.™ Has Extended Stainless Braided Brake Lines available if needed.

TERMS/POLICIES

DAMAGE CLAIMS: All orders are carefully packed, however, mishandling by the carrier can result in damage. The carrier has the responsibility for the shipment

from the time it leaves our warehouse until it is delivered to you. All claims for lost or damaged goods should be reported to the carrier, not to M.O.R.E.™ LLC.

RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. After you receive a Return Goods Authorization (RGA) number, merchan-
dise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA num­ber written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be de­fective or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsal­able condition.

WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void this
warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee the performance of any items.
M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which
they are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installa­tion of such products.

PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous condition which could
cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ LLC. are for
racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal injury or property damage arising from the failure of any
parts manufactured or sold by M.O.R.E.™ LLC.

Specifications are subject to change without notice.

Jeep®, AMC®, CJ®, YJ®, TJ® Wrangler®, are registered trademarks of DaimlerChrysler.

M.O.R.E.™ is not affiliated with DaimlerChrysler.

M.0.R.E™, BombProof™, S.R.S.™, SlipLoc™, DoubleJointed™, RockProof™, are trademarks used by Mountain Off Road Enterprises, LLC . These instruc-

tions, our catalog, web site, and logo are copyright©, 1996-2008.

8795-2 PAGE 3